Hanil ARA Smart 6 User manual

ARA Smart 6

ARA Smart 6
Research Use Only
Copyrightⓒ 2019 Hanil Scienti󽗉c Inc. All rights reserved.
Contact Us
If you have any questions, contact Hanil Scienti󽗉c Inc.
[email protected]om / [email protected]om

1. Safety ----------------------- 4
1-1. Caution: Installation----- 4
1-2. Caution: Use ------------- 5
2. Intended Use ------------------ 5
3. Product overview --------------- 6
4. Technical specifications ------- 7
5. Installaion/Operation --------- 8
5-1. Power connection ------ 8
5-2. Operation -------------- 9
6. Troubleshooting ----------- 10
CONTENTS
The appearance or specifications of the device is subject to partial change
for improvement.
Copyrightⓒ 2019 Hanil Scienti󽗉c Inc. All rights reserved.
Contact Us
If you have any questions, contact Hanil Scienti󽗉c Inc.
[email protected]om / [email protected]om

4A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
1. Safety
Follow precautions and all the safety requirements described on this user
manual to prevent any damages and failure of equipment.
1-1. Caution: Installation
1. The device must be kept in a dry and well-ventilated room.
2. According to IEC61010-2-020 maintain a 30cm “clearance envelope” around the device
while the rotor is spinning.
3. Do not operate the device in areas where work is completed with explosice substances
4. Connect the device to voltage sources which correspond to the electrical requirements
on the label attached to the device.
5. Do not install the device at a place with high voltage regulation.
(Allowable voltage regulation limits : ± 10 %)
6. Use sockets with a protective earth conductor and suitable power cord.

5
A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
1. The device should be installed on flat surface to maintain level.
2. Always keep the device clean and dry
3. The balancing work of samples should be done in advance before operation.
4. Do not move the device or open the lid during operation.
6. Do not attempt to slow or stop the spinning rotor by hand.
7. Do not spill liquid on the device. If you spill liquid, shut off the power supply and unplug
the powercord from the outlet and contact Hanil Technical Support Team.
8. Do not block vents.
9. Do not drop or subject the device to severe impacts
10. Caution when handling the AC/DC adaptor.
- Do not bend or pull the AC/DC adaptor.
- Use the AC/DC adaptor in dry room, away from heat and humidity.
- Unplug the power plug before cleaning or left unused for a long period of
time.
2. Intended Use
The Smart6 centrifuge is used for the separation of components.
In order to increase the usability, it is possible to use continuous mode or short mode
only by switch operation.
1-2. Caution: Use

6A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
3. Product overview
Lid open button
DC adaptor
Connector
Continuous & Normal Switch
Operation mode switch
Lid
Closing the lid: Start the centrifugation
Opening the lid: Stop the centrifugation
Short Mode (S)
Operate after closing the lid
Continuous Mode(C)
Stop the centrifugation after 15 min. of centrifugation

7
A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
4. Technical Specifications
Max. RPM 6,500 RPM
Max. RCF 2,234 x g
Tube capacity 6 x 1.5/2.0 mL, 2 x 8-tube PCR Strips
Accel 4 sec
Decel 2 sec
Weight 0.65 kg
Power supply DC 12V 2A , AC100~240V, 50/60Hz
Dimension
150W x 150D x 103H, mm
Cat. No.
AC-Smart 6
* Delivery package
ARA SmarT 6
USERMANUAL
Manual
Main body
AC/DC adaptor
Wrench
(For rotor locking)
Rotor Cap Nut
Angle Rotor
(1.5/2.0 mL x 6-hole)
Rotor
(2-PCR Strips)

8A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
5. Installtion / Operation
5-1. Power connection
Check the delivery for completeness.
The device should be installed on flat surface to maintain level.
Do not bend or pull the AC/DC adaptor.
Keep this manual near the device at all times.
1. Connect the power cable to the power socket on the back side of the device
and plug the cord into the outlet.
2. A beep sounds when the power is connected.
1. Connect the power cable to the power socket on the back side of the device
and plug the cord into the outlet.
2. A beep sounds when the power is connected.

9
A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
Do not open the lid until operation is completely stopped as
it will decelerate immediately when the lid is opened during
operation.
- Press the lid open button.
3. Opening the lid
2. Starting/Stopping the centrifugation
Short Mode (S)
- When the lid is closed, centrifutaion starts.
Continuous Mode (C)
- Operataion stops after 15 min. of operation.
5-2. Operation
1. Installing the rotor
- Load the rotor vertically onto the motor shaft.
- Put the cap nut on the center of the rotor and
turn the wrench clockwise untill it secured.

10 A/S Inquiry : [phone] / [email protected]
USER MANUAL MINI CENTRIFUGE
6. Troubleshooting
The device can not be started
1. Power failure
→ Check the mains connection.
2. AC adaptor defect
→ Check the output DC volt of the adapter using a multimeter
3. Lid sensor failure
→ Contact Hanil Technical Support Team.
4. If the beep does not sound right after connecting the power supply,
contact Hanil Technical Support Team.
[phone] / [email protected]

im-ara.com
OMM7PDEN1901-C