Hearth & Home LOGS-I30 User manual

1
Heat & Glo • LOGS-I30 Log Instructions • 2206-935 Rev. D • 12/16
Log Set Assembly: LOGS-I30
Models: Supreme-I30, Supreme-I30-SP, Supreme-I30AU, Supreme-I30-C, Supreme-I30-NZ
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2206-701): Bend the log tab into the upright position as shown in
Figure 1. Position Log #1 as shown in Figure 2. The left end of the log should rest on the log support. Mate the right end of the log
with the right grate tine. Rotate log clockwise, until the right end of the log engages the right grate tine, and the left end of the log
touches the log tab shown in Figure 1.
Figure 1. Figure 2. Install Log #1
Figure 3. Log #2 Figure 4. Place Log #2
Log #2 (SRV2206-705): Position Log #2 as shown in Figure 3. Mate the slot located on the bottom of Log #2 (Figure 4) with the
log pin located on the surface of the burner. Rotate the right end of Log #2 clockwise, until it comes into contact with the grate tine.
LOG
SUPPORT
FLAT SPOTS
FOR LOG #4
MATE SLOT WITH LOG PIN
GRATE TINE FITS IN
LOG GROOVE
LOG RESTS ON
GRATE TINE
1
2
SRV2206-701 SRV2206-702
#1 #3
SLOT
2
LOG TAB
LOG SUPPORTS
LOG PIN
GRATE TINES
PILOT ASSEMBLY
SRV2206-703 SRV2206-704#4 #5
SRV2206-706 SRV2206-705
#2
#6

Heat & Glo • LOGS-I30 Log Instructions • 2206-935 Rev. D • 12/162
Log #3 (SRV2206-702): Position Log #3 as shown in Figure 5. Position the grate tine groove, located on the bottom of the
log, over the base of the left grate tine. Pull the log forward. The back end of Log #3 rests on the log support. Bend the tab
located to the left of the pilot assembly into the vertical position. Rotate the end of Log #3 clockwise until the bottom right
corner contacts the log tab.
Figure 5. Place Log #3
Log #5 (SRV2206-704): Position Log #5 as shown in Figure 7. See Figure 6 for additional details. Mate the grate tine with
the log groove as shown. Position the tips of Log #5 on the at spots as shown in Figure 6.
Log #4 (SRV2206-703): Position Log #4 as shown in Figure 6. See Figure 3 for additional references. Place the thick end
of Log #4 on the large at spot on Log #1. Rest the front end of Log #4 on the at spot of Log #2.
FLAT SPOTS
(FOR LOG #6)
POINTS OF LOG REST ON
FLAT SPOTS
GRATE TINE
TOUCHES
LOG GROOVE
Figure 7. Position Log #5
Figure 8. Position Log #6
Log #6 SRV(2206-706): Position Log #6 as shown in Figure 8. See Figure 7 for additional references. Rest the left end of
Log #6 on the at spot of Log #3. Position the nose of Log #6 on the fork of Log #5.
FRONT END OF LOG
RESTS ON FLAT
SPOT
REST LOG ON
LARGE FLAT
SPOT
LEFT END OF
LOG RESTS ON
FLAT SPOT
POSITION THE NOSE ON THE
FORK OF THE LOG
CORNER OF
LOG FLUSH
WITH LOG TAB
3
5
4
6
Figure 6. Place Log #4
Figure 9. Log Set Installed
FLAT SPOTS
FOR LOG #5