Havis C-VS-1500-TAH-1 Configuration guide


  C‐VS‐1500‐TAH‐1_INST_11‐18



INSTALL INSTRUCTIONS C-VS-1500-TAH-1
2015-2018 Chevy Tahoe Police Pursuit Vehicle (PPV)
Vehicle Specific Console (9” inches wide) 15” inches of Equipment mounting space
Note: 2” inches of mounting space is for the supplied Aux panel.
Console only includes an additional 13” inches of customer specified equipment brackets
and filler panels.
Tools Required:
Phillips Screw Driver Standard Socket set T-20 Torx Bit
Metric Socket set Wire Cutters Wire Crimping tool
Parts and Mounting Hardware:
1 – Main console housing CM007917
CM007918 Sub Assembly
2 – Floor bracket CM006193
2 – 1/2” Aluminum spacer for floor bracket (rear) CM003200
2 – 3/4” Aluminum spacer for floor bracket (front) CM003216
1 – Driver side trim panel CM008222
1 – Passenger side trim panel CM009197
1 – Electrical accessory mounting plate CM006415
1 – Rear mounting plate CM006831
1 – 2” inch panel for OEM 12 volt socket and Aux module C-EB20-USD1-1P
2 – 7/8” hole plug (included with C-EB20-USD1-1P)  CM86430
1 – 2” Dome plug for rear mounting plate GSM20068
16 - #8 x 3/8 Torx head sheet metal screws CM86508
8 - 1/4” serrated nut GSM30023
2 - 1/4” Flat washer GSM31005
8 – 1/4” x 3/4” Carriage bolt GSM32000
10 - 1/4” x 3/4” Hex bolt GSM33001
4 – 3/8” Flat washer GSM31149
4 – 10mm x 45mm Hex bolts (if floor is already threaded) GSM33733
4 – 3/8 x 1.75” Hex bolt (if floor mount location is not threaded) GSM33303

ALWAYS!
• Read all instructions before installing any Havis, Inc products.
• Use hardware provided with install kit






  C‐VS‐1500‐TAH‐1_INST_11‐18


CM009197
Passenger side trim panel
CM006193
Floor bracket
(one each side)
Electrical Accessory
mounting plate
Between trim panels
CM006415 2” inch panel # C-EB20-USD1-1P
For OEM 12 volt socket and Aux module.
Also has two (2) 7/8” holes for optional
12 volts sockets. Order 12 volts socket kit
C-HK-181 separately (if desired)
IMPORTANT NOTE:
Install CM006193 floor brackets to existing OEM mount points as follows.
Between bracket and hump, use 1/2” spacers at rear and 3/4” spacers at front.
RE: Police Pursuit Vehicle without center seat or OEM console
Use 3/8” x 1.75” self threading bolts and 3/8” flat washers and spacers
RE: Retail Tahoe or PPV (code A95) with OEM center console or PPV with center seat
Remove console or seat and use 10mm x 45mm bolts and 3/8” flat washers and spacers
Photos currently do not show the new speaker vents in the side trim panels. It is up to the installer to determine if a
speaker or other device can be mounted behind these vents for their specific application.
CM006831
Rearmountingplate
Main Console Housing
CM008222
Driver side trim panel
C-VS-1500-TAH-1
(Assembly)


  C‐VS‐1500‐TAH‐1_INST_11‐18




View of 2015 Tahoe transmission hump
between front seats
Install CM006193 floor brackets to existing OEM mount points. Use
10mm x 45mm bolts and 3/8” flat washers if the vehicle had a factory
center console or seat installed. Use 3/8” x 1.75” self-threading bolts and
washers if vehicle does not have the center seat or console. Between
b
racket and hum
p,
use 1/2” s
p
acers at rear and 3/4” s
p
acers at front.
Place console on the floor brackets and line up
to dash and the slots in the track. Using the opening in the bottom of the console
attach the 1/4" serrated nuts (GSM30023) to the
bolts
Place the Rear Mounting Plate (CM006831)
behind the console and line up with the tabs.
Using the 2” hole slip in the 1/4” serrated nuts
and attach to the bolts.
Looselyattachtheelectricalaccessorymountingplate
(CM005915)totheconsole“U”bracketwith1/4”x3/4"
Hexboltsand washers.
(
f
orwardmounttabsfacedown
)


  C‐VS‐1500‐TAH‐1_INST_11‐18



Attach driver side trim panel to console with
four (4) #8 x 3/8 Torx head sheet metal screws.
Attachpassengersidetrimpanelthesame
wayasdriverside.
Note: This photo shows the OEM 120 volt socket mounted in the side
trim after metal knockout plate has been removed. OEM wire ties and
tape may need to be cut in order to have enough wire to extend to this
location. Splicing four (4) wire extensions may also be required.
Wire and eight (8) butt connectors for extensions must be supplied
by the installer.
Once both side trim panels are attached check
for final fitment and tighten all hardware
Console housing installation complete
Install 2” inch panel C-EB20-USD1-1P for OEM 12 volt
socket and Aux module (if desired)
Console shown with C-CUP-I-A11 cup holder
and equipment bracket Console mounted with optional C-ARM-104


  C‐VS‐1500‐TAH‐1_INST_11‐18


Optional C-1000 enclosed console provides an
additional 10” of mounting space. Installation complete
View of C-HDM-204 mounted to the console
housing with C-MD-302, PKG-KB- 106, and
DS-GTC-201.
View of C-HDM-204 mounted to the outside of
console housing with C-MD-302, PKG-KB-
106, and DS-GTC-201.
DMM 130 installed with CM006331 and PKG-
KB-106. Also works with C-DMM-135. Double check all mounting and equipment
functions.