Hendi 221884 User manual

You should read this user manual carefully before
using the appliance.
Bevor Sie das Gerät in Betrieb nehmen, sollten
Sie diese Gebrauchsanweisung aufmerksam lesen.
Alvorens de apparatuur in gebruik te nemen dient
u deze gebruiksaanwijzing aandachtig te lezen.
Przed uruchomieniem urządzenia należy koniecznie
dokładnie przeczytać niniejszą instrukcję obsługi.
Lisez attentivement ce mode d’emploi avant d’utiliser
l’appareil .
Prima di utilizzare l’apparecchio in funzione leggere
attentamente le istruzioni per l’uso.
Citiţi cu atenţie prezentul manual de utilizare înainte de
folosirea aparatului.
Внимательно прочитайте руководство пользователя
перед использованием прибора.
Πρέπει να διαβάσετε αυτές τις οδηγίες χρήσης
προσεκτικά πριν χρησιμοποιήσετε τη συσκευή.
STICK BLENDER
222140, 221884, 221891, 222393

2
Keep these instructions with the appliance.
Diese Gebrauchsanweisung bitte beim Gerät aufbewahren.
Bewaar deze handleiding bij het apparaat.
Zachowaj instrukcję urządzenia
Gardez ces instructions avec cet appareil.
Conservate le istruzioni insieme all’apparecchio.
Păstraţi maualul de utilizare alături de aparat.
Хранить руководство вместе с устройством.
Φυλάξτε αυτές τις οδηγίες μαζί με τη συσκευή.
For indoor use only.
Nur zur Verwendung im Innenbereich.
Alleen voor gebruik binnenshuis.
Do użytku wewnątrz pomieszczeń.
Pour l’usage à l’intérieur seulement.
Destinato solo all’uso domestico.
Doar pentru uz la interior.
Использовать только в помещениях.
Για χρήση μόνο σε εσωτερικό χώρο.

3
EN
Dear Customer,
Thank you for purchasing this Hendi appliance. Before using the appliance for the first time, please read
this manual carefully, paying particular attention to the safety regulations outlined below.
Safety regulations
• This appliance is intended for commercial use only.
• The appliance must only be used for the purpose for which it was intended and designed.
The manufacturer is not liable for any damage caused by incorrect operation and
improper use.
• Keep the appliance and electrical plug away from water and any other liquids. In the
event that the appliance should fall into water, immediately remove plug from the socket
and do not use until the appliance has been checked by a certified technician. Failure to
follow these instructions could cause a risk to lives.
• Never attempt to open the casing of the appliance yourself.
• Do not insert any objects in the casing of the appliance.
• Do not touch the plug with wet or damp hands.
•Danger of electric shock! Do not attempt to repair the appliance yourself. In case of
malfunctions, repairs are to be conducted by qualified personnel only.
• Never use a damaged appliance! Disconnect the appliance from the electrical outlet and
contact the retailer if it is damaged.
• Warning! Do not immerse the electrical parts of the appliance in water or other liquids.
Never hold the appliance under running water.
•Regularly check the power plug and cord for any damage. If the power plug or power cord
is damaged, it must be replaced by a service agent or similarly qualified persons in order
to avoid danger or injury.
•Make sure the cord does not come in contact with sharp or hot objects and keep it away
from open fire. To pull the plug out of the socket, always pull on the plug and not on the
cord.
•
Ensure that the cord (or extension cord) is positioned so that it will not cause a trip hazard.
• Always keep an eye on the appliance when in use.
• Warning!
As long as the plug is in the socket the appliance is connected to the power
source.
• Turn off the appliance before pulling the plug out of the socket.
• Never carry the appliance by the cord.
• Do not use any extra devices that are not supplied along with the appliance.
• Only connect the appliance to an electrical outlet with the voltage and frequency
mentioned on the appliance label.
• Connect the power plug to an easily accessible electrical outlet so that in case of
emergency the appliance can be unplugged immediately. To completely switch off the
appliance pull the power plug out of the electrical outlet.

4
EN
• Always turn the appliance off before disconnecting the plug.
• Never use accessories other than those recommended by the manufacturer. Failure to do
so could pose a safety risk to the user and could damage the appliance. Only use original
parts and accessories.
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge.
•This appliance must not be used by children under any circumstances.
•Keep the appliance and its cord out of reach of children.
•Always disconnect the appliance from the mains if it is left unattended or is not in use,
and before assembly, disassembly or cleaning.
•Never leave the appliance unattended during use.
Special safety regulations
• Use the appliance only as described in this manual. Indoor use only.
• This appliance should be operated by trained personnel.
•Never let the blade face towards anybody while operating the appliance.
•Do not touch the blade and moving parts. Keep fingers, hair, clothing and utensils away
from all moving parts.
• Dry the appliance and all accessories before connecting to the power supply and prior to
attaching the accessories.
• Danger of hand injury! Handle the blade with great care as it is very sharp.
• Never add ingredients to the container while the appliance is operating.
• WARNING! Unplug immediately after use, before removing or changing accessories.
• This product is a hand-held appliance designed to process foodstuff in a container.
• All maintenance, installation and repair works should be performed by specialized
trained authorized technicians.
• WARNING: During operation, keep hands and utensils out of the container to reduce the
risk of severe personal injury and / or damage to the blender.
• Do not continuously operate the appliance to avoid overheating the motor. The continuous
operation time should not exceed over 3 minutes. Operate the appliance again, after it
has been cooled.
• Do not wash the appliance with water or waterjet. Washing with water can cause leakage
and increase the risk of electric shock. No parts are dishwasher safe.
• Lay out the power cord in such a way that no unintentional pulling or tripping over is
possible.
• Do not clean or store the machine unless it is completely cooled down.
• This appliance is classified as protection class II.

5
EN
For mounting the wall bracket of item 222393 on the wall, please read carefully below im-
portant safety precautions:
• Installation should be done by the qualified technician for the reason of safety.
• Verify prior to installation that the wall can safely support the loading of whole set of
appliance & its accessories.
• Make sure that no electrical wires, water, gas or other lines are located around the in-
stallation location.
• Consult a qualified contractor or installer for assistance if you are not certain about the
structure of the wall.
• Tighten the screws firmly but do not over tighten. Over tightening can damage the screws,
greatly reducing the holding power.
• During installation, keep away the pet and children.
• Warning! Do not put other things except the appliance to prevent overloading of the
bracket.
Intended use
• The appliance is intended for professional use.
• This appliance is intended only for pureeing,
emulsifying and mixing hot and cold food com-
mercially. It allows for preparation of soups, pu-
ree, creams, marzipan mass, cheese creams,
etc. directly in the pot. Any other use may lead to
damage to the appliance or personal injury.
• Operating the appliance for any other purpose
shall be deemed a misuse of the appliance. The
user shall be solely liable for improper use of the
appliance.

6
EN
Product description
Variable speed
knob (option)
ON/OFF button
Safety button
Locking button
Plastic housing
Whisk
(only 222393 supplied)
Blender shaft
(not supplied)
221884 with an additional
blender shaft (not supplied)
221891 with an additional
blender shaft (not supplied)
222393 with 400mm blender shaft
ON/OFF button
Carbon brush
cover
Plastic
housing
Blender
shaft
Variable speed knob
222140

7
EN
Main technical parameters
Model: 222140 Model: 221884 / 221891
A
C
B
D
C
C
C
D
B
A
Technical Specifications
Code Supply
voltage
Power Approx.
rotation speed
Approx. weight of main
unit excluding blending
shaft or whisk
A
(Length)
B
(Diameter)
222140 230 V/50 Hz 220 W 4,000 ~ 20,000 rpm 1.15 kg 304 mm Ø 75 mm
221884 230 V/50 Hz 350 W 4,000 ~ 16,000 rpm 2.35 kg 416 mm Ø 100 mm
221891 230 V/50 Hz 500 W 4,000 ~ 16,000 rpm 2.55 kg 416 mm Ø 100 mm
Remark: Technical specifications are subject to change without prior notice.
Combination table for the Blender shaft and whisk accessories. Below accessories are not included:
Code Approx.
weight
C
(Length)
D
(Diameter)
Description
222164 0.81 kg 185 mm –Whisk for 222140 (optional)
– 0.46 kg 160 mm Ø 25 mm Blender shaft for 222140 (supplied)
222263 0.86 kg 250 mm – Whisk for model 221884 (optional) and 221891 (optional)
222225 0.82 kg 250 mm Ø 35 mm
Blender shaft for 221884 (optional) and 221891 (optional)
222232 1.02 kg 300 mm Ø 35 mm
222249 1.28 kg 400 mm Ø 35 mm
222256 1.56 kg 500 mm Ø 35 mm
Remarks: Set of item 222393 = 221884 + 222249 + 222263 + wall bracket + installation kits (2 sets of mounting
screws, washers and expansion bolts).

8
EN
Introduction
• Read this Operation Manual carefully before using
the appliance. It contains important for your safe-
ty as well as operating and maintenance advice.
• This appliance is for professional use in ice-
cream shops, restaurants, hotel kitchens for pre-
paring ice-cream mixes, vegetable soups, purees,
sauces, stuffing, mayonnaise, tomato paste, pes-
to, etc.
• If you wish to make the best use of the stick
blender functions, you must be thoroughly famil-
iar with its performance and operating features.
• Maintenance requires just a few simple opera-
tions that may be performed by the operator.
• To ensure a long life and minimize operating
costs, follow the instructions given in this manual.
• The manufacturer has designed the Immersion
Blender to ensure safe operating conditions.Re-
moval of protections installed by the manufactur-
er will seriously undermine the guaranteed safety
conditions.
• To ensure safety, comply with the instructions re-
garding installation and connection of the device
to the power supply.
• The device must be installed in a work environ-
ment free of corrosive agents.
• The installation area must not be potentially ex-
plosive.
• Use only supplied SPARE PARTS.
• This Operation Manual is an integral part of the
Immersion Blender and must be kept in a safe
place. The features, information and drawings
published herein are the exclusive property of the
manufacturer.
• The appliance functions make it possible to pre-
pare in the minimum time the following types
of food: thick vegetable purees, soups, mashed
potatoes, creams, batters, doughs, mayonnaise,
almond pulp, cream cheese etc.
Preparations before bracket mounting on the wall (For item: 222393 only)
Before installation: Check the wall bracket for any damage & the completeness of the installation kits (2 set
of mounting screws, washers and expansion bolts included). DO NOT install if any missing or damage.
Note:
• Consult a qualified contractor or installer for as-
sistance if you are not certain about the structure
of the wall and ensure that the procedure is car-
ried out properly and safely.
• Installation work should be done by qualified
technicians for the reason of safety.
• The distance between the holes of mounting
screws is about 217mm. Make clear the sur-
rounding before installation.
• Important: Before starting bracket mounting on
the wall, make sure you have all the tools, such
as screw driver, electric drills, measuring tape,
marking pencil (All are not included).
• The bracket must be securely anchored on a wall
by attaching two mounting screws with the ex-
pansion bolts inserted.
• Be aware of the items such as ducts, electrical
wires and water pipes that hide behind the walls
in your work area. Special care is required during
installation.

9
EN
Operating instructions (Model: 222140)
CAUTION: Before connecting the appliance to the power supply, check that the power supply voltage corre-
sponds with the power supply details shown on the rating label.
REMARK: There is no lock function for continuous operation for this model 222140.
Operating the appliance:
1. Ensure that the appliance is disconnected from
the power supply before assembly.
2. Connect the blending shaft/whisk to the main
unit.
3. Check that the ON/OFF button (1) is in the
released (flat) position.
4. Connect the appliance to the power supply.
5. Then, press the ON/OFF button (1). The appliance
will turn on. BE CAREFUL!
6. To turn off the appliance, release the ON/OFF
button (1).
1
2
Operating instructions (Model: 221884, 221891, 222393)
CAUTION: Before connecting the appliance to the power supply, check that the power supply voltage corre-
sponds with the power supply details shown on the rating label.
REMARK: There is lock function for continuous operation for the model 221884 & 221891.
Starting and stopping the appliance
1. Ensure that the appliance is disconnected from
the power supply before assembled.
2. Connect the blending shaft/whisk to the main
unit.
3. Check that the ON/OFF button (3) is in the
released (flat) position.
4. Connect the appliance to the power supply.
5. Press and hold the Safety button (1) first.
6. Then, press the ON/OFF button (3) at the same
time. The appliance will start up. BE CAREFUL!
7. Release the Safety button (1), the appliance will
keep operating.
8. To stop the appliance, release the ON/OFF
button (3).
Continuous operating the appliance:
Follow steps 1 to 7 above, then:
• With the ON/OFF button (3) in “pressed” position,
press Locking button (4) once.
• Release the ON/OFF button (3) and the appliance
will keep operating in a continuous mode.
• To turn off the appliance, press and release the
ON/OFF button (3).

10
EN
Variable speed operation (Model: 222140, 221884, 221891, 222393)
Follow steps 1 to 7 above, then:
• Change the speed of the motor by turning the
variable speed button (2) towards the maximum
or minimum as required. It is advisable to start
the device at a low speed when using the whisk.
With the self-regulating speed system, the se-
lected speed will remain constant even if the
consistency of your mixture changes.
REMARKS:
Blender function: For better control, we recom-
mend you hold the bender by the handle and the
bottom of the motor unit. Furthermore, we recom-
mend you tilt the bender slightly to prevent the bell
from touching the bottom of the container. Always
make sure that the bell is sufficiently immersed to
avoid splashing and that the air vents of the motor
unit do not come into contact with any liquid. For
optimum efficiency, two-thirds of the blending arm
should be immersed in the mixture being prepared.
Whisk function: You can also hold the device with
one hand the bowl with the other hand if neces-
sary. During operation we recommend you move
the whisk around in the bowl in order to ensure
that the mixture is completely homogeneous. Keep
the whisk away from the sides of the bowl. For
maximum efficiency, at least one-fifth of the whisk
length should be immersed. Never immerse the
whisk holder in the mixture.

11
EN
Assembling / Disassembly of the attachments
The assembly / disassembly operations of the appliance are performed with the appliance stopped and dis-
connected from the power supply.
Assembly: Model 222140:
1. Align and insert the coupling (5) of the blending
shaft (3) or the whisk (6) in the clutch (2) of the
main unit (1).
2. Screw thoroughly the blending arm (3) or whisk
(6) to the main unit (1).
Assembly: Model 221884, 221891, 222393:
1. Align and insert the coupling (5) of the blending
shaft (3) or the whisk (4) in the clutch (2) of the
main unit (1). Make sure the narrower part of the
appliance coupling fits the concave side of the
blender shaft (3) or whisk (4) arm coupling.
2. Screw the nut (6) up to fasten it firmly to the main
unit (1).
Follow the above steps in the reverse order to disassembly the accessories.
Cleaning instructions
Before cleaning always unplug the appliance form
the source of power supply.
• After using the Stick Blender in a hot mixture,
cool the blending shaft in cold water before dis-
mantling the bell from the blender shaft. Clean
the shaft immediately after use to prevent adhe-
sion of the mixture.
• Never immerse the motor unit or the handle in
water; clean with a damp cloth or a sponge.
• Blender shaft and bell cleaning: Place the blend-
ing arm and the bell in a suitable container with
clean water and switch on for a few seconds.
• WARNING: Always dry the blades thoroughly after
cleaning to avoid rust spotting.
• Never immerse the whisk holder in water; clean
with a damp cloth or a sponge.
• After use clean the appliance with a detergent or
disinfectant. Do not use undiluted bleach. Do not
use alkaline detergents to clean plastic parts.

12
EN
Troubleshooting
In case of a power cut or if the device has been un-
plugged, release the ON/OFF button (3), check the
power supply and restart the device.
If the device is switched off due to overheating, re-
lease the ON/OFF button (3), and unplug the de-
vice, wait a few minutes for the motor to cool down
and the thermal safety mechanism to be reset, and
then restart the device.
If the cause of the problem cannot be determined:
release the ON/OFF button (3), unplug the device,
check below:
1. the plug
2. that the blades are free to rotate in the bell,
3. that state of the power cord,
4. the drive shaft is free to rotate. To this end, re-
move the bell and test the rotation of the end of
the drive shaft manually.
If a malfunction occurs which is listed in this op-
eration manual, consult your retailer or return the
device to the after-sales service.
Electrical diagram
Model 222140
AC230V
PC
BM
NO
NO
Variable Resistor
Motor
Switch
Model 221884, 221891, 222393
Safety
button Lock
AC 230V 50Hz
L
N
Variable Resistor
M
PCB
Start

13
EN
Exploded drawing & part list for model 222140
Model 222140
12456
7
910 11
12
10
9
13 14
15 16 17
19
18
16 20
22
23 25
29-1
31
21
27
24
22
29-2
29-3
29-4
29-5
29-6 30
28
3
26
8
18-1
Part list – model 222140 main unit and blender shaft
Part
No.
Part Name Part
No.
Part Name Part
No.
Part Name
1Blade 14 Plastic head housing 26 Pressing board screw
2Convex ring 15 Spline sleeve 27 Switch osculant staff
3Graphite ring spring 16 Bearing 28 Housing screw
4 Graphite ring 17 Rotor 29-1 Screw plunger 28-1
5Ceramic ring 18 Brush barrel 29-2 Screw plunger 28-2
6Ceramic ring sleeve 18-1 Brush cover 29-3 Screw plunger 28-3
7Knife protector 19 Brush 29-4 Screw plunger 28-4
8Bearing sleeve 20 Stator 29-5 Screw plunger 28-5
9 Seal ring 21 PCB Speed control board 29-6 Screw plunger 28-6
10 W688Z Bearing 22 Left and right housing 30 Cable sheath
11 S/S tube 23
Rubber interlocking protector 31 Power cord
12 Output axis 24 Pressing board
13 Spline 25 Speed control key

14
EN
Exploded drawing & part list for model 221884, 221891, 222393 (Main unit only)
12
3
4
5
67
8910 11 12
131415
16
181920
21222324
25
26
17
27
Part list – model 221884, 221891, 222393 (main unit only)
Part No. Part Name Part No. Part Name Part No. Part Name
1 Power cord 10 Air outlet cover 19 Ring
2 Cable tie 11 Pressing board screw 20 Air outlet cover
3 Switch 12 Housing 2 21 Housing 4
4 Pressing board screw 13 Spline sleeve 22 Locking button
5 Pressing board screw 14 Bottom motor cover 23 Switch osculant staff
6 PCB control panel 15 Motor 24 Switch sheath
7 Housing 1 16 Upper motor cover 25 Pressing board
8 Screw plunger 17 Pressing board screw 26 Speed control key
9 Pressing board screw 18 Housing 3 27 Safety button

15
EN
Blender shafts (Optional) for model 221884 & 221891
1
3
6
7
8
6
9
4
10
11
13
15
16
2
5
12
14
4
4
4
Part list – blender shafts (optional): 222225, 222232, 222249, 222256
Part
No.
Part Name Part
No.
Part Name Part
No.
Part Name
1 Spline sleeve 7 Output axis (Different length
depend on different model)
13 Graphite ring
2 Spline sleeve seal ring 8
304 S/S tube (Different length
depend on different model)
14 Graphite ring spring
3Connect sleeve 9Bearing sleeve 15 Convex ring
4 Connect sleeve seal ring 10 Knife protector 16 Blade
5Fastening sleeve 11 Ceramic ring sleeve
6 608 bearing 12 Ceramic ring

16
EN
Whisk (Optional) for model 222140
1
2
3
4
5
6
3
4
8
9
11
12
13
2
14
15
16
17
18
19
20
21
22
23
24
25
26
10
7
27
2
28
2
Part list – whisk (optional): model 222164
Part
No.
Part Name Part
No.
Part Name Part
No.
Part Name
1 Spline sleeve 11 Needle bearing 21 Oil sealing
2 Ø8 Snap ring 12 Screw 22 M4x5 Screw
3Bearing washer 13 Ø16 Snap ring 23 Cylindrical pin
4Bearing 14 Helical gear bearing 24 Fixed board
5Connect sleeve 15 Cylindrical pin 25 Steel ring
6Helical gear bearing 16 Straight gear 26 Steel bar
7 Screw plunger 2 17 Key 27 Baffle plate
8 Screw plunger 1 18 Output axis 28 Screw
9Housing screw 19 Shaft sleeve
10 Upper cover 20 Lower cover

17
EN
Whisks (Optional) for model 221884 & 221891
3
4
5
6
7
8
5
6
10
11
13
14
15
4
1
6
17
18
19
20
21
22
23
24
25
26
27
28
12
9
29
4
4
30
1
2
Part list – whisk (optional): model 222263
Part
No.
Part Name Part
No.
Part Name Part
No.
Part Name
1Fastening sleeve 11 Housing screw 21 Shaft sleeve
2 Spline sleeve seal ring 12 Upper cover 22 Lower cover
3 Spline sleeve 13 Needle bearing 23 Oil sealing
4 Ø8 Snap ring 14 Screw 24 M4x5 Screw
5Oil sealing 15 Ø16 Snap ring 25 Cylindrical pin
6Bearing 16 Helical gear bearing 26 Fixed board
7Connect sleeve 17 Cylindrical pin 27 Steel ring
8Helical gear bearing 18 Straight gear 28 Steel bar
9 Screw plunger 2 19 Key 29 Baffle plate
10 Screw plunger 1 20 Output axis 30 Screw

18
EN
Warranty
Any defect affecting the functionality of the ap-
pliance which becomes apparent within one year
after purchase will be repaired by free repair or re-
placement provided the appliance has been used
and maintained in accordance with the instructions
and has not been abused or misused in any way.
Your statutory rights are not affected. If the appli-
ance is claimed under warranty, state where and
when it was purchased and include proof of pur-
chase (e.g. receipt).
In line with our policy of continuous product devel-
opment we reserve the right to change the product,
packaging and documentation specifications with-
out notice.
Discarding & Environment
When decommissioning the appliance, the prod-
uct must not be disposed of with other household
waste. Instead, it is your responsibility to dispose to
your waste equipment by handing it over to a des-
ignated collection point. Failure to follow this rule
may be penalized in accordance with applicable
regulations on waste disposal. The separate col-
lection and recycling of your waste equipment at
the time of disposal will help conserve natural re-
sources and ensure that it is recycled in a manner
that protects human health and the environment.
For more information about where you can drop off
your waste for recycling, please contact your local
waste collection company. The manufacturers and
importers do not take responsibility for recycling,
treatment and ecological disposal, either directly
or through a public system.

19
DE
Sehr geehrte Kundin, sehr geehrter Kunde,
wir danken Ihnen für den Kauf des Gerätes Hendi. Machen Sie sich bitte mit dieser Anleitung noch vor der
Inbetriebnahme des Gerätes vertraut, um Schäden durch die unsachgemäße Bedienung zu vermeiden. Den
Sicherheitsregeln ist besondere Aufmerksamkeit zu widmen.
Sicherheitsregeln
• Die unsachgemäße Bedienung des Geräts kann zur schweren Beschädigung des Geräts
sowie zu Verletzungen führen.
• Dieses Gerät ist nur für den gewerblichen Gebrauch bestim.
• Das Gerät ist ausschließlich zu dem Zweck zu benutzen, zu dem es hergestellt wurde.
Der Hersteller haftet nicht für Schäden, die auf unsachgemäße Bedienung des Geräts
zurückzuführen sind.
• Den Kontakt des Gerätes und des Steckers mit Wasser oder einer anderen Flüssigkeit
vermeiden. Den Stecker unverzüglich aus dem Stecker ziehen und das Gerät von einem
anerkannten Fachmann prüfen lassen, wenn das Gerät unbeabsichtigterweise ins Was-
ser fällt. Bei Nichteinhaltung dieser Sicherheitsvorschriften besteht Lebensgefahr.
• Nie eigenständig das Gehäuse des Gerätes zu öffnen versuchen.
• In das Gehäuse des Gerätes keine Gegenstände einführen.
• Den Stecker nicht mit nassen oder feuchten Händen berühren.
•Gefahr eines Stromschlags! Das Gerät darf nicht selbstständig repariert werden.
Sämtliche Mängel und Unzulänglichkeiten sind ausschließlich durch qualifiziertes Per-
sonal zu beseitigen.
• Niemals ein beschädigtes Gerät benutzen! Das beschädigte Gerät vom Netz trennen
und sich mit dem Verkäufer in Verbindung setzen.
• Warnung: Die Elektroteile des Gerätes dürfen weder in Wasser noch in andere Flüssig-
keiten getaucht werden. Ebenso ist das Gerät nicht unter fließendes Wasser zu halten.
• Der Stecker und die Stromversorgungsleitung sind regelmäßig auf Beschädigungen zu
prüfen. Der beschädigte Stecker oder Leitung sind an eine Servicestelle oder einer an-
deren qualifizierten Person zur Reparatur zu übergeben, um eventuellen Gefahren und
Verletzungen des Körpers vorzubeugen.
• Man muss sich davon überzeugen, ob die Stromversorgungsleitung weder mit scharf-
kantigen noch mit heißen Gegenständen in Berührung kommt; halten Sie die Leitung
weit entfernt von einer offenen Flamme. Um den Stecker aus der Netzsteckdose zu neh-
men, muss man immer am Stecker und nicht an der Leitung ziehen.
• Die Stromversorgungsleitung (oder Verlängerungsleitung) ist vor dem zufälligen Heraus-
ziehen aus der Steckdose zu schützen. Die Stromversorgungsleitung muss so geführt
werden, dass niemand zufällig darüber stolpern kann.
• Das Gerät muss während seiner Anwendung ständig kontrolliert werden.
• Warnung! Wenn der Stecker in der Netzsteckdose ist, muss man das Gerät als an die
Stromversorgung angeschlossen betrachten.
• Bevor der Stecker aus der Netzsteckdose genommen wird, ist das Gerät auszuschalten.

20
DE
• Das Gerät darf beim Tragen nicht an der Leitung gehalten werden.
• Benutzen Sie kein Zubehör, das nicht mit diesem Gerät mitgeliefert wurde.
• Das Gerät muss man ausschließlich an die Steckdose mit solch einer Spannung und
Frequenz anschließen, wie auf dem Typenschild angegeben wird.
• Stecken Sie den Stecker in die Steckdose, die an einem leicht und bequem zugänglichen
Ort angeordnet ist, und zwar so, dass das Gerät bei einer Störung sofort abgeschaltet
werden kann. Um das Gerät vollständig auszuschalten, muss man es von der Stromquel-
le trennen. Zu diesem Zweck muss man den Stecker, der sich am Ende der vom Gerät
getrennten Leitung befindet, aus der Netzsteckdose ziehen.
• Vor dem Abtrennen des Steckers ist das Gerät auszuschalten!
• Benutzen Sie kein Zubehör, das nicht vom Hersteller empfohlen wird. Die Anwendung
vom nicht empfohlenen Zubehör stellt eine Gefahr für den Nutzer dar und kann zur Be-
schädigung des Gerätes führen. Benutzen Sie ausschließlich Ersatzteile und Zubehör im
Original.
• Dieses Gerät eignet sich nicht für den Gebrauch durch Personen (gilt auch für Kinder)
mit geringerer Motorik, Sensorik oder geistiger Fähigkeit oder mangelhafter Erfahrung
und Wissen.
• Auf keinen Fall darf das Bedienen des Gerätes durch Kinder zugelassen werden.
• Das Gerät mit Stromversorgungsleitung ist außerhalb der Reichweite von Kindern zu
lagern.
• Ebenso muss dafür gesorgt werden, dass die Kinder das Gerät nicht zum Spielen benut-
zen.
• Das Gerät ist immer dann von der Stromversorgung zu trennen, wenn es ohne Aufsicht
bleiben soll bzw. auch vor der Montage, Demontage und Reinigung.
• Während der Nutzung darf das Gerät nicht ohne Aufsicht gelassen werden.
Besondere sicherheitshinweise
• Verwenden Sie das Gerät nur wie in diesem Handbuch beschrieben. Verwenden Sie das
Gerät nur in Innenräumen.
• Dieses Gerät sollte von geschultem Personal bedient werden.
• Während des Betriebes darf man die Schneide nicht auf sich in der Nähe befindende
Personen richten.
• Während des Funktionsbetriebes darf man weder die Schneide noch die anderen beweg-
lichen Teile berühren. Während des Funktionsbetriebes darf man nicht die beweglichen
Teile mit der Hand als auch mit den anderen Küchengeräten berühren; die Haare zu-
sammenbinden.
• Das Gerät und sein Zubehör müssen vor dem Anschluss an die Stromquelle und der
Montage des Zubehörs genau getrocknet werden.
• Es besteht die Gefahr von Verletzungen der Hand! Man muss vorsichtig sein – das
Messer ist scharf.
• Geben Sie während des Funktionsbetriebes keine Zutaten in das Gefäß.
• Warnung: Nach dem Gebrauch und vor dem Abnehmen bzw. Ändern des Zubehörs ist