Havis DS-GTC-210 Series User manual

Owner’s Manual
Havis Docking Station
For Getac F110 Rugged Tablet
DS-GTC-210-SERIES_OMN_11-17
www.havis.com
1-800-524-9900
DS-GTC-211
DS-GTC-211-3
DS-GTC-212
DS-GTC-212-3
DS-GTC-213
DS-GTC-213-3
DS-GTC-210 Series
Havis, Inc.
75 Jacksonville Road
Warminster, PA 18974
www.havis.com 1-800-524-9900
DS-DA-311
USB Extension Cable
Allows for more convienent access for up to two (2) of the
available USB 2.0 ports. Can be mounted to the right, left,
or both sides on DS-GTC-200 Series Docking Stations.
Related Products
Havis offers a wide variety of accessory products specically for use
with the DS-GTC-210 Series Docking Station. For more information or
to order, please visit www.havis.com.
LPS-116
95W Power Supply
External in-vehicle power supply and cable for Getac
F110 Rugged Tablet with cigarette lighter adaptor.
DS-DA-218
Desktop Stand for Tablet Docking Stations
Durable stand for mounting tablet Docking Stations
for use in the home or office.
DS-DA-102
Night Eyes II
In-vehicle night time viewing from six long lasting,
soft true, red LED lights on a exible steel gooseneck.
DS-DA-501
Replacement Keys
Set of two (2) replacement keys for DS-GTC-210
Series Docking Stations.

www.havis.com • 1-800-524-9900
DS-GTC-211
DS-GTC-211-3
DS-GTC-212
DS-GTC-212-3
DS-GTC-213
DS-GTC-213-3
Before Beginning (Original Instructions)
2 11
• NEVER STOW OR MOUNT THE DOCKING STATION DIRECTLY IN A VEHICLE
AIRBAG DEPLOYMENT ZONE.
• DO NOT USE COMPUTER WHILE DRIVING.
Havis is pleased to provide this Owner’s Manual to aid in the proper
installation and use of the DS-GTC-210 Series Docking Station for
the Getac F110 Rugged Tablet.
For questions regarding the set-up of your DS-GTC-210 Series Docking Station,
please contact Havis at 1-800-524-9900 or visit www.havis.com for additional
product support and information.
This Owner’s Manual applies to the following Part Numbers:
• FOR DOCKING STATION MODELS EQUIPPED WITH A BUNDLED POWER SUPPLY
(DS-GTC-212, DS-GTC-212-3) REFER TO THE SUPPLIED LIND POWER SUPPLY REFERENCE GUIDE.
• WHEN TABLET IS DOCKED, THE BATTERY WILL ONLY CHARGE BETWEEN
0°C to 50°C (32°F to 122°F).
PLEASE REFER TO GETAC F110 OWNER’S MANUAL FOR MORE INFORMATION.
Optional Accessories
DS-DA-311 - Remote USB Extension Cable
(For further Installation Instructions, refer to the Instructions included with DS-DA-311)
1) Determine if USB will exit the left or right side of Docking Station.
2) Remove the Screws from USB Cable.
3) Align the female end of the USB Cable with mounting surface hole pattern.
Insert Screws and Lock Washers and tighten Screws.
CAUTION: DO NOT OVERTIGHTEN SCREWS
4) Plug male end of USB Cable into USB Port.
5) Strain Relief cable as needed.
6) If the connected peripheral has a cable requiring strain relief, use
Int. Zip Tie (Hardware Kit Item #1) by snapping into hole just below port.
7) Continue on with Installation on Page 6.
ScrewsLock WashersUSB 2.0 Panel Mount Extension Cable Mounting SurfaceUSB Port
Male End Female End/
Panel Mount
• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.
• DO NOT STORE, INSTALL, OR OPERATE THE DOCKING STATION WHERE WATER, MOISTURE,
STEAM, DUST, ETC. ARE PRESENT
• DOCKING OR UNDOCKING YOUR COMPUTER WHILE IN ON, STANDBY, HIBERNATION, OR
SLEEP MODE CAN CAUSE SOME DEVICES TO NOT INITIALIZE PROPERLY. IF THIS OCCURS,
PLEASE TURN OFF YOUR COMPUTER AND RESTART IT WHILE IT IS DOCKED.
• FOR THE DS-GTC-211, DS-GTC-211-3, DS-GTC-212 & DS-GTC-212-3 DOCKING STATIONS:
DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: This product requires
a certied, automotive grade, Getac approved 95W power source rated for a
continuous, regulated 19VDC output (Havis Part Number LPS-116 or equivalent).
Failure to comply with this requirement will cause product damage that is NOT
repairable and is NOT covered under warranty.
• FOR THE DS-GTC-213 & DS-GTC-213-3 DOCKING STATION:
DO NOT CONNECT DIRECTLY TO VEHICLE VOLTAGE SOURCE: The Getac F110 tablet
requires a certied, Getac approved power source rated for a continuous, regulated
19VDC output. Getac recommends using the power adapter included with the tablet;
failure to comply with this requirement will cause product damage that is NOT repairable
and is NOT covered under warranty.

www.havis.com • 1-800-524-9900
Table of Contents
10 3
Specications
Parts Included
Port Replication Capability & Antenna Identication
Installation
Cable Management
Operation - Docking
Operation - Undocking
3
4
5
6
7
8
10
Specications
Power Supply Input 19.0V DC-In
Dimensions 11.1” ( 28.2 cm) H x 8.7” ( 22.2 cm ) W x 4.4” ( 11.1 cm ) D
Weight 2.6 lbs ( 1.18 kg )
Operating Environment -20° C to 60° C ( -4° F to 140°F )
Storage Environment -40° C to 71° C ( -40° F to 160° F )
• Do not place metal objects or containers of liquid on top of the Docking Station
• If a malfunction occurs, immediately unplug the Power Supply and remove the laptop
• Use only the specied Power Supply (Part # LPS-116) with this Docking Station
• Do not connect cables into ports other than what they are specied for
• Do not leave the Docking Station in a high temperature environment (greater than 85°C, 185°F)
for a long period of time
Precautions
Operation - Undocking
1) If previously locked, unlock Docking Station using supplied key.
2) While holding tablet with one hand, lift the Latch Handle on the top
of Docking Station.
3) Once unlatched grab both sides of tablet, rock the top forward and carefully
lift out of Docking Station, top end rst.
EC DECLARATION OF CONFORMITY in accordance with EN 50498
Manufacturers Name: Havis, Inc.
Manufacturers Address: 75 Jacksonville Road, Warminster, PA 18974 USA
Declares under our sole responsibility that the product:
Product name: Havis Docking Station For Getac F100 Fully Rugged Tablet
Model: DS-GTC-21X, where ‘X’ may be any alphanumeric character and which describes product options.
May be followed by any alphanumeric characters which describe product options.
Product Options: This declaration covers all options of the above product which bear the CE Marking.
Is in conformity with the following standards or other normative documents:
Automotive EMC Directive EN 50498:2010, Electromagnetic compatibility (EMC) -
2004/108/EC: Product family standard for aftermarket electronic equipment in vehicles
Directive 2011/65/EU Restriction of the use of certain hazardous substances (RoHS)
Supplementary Information:
The product herewith complies with the requirements of the Automotive EMC Directive 2004/108/EC, Annex I, 6.5, 6.6, 6.8,
and 6.9. This product requires the use of a recommended e-Marked automotive power supply when used within vehicles.
Warminster, PA, USA April 11, 2014 Bruce Jonik, Director of Engineering , Havis, Inc.
FCC 47CFR, Part 15 compliance: This is an FCC Class B device. Any changes or modications
to the model DS-GTC-21X not expressly approved by Havis, Inc. could void
the user's authority to operate this equipment.

4 9
Docking Station
Parts Included
Latch Handle
Ports
Front Facing USB
Mounting Locations
Latch Tab
Bumpers
Docking Connector
Barrel Lock
Mounting Holes (x4)
(VESA 75)
Strain Relief
Locator Pin
Operation - Docking
2) Hold tablet in landscape orientation, with bottom angled toward
Docking Station. Lower tablet into the bottom of the Docking Station.
3) Pivot tablet so the top aligns with the Locator Pin at the top of the
Docking Station. Lower the Latch Handle to secure tablet in place.
4) For theft deterrence, secure tablet by locking Docking Station with
supplied key (Hardware Kit Item 2).
Latch Tab will
engage in front of
F110 Tablet

8 5
Parts Included (continued)Operation - Docking
Port Replication Capability & Antenna Identication
Hardware Kit
DO NOT FORCE TABLET ONTO DOCKING STATION. IF THERE IS RESISTANCE,
CHECK ALIGNMENT OF TABLET ON DOCKING STATION.
Alignment Sockets
Back Side of Getac F110 Rugged Tablet
Alignment Posts
DS-GTC-210 Series Docking Station
NOTE: Ensure a proper connection by aligning the tablet’s
Alignment Sockets with the Docking Station’s Alignment Posts
1) Ensure Docking Station is unlatched by lifting Latch Handle.
This Hardware Kit includes:
1. Zip Ties (6)
2. Keys (2)
3. M4 x 0.7 x 25mm long
Pan Head Screws (5)
4. Split Lock Washers (5)
5. Washers, M4 (5)
Tools required for installation:
• #2 Phillips
(For M4 Pan Head Screws)
4 5
USB 2.0
(x3)
USB 3.0
(x1)
Antenna
(optional)
Power Input
Serial (x2)
DB9
HDMI Ethernet
(RJ45)
Microphone/
Speaker VGA
Antenna A: WLAN (WiFi)
Antenna B: WWAN (Cellular)
Antenna C: GPS
Parts DS-GTC-211-3,
DS-GTC-212-3, DS-GTC-213-3

www.havis.com • 1-800-524-9900
1) Tip the Docking Station to a position that is comfortable to work with.
2) Install all cables that are necessary for computing needs.
3) Use Zip Ties (Hardware Kit Item 1) and the Strain Relief Points on the bottom of
the Docking Station to secure cables and reduce risk of accidental disconnects.
4) Create a service loop with cables to ensure that no tension is on the
connectors and to enable intended motion.
5) Tie off cables onto a stationary part of the mounting system.
6 7
Installation
1) Install the Docking Station to the Motion Device using four (4) M4 x 0.7 x 25mm
long Pan Head Screws (Hardware Kit Item 3), four (4) Split Lock Washers
(Hardware Kit Item 4), and four (4) Washers, M4 (Hardware Kit Item 5).
Torque screws to 20 in-lbs (2.3Nm) ± 10%.
NOTE: If you are mounting the optional Front Exiting
USB Cable (Part # DS-DA-311), please refer
to page 11 before beginning Installation.
Washer, M4 Lock Washer M4 x 0.7 x 25mm Screw
Typical Motion Device Example
(not included)
Cable Management
Collect cables and secure
to the mounting system.
(Note: Mounting system not included)
This loop must be large enough
to allow full range of expected
rotation and extension without
stressing connections.