Havis C-DMM-3006 User manual

C‐DMM‐3006_INST_9‐18


INSTALLATION INSTRUCTIONS
C‐DMM‐3006FlipupDashMonitorMount
2017‐2020F‐250,350,450Pickup,F‐450and550CabChassis,
2015‐2020FordF‐150Retail,Responder&SSV,
2018‐2020ExpeditionRetail&SSV
**DoesNOTworkwithOEMtopcenterdashspeaker.
OEMtopTrayandspeakerassemblymustberemovedandnotused.**
TOOLSREQUIRED:
RatchetWrench Dashpanelremovaltool OpenEndWrench‐7/16”
SocketSet   Philli
p
sscrewdriver Plasticcuttin
g
tool
(
o
p
tional
)
Always!
ReadallinstructionsbeforeinstallinganyHavis,Inc.products.
Usehardwareprovidedwithinstallkit
HARDWAREandPARTS:
QTY DESCRIPTIONPART#
1MainF‐SeriesframebracketCM009455
1ForwardsupportbracketCM009514
1Maintrayreplacementbracket  CM009510
1SidemountingbracketCM009454
11.0625”DomeplugGSM20017‐1
11/4"SerratednutGSM30023
2M6HexnutGSM30201
11/4"x3/4"BoltGSM33001
2#10Phillipspanheadsheetmetalscrew GSM33196
310‐32x1/2"MachinescrewGSM33118
5#10FlatwasherGSM31003
1VESArotatorplateCM009068
1PVCwasherCM008582
21/4"PlasticwasherCM86600
31/4"SteelwasherGSM31005
21/4"NylocknutGSM30016
Notes:
TheC‐DMM‐3000swivelplateacceptsC‐MM‐301offsetbracketusedwithC‐MM‐2XXadaptors.
C‐MM‐2XXseriesadaptorbracketsarenotneededformostVESA75andotherHavisDockingStation
mountingapplications.
CM009068VESArotatorplategivesadditionalpositioningoptions,butisnotrequireddependingon
mountingpreference.

C‐DMM‐3006_INST_9‐18


C‐DMM‐3006
Assembly
CM009510
Maintray
replacementbracket
GSM33118
10‐32x1/2"screw
GSM31003
#10Flatwasher
GSM20017‐1
1.0625”Domeplug
GSM33118
10‐32x1/2"screw
GSM31003
#10Flatwasher
GSM33196
#10Sheetmetalscrew
GSM31003
#10Flatwasher
CM009514
Forwardsupport
bracket
GSM30201
M6Hexnut
CM009454
Sidemounting
bracket
GSM33001
1/4"x3/4bolt
GSM31005
1/4"Flatwasher
GSM30023
1/4"Serratednut
CM009068
VESArotator
plateCM008582
PVCwasher
GSM31005
–
Flatwasher
CM86600–Nylonflatwasher
GSM30016–Nylocknut

C‐DMM‐3006_INST_9‐18


Viewofthedashbeforeinstallation
Loosen(2)OEMfastenersontherightofthe
displayandattachsidemountingbracket.
CarefullyremovecenterHVACandradio
controltrimbezel.
Removetwo(2)fastenersfromupperdisplayarea.
(7mmsocket)
LiftupandremoveOEMplastictray.
Thistraywillnotbereused.
Removetwo(2)fastenersfromtheforwardsectionofthetray.
(7mmsocket)
Note:Ifequippedwithcenterchannelspeaker,simplypopup
grilltoaccessscrews.Speakerwillnotbereused.

C‐DMM‐3006_INST_9‐18




Thesidetriminnerflangecanbenotched if
desiredforabetterfit.
Markandnotchareaforbracketclearance.
Install(2)M6hexnutsoverfactorystudsandtighten.
Placemaintrayreplacementbracketinopeningandline
uptofactorystudsindash.
Runwiresthroughholeorcoverholewithsuppliedplug.
Re‐installsidemountingbracket.
Re‐installcenterHVACandradiocontroltrim.
Tightenhardware.Ifyoudesiretorunwiringup
throughdash,itshouldbedonepriortonextsteps.
Usingpreviouslyremoved7mmheadhardware.Attach
forwardmountingbrackettofactoryspeedclips.

C‐DMM‐3006_INST_9‐18



Attachforwardendoftraywith10‐32x1/2"
machinescrewand#10flatwasher.
Runwireharnessandtestcomputer.
Installationisnowcomplete.
Doublecheckandtightenallhardware.
Makesurelatchingisworkingproperly.
Placemainhingeframeontopandlooselyattachtotraywith
10‐32x1/2"machinescrewsandflatwashers.AttachtoOEM
speednutswith#10sheetmetalscrewsandflatwashers.
AttachVESAswivelplatetothebackofDockorDockbracket.
Determinedesiredpositionforyourspecificcomputerandattach
toDMMswivelplateusingnylonwashers,steelwashers,and
nylocknuts.Tightensodockissnug,butrotatessmoothly.
Lineupthelowerframetothesidesupportbracket
andattachwith1/4"bolt,flatwasherandserratednut.