Havis C-DMM-3008 User manual

C‐DMM‐3008_INST_12‐18


INSTALLATIONINSTRUCTIONS
C‐DMM‐3008FlipUpDashMonitorMount
2019‐2020FordFusionResponder
TOOLSREQUIRED:
RatchetWrench Dashpanelremovaltool OpenEndWrench‐7/16”
7mmSocket  Phillipsscrewdriver  Wirecutters
Always!
ReadallinstructionsbeforeinstallinganyHavis,Inc.products.
Usehardwareprovidedwithinstallkit
HARDWAREandPARTS:
QTY DESCRIPTIONPART#
1Upperdriversidesupportbracket  CM009533
1Upperpassengersidesupportbracket CM009534
1Lowerpassengersidesupportbracket CM009554
310‐32x1/2"MachinescrewGSM33118
3#10StarwasherGSM31034
1VESArotatorplateCM009068
1PVCwasherCM008582
21/4"PlasticwasherCM86600
21/4"SteelwasherGSM31005
21/4"NylocknutGSM30016


Notes:
TheC‐DMM‐3000swivelplateacceptsC‐MM‐301offsetbracketusedwithC‐MM‐2XXadaptors.
C‐MM‐2XXseriesadaptorbracketsarenotneededformostVESA75andotherHavisDockingStation
mountingapplications.
CM009068VESArotatorplategivesadditionalpositioningoptions,butisnotrequireddependingon
mountingpreference.

C‐DMM‐3008_INST_12‐18


C‐DMM‐3008
Assembly
CM009534
Passengersideupper
supportbracket
CM009533
Driversideupper
supportbracket
CM009554
Passengersidelower
supportbracket
CM009068
VESArotatorplate
CM008582
PVCwasher
CM86600‐1/4"Plasticwasher
GSM31005‐1/4"Steelwasher
GSM30016‐1/4"Nylocknut
GSM33118‐10‐32x1/2"screw
GSM31034‐#10Starwasher

C‐DMM‐3008_INST_12‐18


Viewofdashcenterinstrumentpanel
Attachpassengersidelowersupportbracketto
dashusingOEMlowerradiomountscrew.
(
7mmsocket
)

Carefullypartiallyremovelowercenterandside
trimpanels.Itisnotnecessarytocompletely
removeandunplugpanels.
Carefullyremoveuppercentertrimbezel using
plasticpaneltool.
Attachpassenger sideuppersupportbracket
usingOEMupperradiomountscrew.
(
7mmsocket
)

Attachdriversideuppersupportbracketusing
OEMupperradiomountscrew.
(7mmsocket)

C‐DMM‐3008_INST_12‐18


Reattachlowercenterandsidetrimpanels.
Attachframetolower passengersidesupportbracket
with10‐32x1/2”screwandstarwasher.
Attachframetoupperdriversidesupportbracket
with10‐32x1/2”screwandstarwasher.
Reattachuppercentertrimbezel.

Attachframetoupperpassengersidesupportbracketwith
10‐32x1/2”screwandstarwasher.(Phillipsscrewdriver)
PlaceDMMmainframeontothesupport
brackets.

C‐DMM‐3008_INST_12‐18


AttachVESAplatetothebackofthedock.The
graynylonwasherwillgobetweenthisbracket
andtheDMMswivelplate.
Installationisnowcom
p
lete.
Dockthecomputerandtest.
Determinedesiredpositionforyourspecificcomputer
andattachtoDMMswivelplateusingnylonwashers,
steelwashers,andnylocknuts.Tightensothatthe
dockrotatessmoothly.(Firm,butnottootight)
RoutewiringalongthesideoftheDMMflipupframeusing
wiretiesandexistingholes.Testup/downandsidetoside
motiontoconfirmwireshaveadequateslackandstrainrelief.
Checkandadjustpositioningasdesired.
Testforproperlatchinginclosedposition.
Push up latch to
release and lift