Hearth & Home LOGS-2129 User manual

Hearth & Home Technologies • Log Placement Instructions • 2129-935 Rev. C • 2/17 1
CAUTION! Logs are fragile! Carefully remove the logs and cardboard tray from the inside of the fireplace. See Figure
Remove the microfoam and inspect the logs for damage. Inspect the four factory installed logs for damage. Locate the
pilot in order to verify your position in relation to the appliance. See Figure 2.
Log Set Assembly: LOGS-2129
Models: GDST4336I, GDFL4136I, GDCL4136I, GDCR4136I,
GBST4336I, GBFL4136I, GDST4336IFT, GDFL4136IFT,
LCOR-DV36IN, RCOR-DV36IN
LOG PLACEMENT
INSTRUCTIONS
Figure 2. Factory Installed Logs and Pilot Position
STEP 1. Log #1 (SRV2129-704): Place Log #1 on Log A. The end and bottom of Log #1 fit into the indentation on
Log A highlighted in Figure 3. The Y-shaped end of Log #1 will rest on the smooth area of Log B as shown in Figure 4.
CAUTION: DO NOT reposition logs that have been
factory installed! Follow these instructions to position
the logs that were packaged separately.
Figure 4. Placement of Log #1
1
1
HUMP
HUMP
C
C
1
1
2
2
3
3
A
A
B
B
C
C
D
D
Figure 1. Log Assembly Location
Figure 3. Placement of Log #1
B
B
A
A
1
1
1
1
A
A
PILOT
PILOT
PILOT
PILOT
PILOT
PILOT
Models: GDST4336I, GDFL4136I, GDCL4136I, GBST4336I, GBFL4136I
GDST4336IFT, GDFL4136IFT, LCOR-DV36IN
(For Models GDCR4136I and RCOR-DV36IN, see next page .)
Log Set Components

Hearth & Home Technologies • Log Placement Instructions • 2129-935 Rev. C • 2/172
STEP 2. Log #2 (SRV2129-705): Locate portion of Log #2 that is highlighted in Figure 5. Place that portion of Log
#2 on the indentation on Log C. Log #2 will rest on the tip of Log B. Slide the bottom of Log #2 up to the edge of the burner
as shown in Figure 6.
Figure 6. Placement of Log #2
2
2
STEP 3. Log #3 (SRV2129-707): Place Log #3 so that it rests on the indentations located on Log #2 and Log D.
Log 3 should extend beyond Log #2 by one inch.
Figure 8. Placement of Log #3
Figure 5. Placement of Log #2
Figure 7. Placement of Log #3
B
B
C
C
D
D
B
B
2
2
BURNER EDGE
BURNER EDGE
1 in.
1 in.
2
2
PILOT
PILOT
PILOT
PILOT
PILOT
PILOT
PILOT
PILOT
3
3
2
2
D
D
Model: GDCR4136I and RCOR-DV36IN
STEP 1. Log #1 (SRV2129-704): Place Log #1 on Log A. The end and bottom of Log #1 fit into the indentation on
Log A highlighted in Figure 9. The Y-shaped end of Log #1 will rest on the smooth area of Log B as shown in Figure 10.
Figure 9. Placement of Log #1 Figure 10. Placement of Log #1
1
1
A
A
1
1
A
A
B
B
B
B

Hearth & Home Technologies • Log Placement Instructions • 2129-935 Rev. C • 2/17 3
Figure 11. Placement of Log #2 Figure 12. Placement of Log #2
Figure 13. Placement of Log #3 Figure 14. Placement of Log #3
STEP 2. Log #2 (SRV2129-705): Locate portion of Log #2 that is highlighted in Figure 11. Place that portion of
Log #2 on the indentation on Log C. Log #2 will rest on the tip of Log B. Slide the bottom of Log #2 up to the edge of the
burner as shown in Figure 12.
C
C
2
2
B
B
BURNER
BURNER
EDGE
EDGE
C
C
2
2
B
B
1 in.
1 in.
2
2
D
D
3
3
3
3
STEP 3. Log #3 (SRV2129-707): Place Log #3 so that it rests on the indentations located on Log #2 and Log D.
Log 3 should extend beyond Log #2 by one inch.