Hanil Component wR User manual

Quick Guide Component wR
Cat. No. : CP-wR
Display & Control Panel
PULSE
xg
VIEW
SETTINGS
Start Stop Lid Open
Max. RPM : 4,500 rpm
Max. RCF : 5,096 xg
Display Screen
Status of RPM / RCF / Time /
Temperature / Rotor ID /
ACC / DEC / Program
Setting Speed
Press once : Setting RPM
Press twice : Setting RCF
Setting Time
Up < 100 hr
Continuous run (00:00)
View Settings
Verifying the setting
parameters during
centrifugation
Setting Temperature
Setting temperature ( -20℃ ~ 40℃)
Setting temp. limit
Pulse
Program Save / Call
Saving a program
(up to 100)
Calling up a program
Setting the Rotor ID manually
Enter the rotor ID. manually, when
rotor id is not identified automatically
Press the
Pulse button
Enter the desired speed
(See ‘Setting Run Parameters’)
Saving / Calling Up a Program
Press a parameter
to be changed
Press the
Enter button
Enter the desired values
on the keypad
Enter the desired
program number on
the keypad
Press the
Save or call button
Setting Run Parameters
(RPM / RCF / Time / Temperature / ACC / DEC)
Press the
Enter button
Press the
Temp. limit button
Press the
Enter button
Temperature range that stops operation when the temperature
is lower or higher than the set temperature.
Enter the desired
temperature range
on the keypad
Setting Temp. Limit
Pulse
After reaching the set
speed, the centrifugation
is decelated and stopped
Setting ACC / DEC Rate
ACC (0 ~ 9 steps, Max.9)
DEC (0 ~ 9 steps, Natural DEC.0)
Serial No. Installation Date
2 31
5 64
8 97
0
±

Connect the device to voltage
sources, which correspond to the
electrical requirements on the label
attached to the device.
Check the wall outlet is earth-
grounded, surge-protected and
can supply enough power.
Connect the power cable to the
distribution box, or install the plug
and socket that are packed with
the device.
Switch off the device after use.
Unplug the power plug before
cleaning or unused for a long
period of time.
Check the Line Voltage Grounded Outlet Power Connection Switch Off the Device
Quick Guide Component wR
Cat. No. : CP-wR
WS750-6 6 x 750 mL / Max. 4.5k
30 cm
30 cm
30 cm
Allow a safety clearance of
30 cm around the centrifuge
during operation and
storage.
Care of Swing-Out
Rotor
Remove Dust Empty the Condensation
Water
Allow a Safety Clearance
of 30 cm
Emergency Lid Open
If the centrifuge lid cannot be opened,
insert the provided T-wrench into the
emergency release hole on the right side
of the device and press it. (Before activat-
ing emergency open, switch off the
device and wait for the rotor to stop.)
Spread the grease lightly
on the bucket where it
contacts the rotor and the
pivot.
Remove any dust from the
ventilation slits on the right
side of the device. Empty the condensation water
regularly by removing the
drain cap on the left side of the
device.
3.0KVA
220~240V 50/60Hz
Maintenance
Electrical Safety
Rotors
Cautions for Use
Before Operation After Operation
Check the rotor, buckets and tubes are free
of scratch and crack before operation.
Check the Accessories for Abnormalities
After relocating the device or loading the rotor,
balance them by using a leveler. If necessary,
level the device by adjusting the ‘Leveling foot’
on the bottom of the device.
Balancing the Centrifuge and Rotor
Load tubes symmetrically into the rotor
with identical amount.
Load Tubes Symmetrically
Place the lid on the wind shield rotor before
centrifugation.
Check the Lid
Wipe up the moisture in the chamber with a
dry cloth after use. Keep the lid open when
not in use.
Clean the chamber and rotor by wiping with
a cloth soaked in mild detergent and dry
completely.
Keep the Chamber Dry
Cleaning
Rev.1
Proudly made by Jiyoung Shim, Hyewon Jeong
Order & Inquiry l [phone] l [email protected] l www.ihanil.com
Service l [phone] l [email protected]