HIK VISION DS-TPE100 User manual

Control Terminal’s User Manual
User Manual
UD.6L0201D1989A01
Control Terminal- TPE100

Control Terminal’s User Manual
1
User Manual
COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the
properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries
(hereinafter referred to be “Hikvision”). This user manual (hereinafter referred to be
“the Manual”) cannot be reproduced, changed, translated, or distributed, partially or
wholly, by any means, without the prior written permission of Hikvision. Unless
otherwise stipulated, Hikvision does not make any warranties, guarantees or
representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to Control Terminal DS-TPE100.
The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only.
The information contained in the Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the latest version in the company
website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of
Hikvision in various jurisdictions. Other trademarks and logos mentioned below are
the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE
PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND
FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,

Control Terminal’s User Manual
2
FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF
THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING,
AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS
INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN
CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF
PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL
NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL OPERATION,
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL
RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT
IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE
LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS
PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE
APPLICABLE LAW, THE LATER PREVAILS.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance

Control Terminal’s User Manual
3
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the EMC Directive
2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper
recycling, return the battery to your supplier or to a designated collection point. For
more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

Control Terminal’s User Manual
4
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings:
Do not drop the device or subject it to physical shock.
Proper configuration of all passwords and other security settings is the
responsibility of the installer and/or end-user.
In the use of the product, you must be in strict compliance with the electrical
safety regulations of the nation and region. Please refer to technical specifications
for detailed information.
Input voltage should meet both the SELV (Safety Extra Low Voltage) and the
Limited Power Source with 100~240 VAC, 48 VDC or 12 VDC according to the
IEC60950-1 standard. Please refer to technical specifications for detailed
information.
Do not connect several devices to one power adapter as adapter overload may
cause over-heating or a fire hazard.
Please make sure that the plug is firmly connected to the power socket.

Control Terminal’s User Manual
5
If smoke, odor or noise rise from the device, turn off the power at once and
unplug the power cable, and then please contact the service center.
Cautions:
Read the manual carefully before you use the device.
Make sure the device power is turned off and the plug is unplug from the power
socket when you do the operations, including plug or remove the board card.
Make sure the device power is turned off when plug or unplug any cables.
Wait at least 30 seconds to power on the device if the device is newly shut down
to avoid the device damage by frequent power off/power on.
For some precise unit is quite sensitive to the ESD, make sure electrostatic
discharge has been finished if you want to dismount or assemble the device.
If no ESD workbench is provided, you can follow the tips below to lower the
damage might be caused by ESD.
oWear a wrist strap, and touch the metal parts of the device with the wrist
strap.
oTouch the metal part on the machine instead of the components.
oAvoid the unnecessary walking around.
oHold the edge of the components, especially for the board card.
oPut all the components on a conducting foam pad.
oMove the components on the workbench as less as possible.
It is recommended that you use a magnetic cross screwdriver to tighten or loosen
the screws. Make sure no tool or components are left in the machine.
Keep the device away from water and any liquid.
While shipping, the device should be packed in its original packing.
Improper use or replacement of the battery may result in hazard of explosion.
Ensure unit is installed in a well-ventilated, dust-free environment.
Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit
as a result of dropping it may cause damage to the sensitive electronics within the

Control Terminal’s User Manual
6
unit.
Use the device in conjunction with an UPS if possible.
Power down the unit before connecting and disconnecting accessories and
peripherals.
A factory recommended HDD should be used for this device.

Control Terminal’s User Manual
Table of Contents
Chapter 1 About This Manual...................................................................8
Chapter 2 Introduction ..............................................................................9
2.1 Product Overview ........................................................................................9
2.2 Performance .................................................................................................9
2.3 Specification................................................................................................10
2.4 Shipping & Storage Requirement.............................................................11
Chapter 3 Installation..............................................................................12
3.1 Appearance.................................................................................................12
3.2 Dimension ...................................................................................................12
3.3 Interface Description.................................................................................13
3.4 Assembling HDD........................................................................................14
3.5 Assembling the Device...............................................................................15

Control Terminal’s User Manual
Chapter 1 About This Manual
Purpose
This document introduces the DS-TPE100 Control Terminal and relevant settings of
the product.
Intended Audience
This document is intended for:
Technical support engineers
Maintenance engineers

Control Terminal’s User Manual
Chapter 2 Introduction
2.1 Product Overview
With the features of low consumption and high performance, DS-TPE100 is designed
for entrance/exit control. Adopting the strong aluminum alloy extrusions without fans
on its body, the control terminal has a compact structure with good heat dissipation.
The control terminal is applicable to the challenging environment of dusty and high
electromagnetic interference.
Figure 2-1 Overview of Control Terminal
2.2 Performance
CPU:
Intel® CPU Bay Trail-D J1900 with integrated MC and GPU.
CS:
Intel® CPU Bay Trail-D J1900
Memory:
4GB DDR3L, with memory frequency of 1333MHz
Ethernet Interface:
10/100/1000Mbps Self-adaptive
Display:
Integrated Graphics Processing Unit
VGA, with max. resolution and fresh rate of 2560×1600@60Hz