Hasler HJ950C User manual

Operating Guide
HASLER
America’s better choice ®
Mailing Systems
And Solutions
HJ950C Addressing System

Hasler would like to Thank You for investing in our quality built
products.
Please record the following information for future reference:
Model:
Serial Number:
Purchase Date:
Purchased From:
Dealer Name:
Contact Name:
Address:
Address:
Phone Number:
Notes
© 2011 Neopost USA Inc. All rights reserved.
No part of this document may be reproduced or distributed in any form or by any means without the express written permission of an
authorized representative of Neopost USA. This document and all information contained herein are confidential and may only be
disclosed as necessary to support customer use of the equipment.
Limitations of this Document
The information presented herein is subject to change. Neopost USA Inc. ASSUMES NO LIABILITY WHATSOEVER FOR ANY
LOSSES OR DAMAGES RESULTING FROM USE OF THIS INFORMATION.

TABLE OF CONTENTS
i
Table of Contents
TABLE OF CONTENTS..............................................................................................................................I
SECTION 1 – GETTING ACQUAINTED ................................................................................................ 1
SAFETY PRECAUTIONS......................................................................................................................... 1
FRONT VIEW ............................................................................................................................................... 2
REAR VIEW ................................................................................................................................................. 3
PRINT ENGINE AREA ................................................................................................................................... 4
BEHIND THE INK TANK DOOR ..................................................................................................................... 5
SECTION 2 – INSTALLING THE PRINTER.......................................................................................... 6
TRANSPORT INSPECTION ............................................................................................................................. 6
TOOLS NEEDED........................................................................................................................................... 6
CHOOSING THE LOCATION .......................................................................................................................... 6
Work-Table Surface Must be Level......................................................................................................... 6
UNPACKING................................................................................................................................................. 7
Accessory Box Contents.......................................................................................................................... 8
INSTALLING MEDIA GUIDES........................................................................................................................ 9
CONNECTING THE PRINTER ....................................................................................................................... 11
Connecting Power ................................................................................................................................11
Connecting to the Computer................................................................................................................. 11
Minimum Computer System Requirements........................................................................................... 11
INSTALLING THE SERVICE STATION .......................................................................................................... 12
INSTALLING THE PRINTER SOFTWARE....................................................................................................... 16
INSTALL THE INK TANKS........................................................................................................................... 19
Ink Tank Anatomy................................................................................................................................. 19
PROCEDURE (Installing the Ink Tanks):............................................................................................ 20
INSTALLING THE PRINTHEAD CARTRIDGE................................................................................................. 22
Printhead Cartridge Protective Packaging.......................................................................................... 22
Procedure (Installing the Printhead):.................................................................................................. 23
SECTION 3 – OPERATING THE PRINTER......................................................................................... 27
CONTROL PANEL FUNCTIONS.................................................................................................................... 27
Printer Status Light Indicators............................................................................................................. 28
SETTING UP THE FEED ............................................................................................................................... 31
PRINTER DRIVER AND TOOLBOX FEATURES.............................................................................................. 34
Printer Driver Properties..................................................................................................................... 34
Using the M Series Toolbox Utility ...................................................................................................... 38
PRINTING................................................................................................................................................... 41
Printhead Cartridge Conditioning ....................................................................................................... 41
General Software Setup Info:............................................................................................................... 41
Setting Up a Job in MS Word® (2003)................................................................................................. 42
Setting Up a Job in Satori Bulk Mailer® ............................................................................................. 45
SECTION 4 – OPERATOR MAINTENANCE....................................................................................... 52
INK TANK STORAGE AND HANDLING ........................................................................................................ 52
REPLACING THE INK TANKS...................................................................................................................... 52
PRINTHEAD CARTRIDGE STORAGE AND HANDLING .................................................................................. 54
CLEANING THE PRINTHEAD CARTRIDGE ................................................................................................... 54
From the M Series Driver: ................................................................................................................... 54

TABLE OF CONTENTS
ii
From the Toolbox:................................................................................................................................54
Using the Clean Printhead Button: ...................................................................................................... 55
Manual Printhead Cleaning:................................................................................................................ 55
Still Experiencing Print Quality Issues?............................................................................................... 55
REPLACING THE PRINTHEAD CARTRIDGE.................................................................................................. 56
CLEARING MEDIA JAMS ............................................................................................................................ 57
INSPECTING/REPLACING THE INK WASTE TRAY........................................................................................ 58
REPLACING THE SHEET SEPARATORS........................................................................................................ 59
SECTION 5 – TROUBLESHOOTING GUIDE...................................................................................... 61
PRINT QUALITY ISSUES:............................................................................................................................ 61
THE PRINTHEAD CARTRIDGE .................................................................................................................... 62
THE PRINTER............................................................................................................................................. 63
ERROR’S AND WARNINGS ......................................................................................................................... 64
Alert Window Messages........................................................................................................................ 64
Toolbox System Status Messages.......................................................................................................... 65
APPENDIX A – HASLER HJ950C SPECIFICATIONS........................................................................ 67
APPENDIX B – SUPPLIES AND OPTIONAL HARDWARE.............................................................. 68
APPENDIX C – PREPARING PRINTER FOR TRANSPORT ............................................................ 70
LOCAL RELOCATION.................................................................................................................................. 70
REMOTE RELOCATION OR SHIPPING........................................................................................................... 70

SECTION 1
GETTING ACQUAINTED
1
Section 1 – Getting Acquainted
SAFETY PRECAUTIONS
THIS EQUIPMENT PRESENTS NO PROBLEM WHEN USED PROPERLY. HOWEVER,
CERTAIN SAFETY RULES SHOULD BE OBSERVED WHEN OPERATING THE HASLER
HJ950C PRINTER.
BEFORE USING THE PRINTER, YOU SHOULD READ THIS MANUAL CAREFULLY
AND FOLLOW THE RECOMMENDED PROCEDURES, SAFETY WARNINGS, AND
INSTRUCTIONS:
9Keep hands, hair, and clothing clear of rollers and other moving parts.
9Avoid touching moving parts or materials while the machine is in use. Before clearing a jam, be sure
machine mechanisms come to a stop.
9Always turn off the machine before making adjustments, cleaning the machine, or performing any
maintenance covered in this manual.
9The power cord, supplied with the machine, should be plugged into a properly grounded wall outlet
located near the machine and easily accessible. Failure to properly ground the machine can result in
severe personal injury and/or fire.
9The power cord and wall plug is the primary means of disconnecting the machine from the power
supply.
9DO NOT use an adapter plug on the line cord or wall outlet.
9DO NOT remove the ground pin from the line cord.
9DO NOT route the power cord over sharp edges or trap between furniture.
9Avoid using wall outlets that are controlled by wall switches or shared with other equipment.
9Make sure there is no strain on the power cord caused by jamming between the equipment, walls or
furniture.
9DO NOT remove covers. Covers enclose hazardous parts that should only be accessed by a qualified
service representative. Report any damage of covers to your service representative.
9This machine requires periodic maintenance. Contact your authorized service representative for
required service schedules.
9To prevent overheating, do not cover the vent openings.
9Use this equipment only for its intended purpose.
In addition, follow any specific occupational safety and health standards for your workplace or area.
This manual is intended solely for the use and information of Hasler, its designated agents, customers, and
their employees. The information in this guide was obtained from several different sources that are deemed
reliable by all industry standards. To the best of our knowledge, that information is accurate in all respects.
However, neither Hasler nor any of its agents or employees shall be responsible for any inaccuracies
contained herein.
MemjetTM is a registered trademark of Memjet Labels, Inc.
All other trademarks are the property of their respective holders.
All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic or mechanical,
including photocopying, recording, or any information storage and retrieval system, without permission in writing from the publisher

SECTION 1
GETTING ACQUAINTED
2
Front View
1. Exit Roller Cover – This cover plate must be removed to install the Service Station.
2. Control Panel – Provides printer controls. See “Control Panel Functions” section.
3. Side Guide Locking Knob – Used to secure the position of the side guide.
4. Rear Media Support Guide – Provides the proper angle to enhance paper feeding and
separation.
5. Media Support Wedge – Allows for adjustments in stack angle, based on media type and
length. Helps to force the media against the separation area. Narrow and wide wedges are
provided with the printer, to accommodate different media widths.
6. Adjustable Media Side Guide – Adjusts to hold the media against the Media Registration Side
Guide.
7. Media Registration Side Guide– All media is registered against this guide. It has two positions.
Inner position for media measuring 3” to 8.5” in width.
Outer position for media measuring 8.6” to 9.5” in width.
8. Sheet Separator Locking Screws – These thumb screws (four total) are used to secure the
positions of the four sheet separators.
9. Top Cover – Provides access to the Print Engine.
10. Ink Tank Door – Hinged door provides access to the Ink Tanks and Ink Waste Tray.
2
10
3
1
4
6789 5

SECTION 1
GETTING ACQUAINTED
3
7
8
1
2
3
456
Rear View
1.
Main Power Switch, Receptacle and Fuse – Plug in AC power cord here. Switch turns main
power on or off. Fuse provides over-current protection. Fuse rating: 2.5A, 250V, slow blow.
CAUTION: Make sure power cord is disconnected from printer before checking/replacing fuse.
WARNING: Press the ON/OFF Button, located on control panel, to properly shut-down the print
engine. Wait until all control panel lights turn off, before you turn off the main power switch.
2. USB Port Connection – (USB 2.0) The USB cable attaches to the printer here.
3. Network Connection – (Ethernet) The network cable plugs in here.
4. Sheet Separators – Used to separate a single piece of media from the stack. There are four sheet
separators on this printer.
5. Feed Rollers – Delivers the bottom piece of media, from the stack, through the separation area
and under the forwarding rollers. There are eight feed rollers on this printer.
6. Media Support Wedge Thumb Screw – Used to secure the Media Support Wedge to the Rear
Media Support Guide.
7. Counter – LCD displays number of pieces run for a given job. Reset button zeros counter.
8. Rear Media Support Guide Knob – Attaches the Rear Media Support Guide to the body of the
printer.

SECTION 1
GETTING ACQUAINTED
4
1
5
2
3
46
7
Print Engine with printhead cartridge
installed and printhead latch closed.
Print Engine Area
1. Antistatic Brush Assembly – This assembly contains an antistatic brush that is used to help
reduce static energy and remove paper dust from the media. This assembly also contains upper
pressure rollers and fingers that help guide the paper into the print engine.
2.
Printhead Latch – When lowered and locked this device connects the Ink Couplings with the
Printhead Cartridge. Note: The printhead latch on your printer may be blue or black.
WARNING! Never attempt to open the printhead latch manually, when in the closed/locked
position. Sever damage will result. Use the Printhead Release function from the Toolbox utility on
your PC or press the Printhead Latch Release button if a computer is not available.
3. Clean Printhead Button – The button located below this opening can be used to enable a “Level 1
Cleaning” cycle. Insert a non-conductive tool (i.e. plastic pen) into the opening provided, and
lightly press the button.
Additional levels of cleaning can be enabled from the M Series Driver services.
4. Ink Couplings – These devices connect the ink tubes to the printhead cartridge. The printhead
latch is used to engage or disengage these devices from the printhead cartridge.
5. Printhead Latch Release Button – The button, located below this opening, can be used to initiate
the printhead latch release cycle. Insert a non-conductive tool (i.e. plastic pen) and lightly press the
button. If the system is primed it will run a deprime cycle before releasing the latch. This feature
can also be initiated from the Toolbox utility and M Series Driver services.
6.
Print Engine Latches – Lift up on both latches, at the same time, to release and swing open the
top section of the Print Engine.
CAUTION! Do NOT open the Print Engine while the printer is operating.
Make sure the Print Engine is closed and locked before operating.
Do NOT open the Print Engine to an angle greater than 60º.
7. Printhead Cartridge – Memjet® printhead; produces an 8.5” wide, full color, print area.

SECTION 1
GETTING ACQUAINTED
5
Behind the Ink Tank Door
2
1
3
1. Ink Tank Securing Latches – Used to hold the Ink Tanks in the slots.
NOTE: Please be sure that both sides, at the bottom part of the latch, are engaged.
2. Ink Tanks – Five Ink Tanks are used in the printer.
Cyan (C), Yellow (Y), Magenta (M), Black (K), Black (K)
3. Ink Waste Tray –The purpose of this tray is to catch any waste ink produced by the system. This
tray is filled with absorbent material.
The tabs located at the left and right sides of the tray; secure the tray to the print engine frame.
Please be sure the tabs “click” into the frame to secure the tray’s position.

SECTION 2
INSTALLING THE PRINTER
6
Section 2 – Installing the Printer
Before using the Hasler HJ950C printer the following must be done:
•Upon delivery; inspect packaging and report any issues to Carrier.
•Choose a location for the printer
•Unpack and assemble the printer
•Install the Service Station (to be done by a qualified technician)
•Install the Printer Software (Drivers and Toolbox)
•Install the Ink Tanks
•Install the Printhead
•Set up the feed on the printer to accommodate your media (covered in Operating the Printer).
Transport Inspection
The printer is shipped in appropriate packaging so that, under normal shipping conditions, it reaches its
destination without damage.
NOTICE: Report damage to the carrier. The carrier is liable for any damage during transport.
Transport and storage should take place under the following conditions:
- At temperatures between -25°C and +50°C (-13 °F to 122 °F).
- At a relative air humidity between 5% and 95%, non-condensing.
- At an atmospheric pressure between 70 kPa and 105 kPa.
Exposure to conditions that are not permissible may lead to damage which is not externally visible.
IMPORTANT Please save the packaging materials for future use! It will be required if you ever need to
ship the printer. Before shipping; please refer to the appendix section “Preparing the Printer for Transport”.
Tools Needed
•Knife and scissors to open packaging
•#2 Philips head Screwdriver
•Carpenters Level (recommend using 18” or longer level)
•Protective gloves should be worn to avoid getting ink on hands when removing protective
packaging materials from the ink coupling areas, the Ink Tank areas, and when
installing/removing Printhead Cartridge and Ink Tanks.
Choosing the Location
The Hasler HJ950C should be placed on a sturdy, level, worktable or cabinet at least 9 inches from any
walls. Protect the HJ950C from excessive heat, dust, and moisture – avoid placing it in direct sunlight.
Work-Table Surface Must be Level
The surface that the printer is placed upon must be level, front to back and side to side. Use a
carpenter’s level to verify that the surface is level. If the surface is not level the printer will not perform
properly. Do NOT move the printer while the power is on.
Operation should take place under the following conditions:
- At temperatures between +15°C and +35°C (-59 °F to 95 °F).
- At a relative air humidity between 20% and 80%, non-condensing.
- At an atmospheric pressure between 70 kPa and 105 kPa.
Exposure to conditions that are not permissible may lead to damage which is not externally visible.
Allow the printer, printhead and ink tanks to acclimate to ambient temperature before using the printer.

SECTION 2
INSTALLING THE PRINTER
7
Unpacking
Please refer to the unpacking sequence, shown below.
NOTE: Packaging materials may vary slightly from what is shown below.
Please save the packaging in a safe place, for possible future use.
Two people will be required to safely lift the printer and place it onto a sturdy, level work table.
IMPORTANT: WORK TABLE SURFACE MUST BE LEVEL!LEVEL!
Save the Packaging for possible future use.
1 2
3 4
5 6

SECTION 2
INSTALLING THE PRINTER
8
AB C
DE
F
GH
IJ KK
Accessory Box ContentsAccessory Box Contents
The following items are included with your printer:The following items are included with your printer:
QtyQty [Image Reference] Description
5 [A] Ink Tanks
- Cyan, Magenta, Yellow, Black, Black
1 [B] Printhead Cartridge and packaging
1 [C] Rear Media Support Guide
- thumb screw attached to printer
1 [D] Service Station
1 [E] Wide Media Support Wedge
- mounting hardware attached to item C
1 [F] Narrow Media Support Wedge
- mounting hardware attached to item C
1 [G] Media Registration Side Guide
- mounting screws attached to printer
1 [H] Adjustable Media Side Guide
- mounting screws attached to printer
1 [I] USB Cable
1 [J] Power Cord
1 [K] HJ950C Operation CD
- contains printer software and pdf manual
Note: Ink Tanks and Printhead Cartridges can be purchased through your local Hasler dealer. To
locate a Hasler dealer in your area, please use the following link. www.haslerinc.com.
See “Appendix B” for supplies selection.
Items contained in the Accessories Box

SECTION 2
INSTALLING THE PRINTER
9
Installing Media Guides
The screws needed to attach the side guides to the printer are located under the shipping tape in their
respective positions.
1. Begin by installing the Media Registration Side
Guide using the two screws [1] provided:
2. Next install the Adjustable Media Side Guide
using the two screws [2] provided.

SECTION 2
INSTALLING THE PRINTER
10
3
5
6
78 9
3. Attach the Rear Media Support Guide using the
knob [3] provided.
The two outer holes in the guide fit over the
socket head screws; as shown.
4. Install the desired Media Support Wedge using the
mounting hardware [4]; as described below.
Choose the appropriate Media Support Wedge for your
application:
Wide Media Support Wedge [5]
– For media that is 8 inches wide or greater.
Narrow Media Support Wedge [6]
– For media that is less than 8 inches wide.
The Anchor Plate [7] fits into the slot, from the underside
of the Rear Media Support Guide. Position the Media
Support Wedge so the upper and lower holes fit onto the
two tabs from the Anchor Plate.
The washer [8] goes between the Thumb Screw [9] and
the Media Support Wedge. The Thumb Screw is inserted
down through the washer, then through the center hole in
the Media Support Wedge and into the threaded hole in
the Anchor Plate. Tighten the thumb screw to secure the
Media Support Wedge onto the Rear Media Support
Guide.

SECTION 2
INSTALLING THE PRINTER
11
Connecting the Printer
Connecting Power
Check to make sure that he Main Power Switch [1] is in the OFF position.
Connect the AC power cord to the printer’s receptacle [1].
Connect the other end of the AC power cord to a 115 – 230 volt AC, 50/60 Hz,
grounded outlet.
Do NOT turn the printer on at this time.
NOTE: The use of a surge protector/line conditioner is highly recommended.
CAUTION
DO NOT USE AN ADAPTER PLUG OR EXTENSION
CORD TO CONNECT THE PRINTER TO THE WALL
RECEPTACLE.
DO NOT USE OUTLETS CONTROLLED BY WALL
SWITCHES.
DO NOT USE AN OUTLET THAT SHARES THE
SAME CIRCUIT WITH LARGE ELECTRICAL
MACHINES OR APPLIANCES.
Connecting to the Computer
The Printer connects to the computer through the USB port (2).
A Network (Ethernet) port (3) is provided for operation in a network environment.
NOTE: At the time of this manuals publication, information on connecting the printer via the Network
(Ethernet) port was not available. Please contact your support representative for network connection help.
IMPORTANT: Do NOT connect the printer to the computer, until prompted to do so, during the printer
driver installation process. See “Installing the Printer Software” section.
Minimum Computer System Requirements
•Windows XP, Windows Vista, Windows 7. Supports 32 and 64 bit systems.
You must have administrative privileges on the system.
•Pentium II, 2 GHz minimum (Pentium Dual Core, 2.5 GHz or better, is optimal)
•System memory – 2 GB minimum; or as recommended for your operating system.
•At least 10 GB free hard-disk space.
•Microsoft Internet Explorer 6.0 or higher.
•Java version 6 or higher
•CD/DVD drive
•USB 2.0 port

SECTION 2
INSTALLING THE PRINTER
12
Installing the Service Station
Due to the technical nature of this procedure; this process should only be performed by a qualified technical
support person. This process is normally performed when the printer is first installed or when technical
maintenance is needed on the printer.
CAUTION
THIS PROCESS MUST BE PERFORMED BY A
QUALIFIED TECHNICAL SUPPORT PERSON.
The Service Station fits in the slot immediately above the Ink Tank slots.
The Service Station contains three separate areas/devices that are used to perform the following tasks.
•Cleaning. The wiper roller cleans the Printhead nozzles of excess ink and debris.
•Printing/Purging. This area acts as a base to support media during printing. It also contains a
purging area; which captures and absorbs ink that is purged, to help keep nozzles clear.
•Capping. This area seals and protects the printhead nozzles when not in use.
PROCEDURE:
1. Make sure the printer is powered OFF.
If the printer is not powered off, press the ON/OFF button once and wait about 45 seconds for the
print engine to power off (all control panel light’s off). Then turn the Main Power Switch OFF.
2. Open the Ink Tank Door (hinged at bottom).
3. Open the Top Cover.
4. Remove the Exit Roller Cover by removing the four (4) screws.
The Service Station Slot and Ribbon Cable will be exposed.
Ribbon
Cable
Service Station
Slot
Ink Tank
Door

SECTION 2
INSTALLING THE PRINTER
13
5. Carefully remove the Service Station from its packaging.
NOTE: Loose parts may fall out. Keep wiper roller side facing up, when removing the packaging.
6. Slide the Cable Securing Latch open on the Service Station Circuit Board; as shown below.
7. Insert the Ribbon Cable (blue side up) into the space under the Cable Securing Latch [1].
Make sure the ribbon cable is pushed in all the way and is NOT crooked. Then close the Cable
Securing Latch [2].
CAUTION!
Make sure latches on the Wiper Roller are fully latched before installing the Service Station.
Closed Opened
Open Close
1 2
Check the latch at each end of
the wiper roller.

SECTION 2
INSTALLING THE PRINTER
14
Wiper Roller end of
Service Station
Ribbon Cable
Connected to Service
Station Circuit Board
8. Once the Ribbon Cable is properly connected to the Service Station Circuit Board; gently slide the
Service Station, wiper roller end first, into the Service Station Slot until it stops. The Service
Station fits into the slot immediately above the Ink Tank slots.
NOTE: The Ink Tank Door must be open to perform this procedure.
9. Look down through open area of the Printhead
Cartridge compartment, in the top of the Print
Engine, to make sure the Service Station is aligned
with the “Bar”; as shown.
IMPORTANT! Service Station must perfectly
aligned with “Bar” to prevent misalignment and
jamming of the service station.

SECTION 2
INSTALLING THE PRINTER
15
You don’t need to open the Print Engine.
Shown for clarification purpose only.
10. GENTLY push in on the Service Station with one hand, while slowly turning the “Large Gear”
clockwise with the other hand. It should be easy to turn this gear and the service station should
start to drive into the print engine squarely.
Once the Service Station moves about ¼ inch past the “Bar” (shown in previous step), stop turning
the gear. Do NOT manually drive the Service Station into the print engine beyond this point.
NOTE: The “Large Gear” is located on the non-operator side of Print Engine; as shown below.
You don’t need to open the Print Engine to access this gear.
11. Turn the printer’s Main Power Switch ON; then press the control panel’s ON/OFF button.
After printer initialization (~45 seconds) the Print Engine will automatically pull the Service
Station the rest of the way in.
NOTICE: If the Service Station should get jammed during this process (you hear motor stall noise
or gear slipping noise); immediately turn OFF the printer’s Main Power Switch. This is one of the
only exceptions for turning off the printer using the main power switch, before properly powering-
down the print engine. Remove the Service station by turning the Large Gear counter-clockwise.
Re-check that the Wiper Roller is properly installed and latched at each end. Then re-install the
Service Station starting from step 8 above.
Tip: The “Eject Service Station” button, located in the M Series Toolbox, should be used if the
service station needs to be removed in the future.
12. Re-install the Exit Roller Cover plate, using the 4 screws. Make sure the cover is installed in the
proper orientation.
Tip: Since the Exit Roller Cover is also an integral part of the frame structure; you may need to
push in on the outer frames to get the screw holes in the Exit Roller Cover to align.
Close the Top Cover and the Ink Tank Door.
Ink Tank
Door

SECTION 2
INSTALLING THE PRINTER
16
Installing the Printer Software
During this process the M Series Driver and M Series Toolbox utility will be installed onto your computer
system.
NOTE: If you are updating the HJ950C (M Series) printer software (printer driver and toolbox utility);
please be sure to Uninstall the old software before installing the new software. Use the “Uninstall”
feature found on your computer system under All Programs, “Memjet”, “M Series Driver”.
PROCEDURE
1. Disconnect the USB cable connection from the printer; if you plugged it in already.
2. Insert the CD, supplied with the printer, into your CD drive. If the “Launch Menu” window does
not automatically open in your browser. Locate and run the “MENU_LAUNCH.htm” file, located
on the root directory of the CD.
3. When the HJ950C Operation CD “Launch
Menu” window opens on the computer screen;
Click “Install Printer Software”.
NOTE: If you receive a Windows security or
authorization warning, click on “YES” or
“Continue Anyway”.
Tip: If you are unable to start the software
installation using the button in the “Launch
Menu”: Browse to the CD. Locate and open the
Printer Drivers folder. Located and run
“Install.exe” to start the install.
4. When the License Agreement window opens.
Carefully read the “End User Agreement”.
If you agree to the terms, check “I accept…”
then click Next>.