Harbor Breeze 42224 User manual

9689 • 090120 1
ELMHURST CEILING FAN
Owner’s Manual
Model #42224
Item #2599769
To obtain service, please contact the Service Department:
1-877-706-3267, 8 a.m. - 5 p.m. Central, Monday - Friday.

2
PACKAGE CONTENTS
1. Mounting Bracket
2. Canopy
3. Mounting Bracket Screw
(x4)
4. Canopy Cover
5. Downrod
6. Downrod Pin
7. Downrod Clip
8. Yoke Cover
9. Set Screw (x2)
10. Motor Assembly
11. Motor Screw (x6)
12. Fitter Plate
13. Fitter Plate Screw (x4)
14. Light Pan
15. Light Pan Screw (x3)
16. Cage Screw (x4)
17. Light Kit
18. Glass Bowl
19. Light Cage
20. Blade (x3)
21. Blade Arm (x3)
22. Remote Pack
23. Hardware Kit
24. Owner’s Manual
25. Blade Screw (x9)
26. Blade Washer (x9)
27. Wire Connector (x4)
Unpack your fan and check the contents. You should
have the following items:
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Some extra hardware has been included. The quantity
listed above is the number required for installation.
HARDWARE CONTENTS
TOOLS REQUIRED (not included)
Tools required for assembly: Electrical tape, Phillips Screwdriver, Pliers, Safety Glasses, Step Ladder, Wire Cutters
and Wire Strippers
Helpful Tools: AC Tester Light, Tape Measure, and Wiring Handbook
272625
Hardware Kit
Owner’s
Manual
12
24
23
22
11
9
8
10
7
6
5
4
15
19
21
20
17
18
13
3
14
16
2
1

3
A. 16.46 in. B. 10.82 in. C. 9.53 in. D. 5.13 in.
DIMENSION REFERENCE
D
CB
A
MOUNTING OPTIONS
Choose one of the following mounting options:
Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer
downrod (not included).
Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary
to ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is
not steeper than 10°.
Two Mounting Options
Downrod Mount Angled Ceiling Mount (Up to 10 degrees)

4
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE
FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing
the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.
The safeguards provided by these safety instructions and by the separate installation instructions are not
meant to cover all possible conditions and situations that may occur. It must be understood that common
sense, caution and care are factors which can not be built into this product. These factors must be supplied
by the person(s) installing, caring for and operating the fan.
The fan weight is Net Weight: 16.78 lb (7,61 kg). Be sure the outlet box (not included) is securely attached
to the building structure and is marked “Acceptable For Fan Support”. Failure to do so can result in serious
injury.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver
--Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Please note changes or modications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
HKC-US
3350 Player’s Club Parkway, #225
Memphis, TN 38125
1-877-706-3267
SAFETY INSTRUCTIONS
CAUTION:

WARNING:
To avoid risk of electric shock, be sure to shut o power at the main fuse or circuit breaker box before
installing or servicing this xture. Turning o the electrical power by using the light switch is not
sucient to prevent electrical shock.
To reduce the risk of injury, install the fan so that the blades are at least 7 feet (2.1 Meters) above the
oor and at least 18 inches (0.5 Meters) from the tip of the blades to the wall.
To reduce the risk of re, electric shock, or personal injury, mount to outlet box marked “acceptable for
fan support” and use mounting screws provided with the outlet box.
The installation has to be in accordance with the national electrical code, ANSI/NFPA 70-1999 and
local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a
qualied licensed electrician.
Using a full-range dimmer switch to control fan speed will cause a loud humming noise from the fan. To
reduce the risk of re or electric shock, do NOT use a full-range dimmer switch to control the fan speed.
SAFETY INSTRUCTIONS
5

D
6
ASSEMBLY INSTRUCTIONS
1
3
2. Remove the mounting bracket by removing the two
mounting bracket screws from the round holes in the
canopy. Then loosen the other two mounting bracket
screws from the J-shaped slots. Retain the mounting
bracket screws for later.
3. Install the mounting bracket to the outlet box (not
included) using the screws and washers provided with
the outlet box.
WARNING: To reduce the risk of re, electric shock,
or personal injury, mount to the outlet box marked
“acceptable for fan support” and use the mounting
screws and washers provided with the outlet box.
Angled Ceiling Mount
Downrod Mount
Mounting Bracket Screw
2
3
4
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
DANGER: Failure to disconnect the power supply prior to
installation may result in serious injury or death.
4. Remove the six motor screws from the underside of
the motor assembly and save for blade arm installation.
Motor Screw Motor Assembly

7
Tab
Slot
Downrod
Receiver
8. Install the ball end of the downrod into the opening of
mounting bracket. Rotate the downrod until the tab in the
mounting bracket is seated in the slot in the downrod ball.
WARNING: The fan and/or downrod should not rotate in
the mounting bracket, if installed correctly. Failure to align
the slot in the downrod ball with the tab on the mounting
bracket may result in fan falling causing serious injury or
death.
Insert the receiver from remote pack into the mounting
bracket with antenna end rst and the at side facing the
ceiling. Note: The receiver will rest on the downrod.
Note: There is an adhesive sticker on one of the antennas
connected to the receiver. For best results, stick the
antenna to the ceiling.
Downrod Pin
Downrod Clip
Yoke
Downrod
Set Screw
7. Slide the downrod into the yoke of the motor assembly,
align the holes, then re-install the downrod pin and
downrod clip. Secure with the two set screws and slide
the yoke cover down until it rests on top of the motor
assembly.
Note: With wiring extending out of the downrod,
measure 8 inches of lead wire and cut the excess wire with
wire cutters (not included). Then strip 1/2” of insulation
from the end of each wire.
7
6
ASSEMBLY INSTRUCTIONS
Mounting
Bracket
6. Insert the downrod through the canopy and yoke
cover. Feed the wires from the fan through the downrod.
Canopy
Yoke Cover
Downrod
Yoke
8
Downrod
Clip
Downrod
Pin
Set Screw
Yoke
5. Remove the downrod clip and downrod pin from the
downrod. Then loosen but do not remove the two set
screws in the yoke at the top of the motor assembly.
5

8
ASSEMBLY INSTRUCTIONS
Black (hot/power)
Push-in Connector
Wire Connector
White (neutral)
Bare/Green
(ground)
White
White
Black
Blue
Blue
Black
Green
Green
Receiver
Black
White
Canopy J-slot
Round
Hole
Mounting Bracket Screw
10
11
9
Blade Screw
Blade Washer
Blade
Blade Arm
10. Raise the canopy, ensure the two mounting bracket
screws are aligned with the J-shaped slots in the canopy.
Then turn the canopy in a clockwise direction until the
mounting bracket screws are completely engaged in
the J-shaped slots. Install the two previously removed
mounting bracket screws in the round holes. Securely
tighten all mounting bracket screws.
11. Partially insert the blade screws along with the blade
washers through the blade and into the blade arm.
Tighten each blade screw with a Phillips screwdriver (not
included), starting with the one in the middle.
Repeat this step for the remaining blades and blade arms.
9. Use wire connectors and push-in connectors to connect
the receiver and fan wires to the supply wires from outlet
box according to the wiring diagram and the following
instructions:
• Connect the Green wires from the fan and the mounting
bracket to the Bare/Green (ground) supply wire.
• Connect the Blue wire (FOR LIGHT) from the receiver to
the Blue fan wire.
• Connect the Black wire (TO MOTOR L) from the receiver to
the Black fan wire.
• Connect the White wire (TO MOTOR N) from the receiver
to the White fan wire.
• Push the Black (Hot/Power) supply wire into the empty
wire hole in push-in wire connector preassembled to the
Black wire (AC IN L).
• Push the White (neutral) supply wire into the empty wire
hole in push-in wire connector preassembled to the White
wire (AC IN N).
Important: After the connections have been made, the
connected wires should be turned upward and pushed
carefully up into the outlet box. Place the black and white
wire connections on opposite sides of the outlet box.

9
ASSEMBLY INSTRUCTIONS
14. Remove one of the three light pan screws from the
light pan and loosen the other two but do not remove.
Connect the 9-pin connectors from the light pan to the
9-pin connectors from the light kit. Lift the two keyhole
slots in the light kit over the two loosened light pan
screws and turn in a clockwise direction. Then, use the
previously removed light pan screw to secure the light kit
to the light pan. Tighten all screws.
Light Kit
Light Pan Screw
Light Pan
9-pin
Connector
Glass Bowl
Light Kit
15. Attach the glass bowl to the light kit by twisting the
glass bowl tightly in a clockwise direction until it is secure.
CAUTION: Avoid cross-threading the glass during
installation. Improper installation could cause the glass
bowl to be dicult to remove or fall, which could cause
serious injury.
13. Remove one of the four tter plate screws
preassembled to the tter plate and loosen the other three
but do not remove. Feed the 9-pin connector through
center hole in light pan. Align the keyhole slots in the light
pan with the loosened screws in the tter plate. Turn light
pan clockwise and replace the previously removed tter
plate screw. Tighten all screws.
Fitter Plate Screw
Keyhole
Slot
Keyhole
Slot
Fitter
Plate
Light Pan
13
14
15
Motor Screw
Blade Arm
12. Install the blade arm to the underside of the motor
assembly with previously removed motor screws. Tighten
each blade arm completely before moving to the next.
12

ASSEMBLY INSTRUCTIONS
10
Mounting
Screw
Battery Door
Battery Compartment
Front
Keyhole
Slot
Light
Cage
Cage Screw
Back
Wall Bracket
16
17
18
17. Remove the battery door from the back of the remote
using a at-head screwdriver (not included). Insert the two
CR2032 batteries into the remote; ensure the positive pole
of the batteries face up (as pictured) and then replace the
battery door.
Note: Your fan and wall control/remote were synced at the
factory. If the wall control does not operate the fan, see
TROUBLESHOOTING, page 13.
16. Loosen all four and completely remove one of the cage
screws preassembled to the light pan. Then lift the keyhole
slots in the light cage over the loose cage screws and turn
in a clockwise direction. Reinstall the previously removed
cage screw and tighten all screws.
18. If desired, the wall bracket can be installed to the wall
using the two mounting screws. Store the remote in the
wall bracket when not in use.
Turn ON the electrical power at the main fuse or circuit
breaker and the wall switch.
Installation is complete.