Hearth & Home 550-TRIM3-BK-B Manual

1
Hearth & Home Technologies • Trim Kit Instructions • 2115-951 Rev. E • 6/19
Leave this manual with party responsible for use
and operation.
550-TRIM3-BK-B, 550-TRIM4-BK-B,
750-TRIM3-BK-B, 750-TRIM4-BK-B
Installation & Operating Instructions
1. Remove parts from package and lay face down on
a non-abrasive, stable, at surface. The upper and
lower J-Hooks and tabs must be straightened as
shown in Figure 2 and Figure 3 because they are
shipped at. See Figure 5 for a visual reference and
measurements for each individual trim kit.
2. Connect the top, bottom, and sides by aligning the
holes on the left and right side pieces with the thread-
ed studs on the top and bottom pieces. The four-
piece trim kit is shown in Figure 1. When installing the
three-piece trim kit, align the top piece with the sides
in the same manner.
3. Secure the two nuts at each corner using a 3/8 in.
wrench or nut driver. See Figure 2.
Figure 1. Assemble Components - TRIM4 Shown
Figure 2. Location of J-Hook and Threaded Studs
4. Bend the tabs of the lower mounting brackets as
shown in Figure 3.
5. Hang trim kit on appliance by aligning upper J-Hooks
with top replace slots. Secure by pressing inward
and downward until trim kit sits rmly in place. Fast-
ern lower corners with included sheet metal screws.
6. If the sides of the trim pieces appear to be bent inward
away from replace wrap sides, loosen hex nuts, re-
move assembled trim piece and gently bend sides
outward slightly. While keeping the side trim pieces
pushed outward, replace and tighten the hex nuts.
7. Hang the rescreen decorative front on appliance.
See Figure 4.
Note: If an overlap front is used, attach trim kit before
attaching door front mounting brackets. The front
will overlap the trim kit.
STRAIGHTEN
J-HOOKS AS
SHOWN
(BOTH SIDES)
THREADED
STUDS
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.

Hearth & Home Technologies • Trim Kit Instructions • 2115-951 Rev. E • 6/19
2
Figure 4. Trim Kit Installed
Figure 3. Lower Left Tab
STRAIGHTEN AND BEND
LOWER TAB AS SHOWN
(BOTH SIDES)

3
Hearth & Home Technologies • Trim Kit Instructions • 2115-951 Rev. E • 6/19
45-1/4 IN.
42 IN.
750-TRIM4-B
750-TRIM3-B
38-3/16 IN.
45-1/4 IN.
34-5/8 IN.
40-5/16 IN.
550-TRIM3-B
40-5/16 IN.
38-1/2 IN.
550-TRIM4-B
Figure 5. Trim Kit Dimensions
3-7/8 IN.
FLOOR
4-3/8 IN. MIN.
550-TRIM4-B/750-TRIM4-B
= APPLIANCE
OUTLINE
Figure 6.
Note: The dimension from the bottom of the appliance to
the bottom of the surround is 3-7/8 inches as shown
in Figure 6. It is recommended that the appliance be
installed to allow for a minimum of 4-3/8 inches from
bottom of appliance to bottom of surround.
Please contact your Hearth & Home Technologies dealer with any questions or concerns.
For the location of your nearest Hearth & Home Technologies dealer,
please visit www.hearthnhome.com.
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com