Hearth & Home PHTRIM-32LINEAR User manual

1
Hearth & Home Technologies • PHTRIM-32LINEAR, PHTRIM-36LINEAR, PHTRIM-42LINEAR Instructions • 2616-971 Rev. B • 10/19
PHTRIM-32LINEAR, PHTRIM-36LINEAR, PHTRIM-42LINEAR
Models: COSMO-IFT-B Series, RAVE-IFT-B Series, JADE-B Series
Passive Heat Trim Installation Instructions
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions or Flying Debris.
Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
CAUTION! Do not install damaged components.
WARNING! Risk of Fire!
• Combustible materials MUST NOT overlap or be placed
behind a decorative front.
• DO NOT apply combustible materials beyond the
minimum clearances. Comply with all minimum
clearances to combustibles as specied. Overlapping
materials could ignite and will interfere with proper
operation of decorative fronts.
If any parts are missing or damaged, contact your dealer before
starting installation. DO NOT install a damaged kit.
Introduction
This trim kit is used with the Passive Heat Front Discharge
(PH-FRT-LINEAR) Heat Management System, which con-
veys warm air from the replace into the same room through
a front discharge opening. Installation of the Passive Heat
kit must be done in conjunction with the appliance installa-
tion. Follow instructions included with the PH-FRT-LINEAR
kit to complete installation of the Passive Heat system.
Installation of this kit MUST be performed by a qualied
service technician.
WARNING! Risk of Fire! DO NOT install the Passive Heat
system with models that are not approved. Overheating
will occur.
1. Locate hand bends on the vent back plate as shown in
Figure 1. Use a screwdriver to bend them in the same
direction as the long and short bends.The number of
hand bends may vary by appliance size.
Installation
Kit Contents
Verify and remove contents from packaging before
beginning installation.
(1) Vent Cover
(1) Vent Back Plate
(10) Screws
Figure 1 Back Plate Hand Bends
HAND BEND
Preparation
CAUTION! Risk of Burns!
• The replace should be turned off and cooled before kit
is installed.
• Shut off gas supply.

2Hearth & Home Technologies • PHTRIM-32LINEAR, PHTRIM-36LINEAR, PHTRIM-42LINEAR Instructions • 2616-971 Rev. B • 10/19
2. Install the vent back plate with the bends oriented to-
ward the wall and the longest bend on top. Attach the
vent back plate to the wall using eight screws. See
Figures 2, 4 and 5.
3. Attach the inside bends to the framing using two
screws. See Figure 5.
Figure 2 Orientation of Back Plate Bends
SHORT BEND
VENT COVER
VENT BACK PLATE
SEE DETAIL A
LONG BEND
DETAIL A
Figure 3 Attach Vent Cover to Vent Back Plate - Rear View
VENT COVER PLATE
VENT BACK PLATE
REAR VIEW
4. Attach the vent cover to the vent back plate by lining
up the hooks of the vent cover plate to the slots on the
vent back plate. Slide cover to engage hooks. See
Figure 3.

3
Hearth & Home Technologies • PHTRIM-32LINEAR, PHTRIM-36LINEAR, PHTRIM-42LINEAR Instructions • 2616-971 Rev. B • 10/19
Please contact your Hearth & Home Technologies
dealer with any questions or concerns.
For the location of your nearest Hearth & Home
Technologies dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Maintenance
Service and maintain the gas replace per instructions.
Keep the air register(s) clean and free of any blockage.
Figure 5 Attach Back Plate to Wall
4 SCREWS - TOP
4 SCREWS - BOTTOM
2 SCREWS - SIDES
BENDS TOWARD WALL
LONG BEND
SHORT BEND
WALL
Figure 4 Back Plate Orientation
Painting
If desired nishing includes a painted register cover and
screws, 100% acrylic latex paint with compatible primer
is recommended.
NOTICE: The location of the Passive Heat discharge
opening could allow for venting and other construction
materials to be visible. It is acceptable to paint the vent pipe
and other construction materials using a high temperature
paint with a minimum of 300 °F continuous exposure rating.
Hearth & Home Technologies recommends using black
touch up paint (part number TUP-GBK-12) available from
your Hearth & Home Technologies dealer.