Hanil HyperVAC HVC-2124 User manual

HyperVAC
HVC-2124 / HVC-2200
Product Model Name :
Date of Purchase :
User Manual

HyperVAC
HVC-2124/HVC-2200
© 2018 Hanil Scienti󽗉c Inc.
The appearance or speci󽗉cations of the device is subject to partial change for improvement.
If youhaveany questions,contactour TechnicalSupport Center.
[phone] /[e-mail]
www.ihanil.com
Manufacturer: Hanil Scientific Inc.
B2 & 5F, 16 Arayukro Gochon-eup, Gimpo-si, Gyeonggi-do, 10136, Republic of Korea
UM-H_HyperVAC(E)(Rev.4), 2023.11.27

INDEX
1. Safety Precautions ---------------------------------- 4
1.1 Using this manual - 4
1.2 Safety Labels on the Device - 4
1.3 Safety Precautions - 5
2. Product Description -------------------------------- 7
2.1 Product Description - 7
2.2 Delivery Package - 8
2.3 Technical Speci󽗉cations - 9
3. Installation -------------------------------------------- 10
3.1 Unpacking - 10
3.2 Connection with Supplying Device - 10
3.3 Switching On the Device - 11
3.4 Opening the Lid - 11
3.5 Emergency Lid Release - 12
3.6 Installing/Removing the Rotor - 13
3.7 Positioning of Sample Tubes - 14
4. Operation ---------------------------------------------- 15
4.1 Key Functions of Control Panel - 15
4.2 Setting the RPM - 17
4.3 Setting the Time - 17
4.4 Setting the Temperature - 17
4.5 Saving a Program - 18
4.6 Calling up a Program -18
4.7 Start / Stop - 18
4.8 Operation Sequence - 19
4.9 Manaul Operation - 20
5. Maintenance ------------------------------------------ 21
5.1 Outer Part of the Device - 21
5.2 Chamber - 21
5.3 Motor Shaft - 21
5.4 Rotor - 22
5.5 Transportation of Device - 22
6. Troubleshooting ------------------------------------- 23
6.1 Possible Problems - 23
6.2 Error Codes - 24
7. Rotors & Accessories -------------------------------- 26
The appearance or speci󽗉cations of the device is subject to partial change for improvement.

www.ihanil.com
4 / 29
1. Safety Precautions
This manual is for the users who operate the device for the 󽗉rst time.
This manual provides information on the detailed instructions, precaution, troubleshooting
and maintenance care.
Keep this manual nearby for future reference.
The labels on the device represent safety instructions and directions.
1.1 Using this manual
1.2 Safety Labels on the Device
Indicate a hole
for manual lid opening
in case of emergency
Attention and warning
for electric shock
Mark indicating
danger and warning
Attention and warning
for rotor coupling
Mark indicating
Biohazard warning
Mark indicating
earth grounding

Technical Support : [phone] / [email protected]om 5/29
1. Safety Precautions
Before using the device, please read this operation manual to ensure correct usage. Incorrect
handling of the device may possibly result in personal injury or physical damage on the
device or its accessories.
1. ALWAYS locate the device on a 󽗊at, rigid and stable table capable of withstanding the
weight of the device and its spinning operation.
2. ALWAYS make a safety zone of 30 cm around the Device to indicate that neither
hazardous materials nor persons should be permitted within the area during operation.
▶ ALWAYS position the device with enough space on each side of device to ensure
proper air circulation.
3. ALWAYS install the device within a temperature and humidity controlled environment
(permissible ambient temperature: 5 ~ 35 °C, relative humidity: 30 ~ 85 %, atmospheric
pressure: 500 ~ 1,060 hPa).
4. Before connecting the power, check the rated voltage.
5. Should not use unapproved rotors and accessories.
▶ Only use rotors from Hanil Scienti󽗉c Inc. with appropriate centrifugal tubes to embrace
sample containers tightly enough inside rotors.
6. Before operating the device, check if the rotor is securely fastened.
▶ Should operate the device with a rotor properly installed and secured to the motor
shaft.
7. Do not stop the rotor by hands during the device is running.
8. Emergency lid release should be performed only when rotor is completely stopped.
9. ALWAYS load the tubes symmetrically with evenly weighted samples to avoid rotor
imbalance. If necessary, use the water blank to counterbalance the unpaired sample.
10. The operation speed should not exceed the highest value of the individual guaranteed
g-forces of each centrifuge, rotor, sleeves and sample container, especially the guaranteed
g-force of sample container should not be neglected.
11. ALWAYS disconnect the power supply prior to maintenance and service to avoid electrical
shock.
1.3 Safety Precautions

www.ihanil.com
6 / 29
12. ALWAYS use proven disinfection procedures after centrifuging biohazardous materials.
13. Should not centrifuge 󽗊ammable, toxic, radioactive or explosive materials.
14. When it is necessary to use toxic or radioactive materials or pathogenic micro-organisms
which belong to the Risk Group II of WHO: “Laboratory Bio-Safety Manual,” should follow
national regulations.
- Do not place dangerous materials within 30 cm distance around the device.
- Use the emergency lid release function only when the lid button on the
control panel is dumb under the condition of complete stop of rotor running.
- Never try to open or move the device if it is not completely stopped.
- If the power input is more than +/-10% of the recommended voltage or
󽗊uctuates frequently, it may cause malfunction of the device and often
result in serious damage.
- Install the device at the place without any kinds of corrosive gases.
1. Safety Precautions
1.3 Safety Precautions

Technical Support : [phone] / [email protected]om 7/29
2. Product Description
2.1 Product Description
[HVC-2124]
[HVC-2200]

www.ihanil.com
8 / 29
2. Product Description
2.2 Delivery Package
· Check all parts for damage that may have occurred during transportation.
· Check the delivery for completeness.
- Hyper VAC 2124/2200
- AC Power cable
- Emergency release tool

Technical Support : [phone] / [email protected]om 9/29
2. Product Description
2.3 Technical Speci󽗉ations
HVC-2124 HVC-2200
Max. RPM 200 ~ 2,000 RPM 200 ~ 2,000 RPM
Max. Capacity
120 x 1.5 / 2.0 ml microtubes
or
48 x 1.5 / 2.0 ml + 76 x 0.5 ml
microtubes
200 x 1.5 / 2.0 ml microtubes
12 x 50 mL
Auto Start / Stop Yes Yes
Chamber Heating
Temperature Range OFF, 4 ~ �5 ℃*
Vacuum Pressure 1 ~ 1,013 mbar 1 ~ 1,013 mbar
Operating Time
< 23 hr 59 min or continuous
Default value: 0 h 0 m
(continuous)
< 23 hr 59 min or continuous
Default value: 0 h 0 m
(continuous)
Centrifuge Dimension
(W x D x H, mm) 375 x 445 x 252 475 x 560 x 350
Weight (kg) 22.5 (without Rotor) 37 (without Rotor)
Power Requirements 220~230V AC, 50/60Hz 20~230V AC, 50/60Hz
OFF, 4 ~ �5 ℃*
**Temperature setting can be turned off or set from 4 to 65℃.
If you set it lower than room temperature, the set temperature cannot be reached because there is no
refrigeration function.
If you set the temperature higher than room temperature, the heating function operates to reach at the set
temperature.

www.ihanil.com
10/29
3. Installation
3.1 Unpacking
3.2 Connection with Supplying Device
1. Open the box and lift out the device carefully.
2. The system should be horizontally lifted up on the 󽗊at table.
3. Insert the Emergency Lid Release Tool into ‘Opening for Emergency Lid Release’ on the left
side of the main body.
▶ Remove the protection material inside the main body; Vacuum Concentrator series are
delivered with the basic rotor mounted, and the protection material is inside the main body
for rotor protection.
4. It is now ready for installation.
The following pictures guide a way for connecting a Drip catcher kit with Centrifuge and
Vacuum Pump.
Connection to
Vacuum Pump
Connection to
Centrifuge
Right Connection
Way of Pipe

Technical Support : [phone] / [email protected]om 11/29
3. Installation
3.3 Switching On the Device
3.4 Opening the Lid
1. After connecting the AC Power cord to the mains power on the right back of the device,
turn on the Earth Leakage Circuit Breaker.
▶ Check the power on.
2. Turn on the main power on the right side of the device.
1. For opening lid, press the button.
- Should press the button when the lid is closed (Lid LED turns o󽗈).
- Close the lid until hearing clank shut.
- When the lid is open, the lid LED turns on.
- The lid is not released while the device is running.
(With the vacuum pump connected, the lid is released only when the vacuum
is released.)
- If the lid is opened, the device cannot be operated even with pressing the
button.
- Power Failure: If there is any power failure during operation, lid is not open
with the button. Lid can be released only when the operation is
completely
stopped and the power is on. If you want to release the lid in the event of a
power failure, refer to ‘3-5. Emergency Lid Release.

www.ihanil.com
12/29
3. Installation
3.5 Emergency Lid Release
For emergency lid release, you can use the Emergency Lid Release Tool only when the
device is completely stopped.
The lid can be unlocked manually with the Emergency Lid Release Tool through the Opening
for Emergency Lid Release.
1. Find the Opening for Emergency Lid Release on left side of the device.
2. Insert Emergency Lid Release Tool into the opening and push it until the lid is released.
- Manual lid opening should be performed only when spinning is
completely stopped. Otherwise, harmful damage can be accompanied.
- After opening the lid manually, it is recommended to wait until the
main power turns back on.

Technical Support : [phone] / [email protected]om 13/29
3. Installation
3.6 Installing/Removing the Rotor
1. Before installing a rotor, clean the motor shaft and chamber with soft dry towel.
2. Load a rotor into the motor shaft. Lock it with the Locking Nut.
- To install the rotor: Rotate the locking nut clockwise until tightly assembled.
- To remove the rotor: Rotate the locking nut counterclockwise.
Locking nut

www.ihanil.com
14/29
3. Installation
3.7 Positioning of Sample Tubes
1. Before loading sample tubes, check the water drop or dirt in the rotor hole or inner sleeve.
▶ If you 󽗉nd water drops or dirt in the rotor or inner sleeve, remove it with soft dry cloth.
2. Tubes should be placed in the rotor with equal amount of samples at symmetrical
positions.
▶ Only use appropriate centrifugal tubes and do not exceed the speed beyond the max
g-force allowed for the tubes.
- If it is hard to make balance with the samples, please employ control
tubes. Otherwise, it may bring about noise or vibration, which may lead
to damaging the device.
Correct Arrangement
Wrong Usage of Tubes
Di󽗈erent Caps Di󽗈erent DensityDi󽗈erent Volume Di󽗈erent Tubes

Technical Support : [phone] / [email protected]om 15/29
4. Operation
4.1 Key Functions of Control Panel
①Use to set the of RPM (200 ~ 2,000 rpm)
②Use to set time, available range up to 23 hr 59 min or continuous
③Use to set temperature (RT ~60 ℃) . Display the set temperature while idle,
and actual temperature during operation.
④Use to display the vacuum pressure for checking the vacuum level
⑤Use to save the set values or recall the saved parameters
(Saving capacity max. 100 memories).
⑥Use to con󽗉rm the parameter setting
/ Check the preset values during operation
⑦Use to start or stop operation
⑧Use to open the device lid. Only activated when the vacuum is released.
⑨
Use for (1) manual on/off of vacuum pump. It is only activated while the
device is idle. And use to (2) move to Sub Display from Main Display.
Refer to 6-1-2. Sub Display for more detailed information.
⑩Use to start operation at the set chamber temperature. PRE-HEAT LED blinks
during the setting and is kept on when the setting is completed.
[Main Display]
① ② ③ ④ ⑤ ⑥ ⑦
Up
Down
⑨ ⑩
⑧

www.ihanil.com
16/29
4. Operation
4.1 Key Functions of Control Panel
[Sub Display]
Sub Display appears upon the button after setting the operating conditions.
- Sub Display function is for manual ON/OFF of vacuum pump. But it can be used only
when the machine is not operating.
- Normally, adjustment of the Sub Display is not used for operation but for Emergency Lid
Release in any emergency conditions. The detailed method & sequence for the Emergency
Lid Release are stated in section 6-7-3.
- If you press the button after setting the Sub Display function, you can go to the Main
Display again.
- Function LED blinks during the Sub Display setting and is kept on when the setting is
completed.

Technical Support : [phone] / [email protected]om 17/29
4. Operation
4.2 Setting the RPM
4.3 Setting the Time
4.4 Setting the Temperature
1. Press the button once.
- RPM mode
- RPM LED 󽗊ickers on the display window.
2. Press the or button to change input value and then press the button
to complete the setting.
1. Press the button once.
- The set time LED 󽗊ickers with beeping sound.
2. Press the or button to change input value and then press the button
to complete the setting.
- Time is counted down after starting centrifugation.
1. Press the button once.
2. Press the or button to change input value and then press the button
to complete the setting.
▶ Speed setting unit (display unit): 10 rpm (1 rpm)
▶ Speed setting range: (200 ~ 2,000 rpm)
▶ Time setting range: 23 hr 59 min or continuous
▶Temp setting unit & display unit: 1 °C
▶Temp setting range: 4 ~�5 ℃
▶If you want to turn off the temperature setting, press the button to until OFF appears
Temperature Pull-up time(2000rpm, Vacuum on, RT)
-RT->30°C : 20min
-RT->45°C : 60min
-RT->65°C : 90min
★While pull-up time, the temperature can be displayed higher than the actual internal
temperature of chamber

www.ihanil.com
18/29
1. Set parameters. (Refer to 4-2 ~ 4-4.)
2. Press the button longer than 3 seconds.
- Check the message of “PROGRAM SAVE: ##” on the display window.
3. Press the or buttons to change input Program number.
- Save up to 100 programs. (Program numbers from 0 to 99)
4. Press the button to complete the saving.
4. Operation
4.5 Saving a Program
4.6 Calling up a Program
4.7 Start / Stop
1. To recall the saved program, press the button shortly (less than 1 sec.).
- Check the message of “PROGRAM CALL: ##” on the display window.
3. Press the or buttons to to select program number you want to call up
and then press the button.
[Start]
1. After setting RPM, Time and Temp., press the button.
- During running, a ‘Start LED’ is turned on.
- The device runs only when the lid is closed.
[Stop]
1. You can stop the operation by pressing the button.

Technical Support : [phone] / [email protected]om 19/29
[Detailed Sequences for Operation]
1. Fill the chamber of Drip Catcher kit with ice.
2. Turn on the centrifuge and the vacuum pump.
3. Set the parameters according to your preferences. (RPM / TIME / TEMP)
4. Press the button then or button to switch the status of the vacuum pump.
Press the button upon setting each function. Normally, you don’t need to adjust the
values for these functions.
5. Press the button to start operation with your set values.
☞ If you set your speed above 1,000 rpm, the vacuum pump starts to operate at 1,000 rpm.
If you set it below 1,000 rpm, the vacuum pump starts to operate at your set RPM.
☞ Operation starts before the chamber reaches to the set temperature. If you want to start
the operation at your set temperature, you can use the PRE-HEAT function. Press the
button before pressing the button. Then the operation starts after reaching your set
temperature. LED blinks while setting and is kept on upon the completion of the setting.
Press the button to start operation.
6. If you want to stop the operation, press the button.
- Vacuum pump stops.
- Vacuum Release function is activated and the releasing is completed. Function LED blinks
during the release and is kept on upon the completion of the release.
- With the vacuum released, alarm beeps and Lid LED blinks for 5 seconds when the rotor
completely stops.
7. To open the lid, press the button after the vacuum release. Then lid lock is released
for 5 seconds with the Lid LED on, and you may open it within the time.
4. Operation
4.8 Operation Sequence

www.ihanil.com
20/29
4. Operation
4.9 Manaul Operation
If you need to adjust the function of vacuum pump, to release it or execute emergency open,
you can use manual operation.
1. Turn on the main power.
2. Press the button.
3. Check the display. (Default: Vacuum pump: OFF / Release: OFF)
4. Press the button and then press the or buttons to set the status of
the vacuum pump. You can switch on or o󽗈 vacuum pump and release the vacuum on your
need. You need to press the button after setting each function.
5. If you want to execute the emergency lid open, the release has to be set as ‘ON’.
6. When the vacuum release is completed, alarm beeps and Lid LED blinks for 5 seconds.
7. Press the button and open the lid within 5 seconds while the Lid LED blinks.
4.8 Operation Sequence
[Operating Status for Each Part (VacPump / Release / Heater)]
Power ON
(Start status: default setting)
VacPump Release Heater
OFF OFF OFF
Setting Temperature and Running
Device (~20 min.)
VacPump Release Heater
OFF OFF OFF
Until reaching the set RPM (Refer to
VacPump Release Heater
OFF OFF ON
After reaching the set RPM or 1,000 rpm
VacPump Release Heater
ON OFF ON
Press the STOP button.
VacPump Release Heater
OFF ON OFF
After completing the Stop –Return to the
Start Status (default setting)
VacPump Release Heater
OFF OFF OFF