Hearth & Home RAVE3012I User manual

1
Hearth & Home Technologies • Glass Panel Installation Instructions • 2264-940 Rev. i • 1/17
BAC
SMOOTH SURFACE MUST FACE OUT
LONG SIDE (LEFT & RIGHT)
SHORT SIDE (LEFT AND RIGHT)
LOWER PANEL
Glass Panel Installation Instructions
Models: RAVE3012I, SLR32, RAVE4013I-C, SLR-C, SLR-D,
XLR-PLUS-AU, RAVE4013I-D, XLR-PLUS-AUB
NOTICE: Handle refractory panels with care. Refractory
may chip or crack if dropped or impacted.
TOOLS
Screw gun equipped with 1/4 in. socket or
1/4 IN. wrench or socket
KIT COMPONENTS
(1) Left Refractory Panel
(1) Right Refractory Panel
(1) Back Refractory Panel
(4) Glass Retaining Brackets
Screws
Leave this manual with party responsible for use
and operation.
1. Install back glass panel labeled A as shown in Figure
1. Back panel will be held in place by the side panels.
Hold back panel in place while installing the left / right
panels per steps 2 and 3.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
Figure 1. Placement of Glass Panels
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation. Sheet metal
edges are sharp.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
Note: Install left and right glass panels with the
longer side to the front of the appliance as noted in
Figure 1.
Note: If the lower panel is finished, the glass baffle
will need to be removed on SLR-C, RAVE4013I-C,
SLR-D and RAVE4013I-D models before installing
panels. Replace baffle after the glass panels have
been installed. The side media tray edges may also
need to be bent inward.
Glass Panel Instructions
CAUTION! Risk of Injury! Glass baffle MUST be re-
installed ,if removed. Appliance could overheat causing
glass to break.
2. Install left glass panel labeled B as shown in Figure 1.
Install retaining bracket with the screw provided. See
Figure 2.
SLR-C/SLR-D/RAVE4013I-C/RAVE4013I-D: Fasten
additional bracket to base pan with screw provided.
3. Install right glass panel labeled C as shown in Figure
1. Install retaining bracket with the screw provided.
See Figure 2.
SLR-C/SLR-D/RAVE4013I-C/RAVE4013I-D: Fasten
additional bracket to base pan with screw provided.

Hearth & Home Technologies • Glass Panel Installation Instructions • 2264-940 Rev. i • 1/17
2
Figure 2. Retaining Tab Installation
SCREW
GLASS PANEL
SLR32, SLR-C,
RAVE4013I-C, RAVE3012I
RETAINING BRACKET
XLR-PLUS-AU
GLASS PANEL
RETAINING BRACKET
SCREW
GLASS BAFFLE
LOWER PANEL
Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.hearthnhome.com
Please contact your Hearth & Home Technologies dealer
with any questions or concerns.
For the location of your nearest Hearth & Home
Technologies dealer, please visit www.hearthnhome.com.
Note: A slight gap will exist between the glass panel
and the inner heat shield on the SLR32 model only.