Hanil FLETA 4 User manual

Save Select the program number → Press the Program button → Set the run parameters
→ Press the Enter button
Cursor keys / Enter
Function selection(◀,▶)
Increase or decrease
the values(▲,▼)
Save the values ( )
Quick Guide Fleta 4
Display & Control 안내
Cat. No. : FL-4
RPM setting mode : RPM flashes
RCF setting mode : RCF flashes
Time setting mode : 00’ 00’’ flashes Call up Select the program number → Press Setup / Enter button
Setting Run
Parameters
(RPM / RCF /
Time / ACC /
DEC / Rotor ID)
Display Sceen
RPM / RCF / Time / Program / Rotor ID / ACC / DEC
Program Save / Call
Saving / Calling up a
program (Up to 10)
Lid Open
Press the
Enter button
Press the
Enter button
Select a parameter to be
changed (Press ◀ or ▶ button)
+ Up or down the values
(Press ▲ or ▼ button)
Press the
Setup / Enter
button
Press the
Program button
Select the program number
(Press ▲ or ▼ button)
Rotor ID mode : Rotor flashes
ACC / DEC setting mode : ACC / DEC flashes
Max. RPM 4,000 rpm
Max. RCF
3,243 xg
Timer
< 100 min, Pulse
continuous
ACC / DEC
Ramps
5/6
Start / Stop / Pulse
Pulse
After reaching the set speed,
the centrifugation is decelated
and stopped
Serial No. Installation Date
Saving / Calling
Up a Program

Quick Guide Fleta 4
Cat. No. : FL-4
Check the rotor is firmly tightend onto
the motor shaft.
Check the Rotor Locking
After relocating the device or loading the
rotor, balance them by using a leveler.
If necessary, level the device by adjusting the
‘Leveling foot’ on the bottom of the device.
Balancing the Centrifuge and Rotor
Check the cushion rubbers in
the sleeves (AL15-12, AL15-24)
before use. When reinserting,
must insert it in the correct
direction.
Spread the grease lightly on
the bucket where it contacts
the rotor and the pivot.
Clean the chamber and
rotor by wiping with a cloth
soaked in mild detergent
and dry completely.
Check the Cushion Rubbers Care of Swing-Out Rotor
Cleaning
Check the rotor, buckets and tubes are free
of scratch and crack before operation.
Check the Accessories for Abnormalities
Load tubes symmetrically into the rotor
with identical amount.
Load Tubes Symmetrically
Allow a safety clearance of 30 cm around the
centrifuge during operation.
If the centrifuge lid cannot be opened, insert the provided
T-wrench into the emergency release hole on the right side
of the device and turn it clockwise.
(Before activating emergency open, switch off the device
and wait for the rotor to stop.)
Allow a Safety Clearance of 30 cmEmergency Lid open
AL15-12 12 x 15 ml / Max. 4k (Rotor ID : 3)
AL15-24 24 x 15 ml / Max. 4k (Rotor ID : 4)
S50-6 6 x 50 ml Round / Max. 4k (Rotor ID : 2)
S85-4 4 x 85 ml Round / Max. 4k (Rotor ID : 1)
30 cm
30 cm
30 cm
Swing-out RotorsFixed-angle Rotors
500VA
220~240V
50/60Hz
Rev.0
Proudly made by Jiyoung Shim, Hyewon Jeong
Order & Inquiry l [phone] l [email protected] l www.ihanil.com
Service l [phone] l [email protected]
Switch off the device after use.
Unplug the power plug before
cleaning or unused for a long
period of time.
Check the wall outlet is
earth grounded, surge-
protected andcan supply
enough power.
Connect the device to voltage sources
which correspond to the power require-
ments on the label attached to the device.
Switch Off the DeviceGrounded OutletCheck the Line Voltage
Maintenance
Electrical Safety
Rotor
Cautions For Use
Before Operation
After Operation