Havis C-VS-1800-CHGR-2 Configuration guide

C-VS-1800-CHGR-2_INST_6-17

TOOLSNEEDED:
PhillipsScrewDriver Socketset(Standard&Metric) WireCutters
WireCrimpingtool T‐20TorxBit7/16wrench
Always!
ReadallinstructionsbeforeinstallinganyHavis,Inc.products.
Checkforobstructions(Wires,brakelines,fueltank,etc.)beforedrillinganyholes!
Usehardwareprovidedwithinstallkit
QTYPARTSDESCRIPTIONPART#
1 MainConsoleHousingCM008536
1FloormountbracketCM007280
1PassengersidetrimpanelCM008542
1DriversidetrimpanelCM008541
1HVACSupportbracketCM008543
C‐HK‐326
QTYPARTSDESCRIPTIONPART#
11”GrommetGSM20093
26mmFlangenutGSM30141
1OringfordualUSBplugGSM31342
1OringforAUXpanelGSM31344
31/4"x3/4"LagboltGSM33060‐1
4#8‐18x1/4"screwGSM33178
2#10x3/4"SheetmetalscrewGSM33195
INSTALLINSTRUCTIONSC‐VS‐1800‐CHGR‐2
18”VehicleSpecificConsolefor2016‐2020DodgeCharger
PolicePursuitStreetAppearancePackage(ordercodeAEB)
With12.1‐inchlar
g
etouchscreendis
p
la
y
o
p
tion
(
ordercodeAV2
)
CM008542
CM008541
CM008543
CM007280
CM008536

C-VS-1800-CHGR-2_INST_6-17


ViewofStreetAppearancePackageChargerfull
lengthconsoleandLargetouchscreendisplay.
(OEMordercodesAEB&AV2)
Removecoverinfrontofarmrest.
UnsnapsidetrimsurroundingHVACandradio
controls.
Locatetwo(2)screwsunderHVACcontrol.
PullHVACcontrollertowardsrearofvehicleand
unplug.
Removescrewsandsetasideforfutureuse.

C-VS-1800-CHGR-2_INST_6-17




















Removerubbercoverinsidecenterconsole.
Removefour(4)OEMfasteners.
Slideconsoletowardstherearandremove.
Removeventassemblybyliftingandpulling
towards the rear of the vehicle.
RemovedualUSBassemblyoutofthebackofthe
console.
RemoveAUXmodulefromcenterconsole.
Removeentirewiringharnessfromtheconsole.
Snap HVACbracketontotheHVACandradio
controller.
InstallfrontmountingplatetoOEMstuds with
supplied6mmflangenuts.Leavelooseuntillater.

C-VS-1800-CHGR-2_INST_6-17









Installthebracketandcontrollerintothe
dashusing#10x3/4"sheetmetalscrews.
Confirmeverythingislinedupandtighten
hardware.
SlideC‐VS‐1800‐CHGR‐2consolehousingintothe
vehicletowardsthedash.
Lineuptofrontmountingplateandlooselyinstall
with1/4"x3/4"carriageboltsandserratednuts.
InstallthepreviouslyremoveddualUSBassembly
intothepassengersidetrimpanel.Installthetrim
panelusingthe#8‐18x1/4"flatheadscrews.
Installdriversidetrimpanelusing#8‐18x1/4"
Phillipsflatheadscrews.

C-VS-1800-CHGR-2_INST_6-17










Placethefrontpanelontheconsoleandplugin
theAUXcontroller
Attachfrontpanelwitheight(8)#8‐18x1/4"
flatheadscrews.
Tightenallfronthardwareatthistime.
Attachrearofconsoletofloorwith1/4"x3/4"
Lagboltsintothefactoryclipsinfloor.
Confirmfunction ofalltheOEMcontrolsincluding
USBandAUXaccessories.
Wireandmountcontrolheadsasneeded.InstallationofC‐VS‐1800‐CHGR‐2consolecomplete.