Havis C-VS-2000-DUR-1 User manual

C-VS-2000-DUR-1_INST_8-17
INSTALLATION INSTRUCTIONS
C
-
VS
-
2000
-
DUR
-
1
20” VEHICLE SPECIFIC CONSOLE for
2018-2020 Dodge Durango with Standard Shifter
TOOLS REQUIRED:
Phillips Screw Driver T-20 Torx bit Standard Socket set 9/64”Allen wrench
Metric Socket set Wire crimping tool Wire cutters Trim removal tool
Always!
 Read all instructions before installing any Havis, Inc. products.
 Check for obstructions (Wires, brake lines, fuel tank, etc.) before drilling any holes!
 Use hardware provided with install kit
INSTALLATION PARTS AND MOUNTING HARDWARE:
QTY DESCRIPTION PART#
1 Main Console housing
1 Top console Bezel CM008968
1 Main floor mount bracket CM010022
1 Gear shift stand CM008969
1 Shifter mount bracket CM008994
1 Driver side trim panel CM008995
1 Passenger side trim panel CM008996
2 Retaining bracket CM005270
1 Gear shift boot spacer CM008970
1 Gear shift boot plate CM008971
1 2” x 2 ½” x 8” foam block CM007533
8 # 8 x 3/8” Torx head screw CM86508
2 12 volt socket CM216560
2 10-32 Nylock nut GSM30015
6 10-32 Keps nut GSM30028
12 1/4 serrated nut GSM30023
20 1/4 Flat washer GSM31005
6 1/4 Lock washer GSM31026
4 1/4 x 1/2” Carriage bolt GSM31999
6 1/4 x 1/2” Hex head bolt GSM33000
10 1/4 x 3/4” Hex head bolt GSM33001
4 1/4" x 1” Hex head bolt GSM33002
2 10-32 x 1/2” Phillips pan head machine screw GSM33118
4 8-32 x 3/8” Phillips pan head machine screw GSM33137
4 # 8 x 1/4” Flat head sheet metal screw GSM33178

C-VS-2000-DUR-1_INST_8-17
C-VS-2000-DUR-1
(Main Housing Assembly)
CM008996
Passenger side trim panel
CM008995
Driver side trim panel
CM005005
Floor mount bracket
CM005270
Retaining brackets
CM008968
Top console bezel
CM008970, CM008971
Gear shift boot spacer,
Gear shift boot plate
CM008969
Gear shift stand
(Inside console not shown)

C-VS-2000-DUR-1_INST_8-17
View of OEM console prior to
removal.
Carefully pop out coin tray from console
top panel. (coin tray to be reused)
Note: Some vehicles may have a coin
tray/traction control switch.
Unplug and remove shifter and set
aside.
(OEM bolts will not be reused)
Carefully pop up shifter boot and
unplug sensor from rear of boot.
Loosen Allen head bolt and remove
shifter handle from stalk.
(9/64” Allen wrench)
Unbolt shifter assembly from center
console using 8mm socket and
ratchet.
Carefully unclip and remove top
console panel.
Unplug all wire connectors.
Carefully unclip and remove rear
console end panel. Unplug wires as
needed. Some vehicle may not have
wiring.
Carefully unclip and remove
console forward side panels.

C-VS-2000-DUR-1_INST_8-17
Remove bolts at lower front of
console and the screws at forward
lower dash. (save hardware)
(10 mm and 7 mm sockets)
Remove screws for the rear side trim
panels, Arm rest hinge and the Manual
Park Release pull strap.
(Phillips screwdriver)
Note: See owner’s manual section
“What to do in Emergencies”
for more Park Release information.
Remove storage pocket in order to
access and remove Manual Park
Release pull strap assembly from
OEM mount.
Remove bolt cover at lower rear
end of console. (one each side).
Remove bolts and save.
(10 mm socket)
Remove screws for the rear side
trim panels.
(Phillips screwdriver)
Carefully Unplug and Unclip wire
harness from OEM console base so
the base can be removed.
Remove screws for the storage
pocket.
(Phillips screwdriver)
Flip console base upside down and
remove air duct. Remove Manual
Park Release cable from bottom of
OEM plastic console base.
Note: DO NOT disconnect or remove
cable assembly from vehicle.
Remove remaining wire harness
from OEM console base and
reconnect to main harness.
View with OEM center console
removed.

C-VS-2000-DUR-1_INST_8-17
Insert 2” x 2.5” x 8” foam block into
lower dash air duct to prevent air
from blowing into console.
Foam part number - CM007533
Loosely attach the forward floor “U”
bracket to the rear base bracket with
1/4 x 3/4” Hex head bolts, lock
washers and flat washers.
Loosely attach console housing to
front floor mount bracket with
1/4” x 3/4" hex head bolts, lock
washers and flat washers.
(two each side)
Bolt the main floor bracket to OEM
mount locations with the previously
removed OEM bolts.
(10 mm socket)
Attach gear shift stand to shifter
mount bracket using four (4) 1/4" x
1/2" hex head bolts, flat washers
and serrated nuts.
Place main console housing onto
floor bracket.
Attach the OEM shifter to the gear
shift stand using 1/4" x 1” hex head
bolts, washers and serrated nuts.
Loosely attach console housing to
rear floor mount bracket with
1/4” x 1/2" carriage bolts and
serrated nuts.
(two each side)
Attach front side console housing to
forward lower dash with previously
removed O.E.M. screws.
(7mm socket)
Tighten all console mount hardware.

C-VS-2000-DUR-1_INST_8-17
Attach passenger side trim panel to
console housing with # 8 x 1/4" flat
head sheet metal screws.
This photo also shows the alternate
location for the 12 volt socket.
Remove forward Aux input module.
(T-20 Torx)
Add the gear shift boot plate onto
the gear shift boot spacer following
the orientation shown in the photo.
Tighten with 10-32 Keps nuts.
Attach driver side trim panel to
console housing with # 8 x 1/4" flat
head sheet metal screws.
View of OEM top console assembly
previously removed.
Place the gear shift boot spacer
onto the top console bezel
following the orientation shown in
the picture
.
Place Aux input module onto studs
and attach with four (4) 8-32 x 3/8”
machine screws.
Place coin tray on the
underside
of top
console bezel. Clamp on with brackets
and 10/32 Nylock nuts as shown.
(3/16” socket)
New console faceplate ready to be
installed.
Note: Some vehicles will have the
coin tray/traction control knob
that mounts the same way.

C-VS-2000-DUR-1_INST_8-17
Reattach O.E.M. harnesses and
plugs.
OR
Manual park release can be mounted to
back of console using 10-32 x 1/2"
machine screws and Keps nuts.
Note: In this location, the release
assembly could possibly get damaged
when seat is slide reward.
If mounting a C
-
HDM
-
204 or 214 side
computer mount, use the existing 1/4"
hex nuts with 1/2" hex bolts and flat
washers in upper side extrusion.
Use 1/4” x 3/4" hex head bolts and flat
washers for bottom mounting.
Carefully place top faceplate onto
console and attach with # 8 x 3/8”
Torx head screws. Slide shifter back
on and plug in shifter boot to OEM
harness
Tighten Allen head bolt to OEM
shifter stalk. (9/64” Allen wrench)
Snap shifter boot down into shifter
boot plate
Run wiring as needed. Mount face
plates and accessories into console
with # 8 x 3/8” Torx head screws.
Screws supplied with equipment
brackets and accessories.
Manual
park release
needs to
be looped
inside console and located so access can
be done by removing cup holder.
Note: See owner’s manual section
“What to do in Emergencies”
for more Park Release information.
Install computer mount assembly
and make final adjustments.
Installation is now complete