Guardian 00260 User manual

Do not throw instructions away.
Read and understand instructions before
using this equipment.
ANGEL ANCHOR
Part #: 
Instruction Manual
 Rev. I
2 Introduction
2 Worker Classifications
2 Applicable Safety Standards
2 Product Specific Applications
3 Correct Anchor Positioning
4 Product Specifications and Materials
5 Installation and Use
6 Maintenance, Cleaning, and Storage
6 Limitations
6 Compatibility
7 Safety Information
8 Labels
9 Diagrams
9 Inspection
10 Inspection Log

2
Applicable Safety Standards
When used according to instruction
specifications, this product meets or exceeds all
applicable OSHA 1910.140 & 1926.502 standards
for fall protection. Applicable standards and
regulations depend on the type of work being
done, and also might include state-specific
regulations. Consult regulatory agencies for
more information on personal fall arrest systems
and associated components.
Worker Classifications
CAUTION! Understand the following
definitions of those who will work near or
who may be exposed to a fall.
Qualified Person: A person with an
accredited degree or certification, and with
extensive experience or suicient professional
standing, who is considered proficient in
planning and reviewing the conformity of fall
protection and rescue systems.
Competent Person: A highly trained and
experienced person who is ASSIGNED BY
THE EMPLOYER to be responsible for all
elements of a fall safety program, including,
but not limited to, its regulation, management,
and application. A person who is proficient
in identifying existing and predictable fall
hazards, and who has the authority to stop
work in order to eliminate hazards.
Authorised Person: A person who is
assigned by their employer to work around or
be subject to potential or existing fall hazards.
It is the responsibility of a Qualified or
Competent person to supervise the job site
and ensure all applicable safety regulations
are complied with.
WARNING! Use of equipment in
unintended applications may result
in serious injury or death. Maximum 1
attachment per connection point.
Product Specific Applications
May be used to support a MAXIMUM 1 in
a Personal Fall Arrest System (PFAS)
for use in Fall Arrest applications.
Structure must withstand loads applied in the
directions permitted by the system of at least
5,000 lb (22.2 kN) Maximum free fall is 6' (1.8 m),
or up to 12' (3.7 m) if used in combination with
equipment explicitly certified for such use.
D-ring: Dorsal
May be used in Travel Restraint
applications. Restraint systems prevent
a worker from reaching the leading edge
of a fall hazard. Always account for fully deployed
length of lanyard/SRL. No free fall is permitted.
Restraint systems may only be used on surfaces
with slopes up to 18.4  (4/12 - vertical/horizontal).
D-rings: Dorsal, Side
Introduction
Thank you for purchasing a Guardian Angel
Anchor. This manual must be read and
understood in its entirety, and used as part of an
employee training program as required by OSHA
or any applicable state agency.
This and any other included instructions must
be made available to the user of the equipment.
The user must understand how to safely and
eectively use the Angel Anchor, and all fall
safety equipment used in combination with the
Angel Anchor.

3
Correct Anchor Positioning
This chart details allowable working zones required to reduce risk of swing falls and improper side loading.
ALWAYS adhere to information specified by chart.
For example, if the anchorage connector is 6’ (1.8 m) from the leading edge (Y), the working distance (X) is
8’ (2.4 m) in each direction from the perpendicular, which translates to a 53° working angle.
Anchor Distance From
Leading Edge (Y)
Working Distance Along Roof
Edge (Either Direction) (X)
Working Direction from
Perpendicular (Ø)
6 ft 8 ft 53 °
10 ft 9 ft 9 in 45 °
15 ft 11 ft 7 in 38 °
20 ft 13 ft 3 in 33 °
25 ft 14 ft 6 in 30 °
30 ft 16 ft 28 °
35 ft 17 ft 2 in 26 °
40 ft 18 ft 3 in 24 °
45 ft 19 ft 4 in 23 °
50 ft 19 ft 10 in 21 °
55 ft 21 ft 4 in 21 °
60 ft 22 ft 3 in 21 °

4
Materials
Galvanized steel
Part # Description
00260 Angel Anchor
Weighted Pad (12)
Frame Member (6)
Central Frame
Connection Point
#00380 Swivel Top
Attachment (Not Included)
SRL (Not Included)
Locking Bar (12) inserted
through Pad Collar and
secured with Pin (12)
Specifications

5
Installation
Step 1: Select the intended position of the
Angel Anchor, ensuring that no part of the
anchor is less than 10’ (3 m) from any edge,
roof opening, or leading edge. Installation
location MUST be free for all loose materials,
debris, and hazardous materials.
Step 2: Place Central Frame at selected
installation location, and arrange (12)
Weighted Pads around frame.
Step 3: With the anti-skid/rubber padding
side down, slide one Weighted Pad onto each
frame member, 3/4 down the tube.
Step 4: Slide a second Weighted Pad onto
each frame member, anti-skid side down. Pad
collar must be completely on frame member.
Step 5: Align holes on frame with Weighted
Pad collar holes, then insert locking bars and
secure with pins.
Step 6: Inspect to ensure all Weighted Pads
are fully secured to frame.
Step 7: Connect complete and compatible
PFAS to provided anchor point.
Installation and Use
Prior to installation, plan your system:
Determine suitable location for anchor;
ensure location is free of debris, rot, decay,
cracking, and hazardous materials. Only use
Angel Anchor on the following approved
substrates:
EPDM membrane
Torch down (smooth)
Torch down (granulated)
Cement, Wood
TPO
Vinyl
PVC
Ensure Angel Anchor Weighted Pads have
wear-resistant natural gum foam rubber
padding aixed prior to use.
Eliminate/minimize all risks of swing fall.
Compatible for use on surfaces with pitches
up to 1/12 (5°).
ALWAYS place anchor on roof pitch opposite
work surface, and a MINIMUM 10' (3 m) from
both the ridge and all leading edges.
WARNING!Wind load rating: 85 MPH
(137 KPH). DO NOT USE if potential exists
for exposure to wind gusts greater than
85 MPH (137 KPH).
WARNING!Angel Anchor may be used in
combination with a compatible horizontal
lifeline (HLL) system for use in Restraint
applications ONLY. Maximum 2 workers
per Angel Anchor HLL system.
Angel Anchor
MAX 5°
10 ‘ (3 m) MIN
Work Surface