Hanil T05R User manual

Quick Guide T05R
Cat. No. : T05R
Serial No. Installation Date
Setting RPM / RCF, Time, ACC / DEC
Touch
RPM / RCF,
Time, ACC / DEC
Touch the
Enter button
Touch the
Enter button
Set the desired
values by touching
the numeric keys.
Program SAVE / CALL Fast Cool
Touch once : CALL / Touch twice : SAVE
Touch the Save or Call button.→
Touch the numeric buttons to set
the desired program number
Touch and hold the Fast cool button
Max.
RPM / RCF
Fixed-angle 5,000 rpm / 3,983 xg
Swing-Out 5,000 rpm / 4,218 xg
Program 100
Time Control Pulse, timed < 100 hr or continuous
ACC/DEC 9 (Max 9) / 10 (Natural 0)
Display & Control
Display
Status of RPM, RCF,
Time, Temperature,
ACC, DEC, Running,
Lid open/close
At set Speed
On : Counts the time at set speed / O : Counts the time from
startingTouch more than 2 sec. : Repeat time of end alarm
(time : 0 ~ 99, 0 : silent)
Start / Stop
Temp / Fast Cool
Touch for more than 2 seconds to reach
rapid refrigeration up to setting temp
Lid Open
LED On : Lid open
LED O : Lid closed
Setting Time
End Alarm
Sound volume
(level : 0 ~ 10,
0 : silent)
Setting
ACC / DEC
Program SAVE / CALL
Touch once : CALL / Touch
Touch twice : SAVE (up to 100)
Setting Speed
Touch once : RPM
Touch twice : RCF
Key Lock
LED On : Key lock
LED O : Key unlock
Pulse

Before Operation
After Operation
Check the rotor is rmly tightened onto
the motor shaft.
Check the Rotor Locking
After relocating the device or loading the rotor,
balance them by using a leveler. If necessary, level
the device by adjusting the‘Leveling foot’on the
bottom of the device.
Balancing the Centrifuge and Rotor
Cautions For Use
After cleaning, lubricate
bucket grooves, pivots of
swing-bucket rotors and
threads of the angle rotors
using the lubricant.
Wipe up the moisture in the
chamber with a dry cloth after
use. Keep the lid open when not
in use.
Clean the chamber and
rotor by wiping with a cloth
soaked in mild detergent and
dry completely.
Care of Swing-Out Rotor Keep the Chamber DryCleaning
Check the rotor, buckets and tubes are
free of scratch and crack before operation.
Check the Accessories for Abnormalities
Load tubes symmetrically into the
rotor with identical amount.
Load Tubes Symmetrically
A-15-24
A-50c-10
A-50-10
S-mw-2
S-15-6
S-50-4
S-100-4
24 x 15 mL / Max. 5k
10 x 50 mL Conical / Max. 5k
10 x 50 mL / Max. 4k
2 x 4 MTP / Max. 4k
6 x 2 x 15 mL / Max. 4.4k
4 x 50 mL / Max. 5k
4 x 100 mL / Max. 4.5k
Rotor
Electrical Safety
Switch o the device after
use. Unplug the power plug
before cleaning or unused for
a long period of time.
Check the wall outlet
is earth grounded,
surge-protected andcan
supply enough power.
Switch O the DeviceGrounded OutletCheck the Line Voltage
Maintenance
If the centrifuge lid cannot be opened, insert
the provided T-wrench into the emergency
release hole on the left side of the device and
turn it clockwise. (Before activating
emergency open, switch o the device and
wait for the rotor to stop.)
Emergency Lid Open
Swing-out RotorsFixed-angle Rotors
Connect the device to voltage
sources which correspond to
the electrical requirements on
the label attached to the device.
900VA
220V 50/60Hz
(110V Optional)
Keep a safety clearance of
30 cm around the centrifuge
during operation.
Empty the CondensateKeep a Safety Clearance
Empty the condensate
regularly by removing the
drain cap on the left side of
the device
30 cm
30 cm
30 cm
HI-QG-T05R(E)(Rev.1)
Quick Guide T05R
Cat. No. : T05R
Order & Inquiry l [phone] l [e-mail] l www.ihanil.com
Service l [phone] l [email protected]