Honeywell ADEMCO Vista-12 Series User manual

K10021ENV1 5/11 Rev. A
A
AD DE EM MC CO O V Vi is st ta a- -1 12 2 S Se er ri ie es s
User’s Guide
This control complies with EN50131-3:2009.

– 2 –
IMPORTANT: If the keypad beeps rapidly upon entering the premises,
it indicates that an alarm has occurred during your absence and an
intruder may still be on the premises. LEAVE IMMEDIATELY and
CONTACT THE POLICE from a nearby safe location.
SYSTEM COMPATIBILITY NOTICE
Your Honeywell security system is designed for use with devices manufactured or approved
by Honeywell for use with your security system. Your Honeywell security system is not
designed for use with any device that may be attached to your security system's keypad or
other communicating bus if Honeywell has not approved such device for use with your
security system. Use of any such unauthorized device may cause damage or compromise
the performance of your security system and affect the validity of your Honeywell limited
warranty. When you purchase devices that have been manufactured or approved by
Honeywell, you acquire the assurance that these devices have been thoroughly tested to
ensure optimum performance when used with your Honeywell security system.

– 3 –
Table of Contents
Table of ContentsTable of Contents
Table of Contents
Burglary System Basics ........................................................................................................ 4
Basic Features ...................................................................................................................... 4
Exit/Entry Delays ................................................................................................................. 5
Before Arming (Ready [∗] Key) ............................................................................................ 6
Bypassing Zones ................................................................................................................... 6
Basic Arming Modes............................................................................................................. 7
Disarming and Silencing Alarms......................................................................................... 8
Using the Keyswitch.............................................................................................................8
Emergency Alarms (Panic Keys) ......................................................................................... 9
Non-Alarm Functions ..........................................................................................................10
Chime Mode ........................................................................................................................ 10
Using the Voice Message Center ....................................................................................... 10
Using Macro Keys............................................................................................................... 11
System Devices ................................................................................................................... 11
Follow-Me Feature (audio beeps) ...................................................................................... 11
Advanced System Functions ............................................................................................. 13
Accessing Other Partitions ................................................................................................ 13
Defining Macro Keys .......................................................................................................... 13
Schedules............................................................................................................................. 14
Event Log ............................................................................................................................ 16
Security Codes and Authority Levels................................................................................ 18
How to Assign User Codes and Attributes........................................................................ 19
Testing and Maintaining the System ..............................................................................20
Testing the System (to be conducted weekly) ................................................................... 20
Maintaining the System..................................................................................................... 21
Trouble Conditions ..............................................................................................................22
Fire Alarm System (If Installed).......................................................................................24
Quick Guide to Basic System Functions ........................................................................ 25
Charts of Your System’s Features ....................................................................................26

– 4 –
Burglary System Basics
Burglary System BasicsBurglary System Basics
Burglary System Basics
Basic Features
Basic FeaturesBasic Features
Basic Features
Partitions •Partitions provide two independent areas of protection, with each partition
containing a group of zones that can be armed and disarmed without affecting other
zones or users.
•Partitioned systems can include a common area, which is an area shared by users of
two other partitions (such as a lobby in a building).
•Some users may be given the authority to view status and arm/disarm other
partitions.
•See Accessing Other Partitions section for details.
Zones •Each partition consists of specific protection points known as zones.
•When a zone is faulted, its zone number is displayed on the keypad for easy
identification.
Keypads •The system is controlled from the keypad, and the keypad displays system status.
•Each keypad is assigned a default partition for display purposes, and will show only
that partition's information.
•When entering codes and commands, sequential key depressions must be made
within 4-5 seconds of one another. If 4-5 seconds elapse without a key depression,
the entry will be aborted and must be repeated from its beginning.
•If you make a mistake while entering a security code, stop, press the [∗] key, and
then start over. If you stop in the middle while entering a code, and then
immediately start the entry over, an erroneous code might be entered.
Keypad Lockout: The system may have been programmed to lockout the keypads
for 15 minutes if more than 30 keystrokes (within a 15 minute period) are made
without a valid user code plus command being entered. The message “Code
Sabotage” is displayed during the lockout period.
Voice Keypads •Voice Keypads (if installed), are functionally the same as other keypads.
•Voice announcements of system status (see Before Arming section)
•Voice chime, which can alert you to the opening of doors and windows while the
system is disarmed (see Voice Chime in Chime mode section)
•Message center, which lets you record and playback messages (see Using the Voice
Message Center in the System Overview section).
Security Codes •Your installer assigned you a security code at the time of installation. This code is
required to perform most system functions.
•Each security code can have a different authority level which defines the functions
each user can perform. Refer to the Security Code section for details on adding and
changing security codes.
Arm/Disarm •You can arm your system in several different modes, depending on whether you are
staying in or leaving the premises.
•To arm the system, simply enter your security code followed by the desired arming
mode key.
•To disarm the system, enter your security code followed by [1] OFF.
•Refer to the Arming/Disarming sections for specific arming commands.

– 5 –
E
EE
Exit/Entry Delays
xit/Entry Delaysxit/Entry Delays
xit/Entry Delays
Exit Delay •When you arm the system, the system gives you a programmed amount of time to
leave through the designated exit door and/or certain other zones (if programmed)
without setting off an alarm.
•A slow beeping, if programmed, will sound during the exit delay period until the last
10 seconds, which then changes to fast beeping.
•If programmed, the keypad displays a countdown of the number of seconds of exit
delay remaining.
•When exit delay expires, all zones become protected and cause an alarm if opened.
•Your system may have been programmed such that exit delay remains in effect until
a final zone (e.g. exit door) has been closed for five seconds. Ask your installer.
Exit Delay •
••
•Press the [∗
∗∗
∗] key if armed in STAY mode to restart the exit delay timer.
Restart •This gives you time to open the entry/exit door to let someone in after arming
STAY. The system
(if programmed) automatically re-arms when exit delay expires, which avoids having to disarm the
system and then re-arm it again.
•When the system is armed AWAY, reopening and closing the entry/exit door before
exit delay time expires (e.g., reentering to get a forgotten item) will restart the exit
delay time.
Entry Delay •Gives you time to disarm the system when you re-enter through the designated
entrance door. You must disarm the system before the entry delay period ends, or an
alarm will occur.
NOTE: When entry delay is active (ex. opening the entry door), the entry delay time
applies to all burglary zones in that partition.
•See your installer for your delay times.
Partition 1 Partition 2 Common Partition
Delay 1: _______ seconds Delay 1: _______ seconds Delay 1: Same as Partition 1
Delay 2: _______ seconds Delay 2: _______ seconds Delay 2: Same as Partition 1
Exit Alarms •If an entry/exit door or interior zone is faulted when the exit delay ends (e.g., exit
door left open), the system sounds an alarm and starts the entry delay timer.
•Disarming the system before entry delay ends stops the alarm sound .
•The message "ALARM CANCELED" or "CA" is displayed on the keypad, along with
a zone number indicating the faulted zone.
•No message is sent to the Central Monitoring Station.
•If you do not disarm the system before the entry delay ends, and an entry/exit door
or interior zone is still open, the alarm sound continues and an "exit alarm" message
is sent to the Central Monitoring Station. The message ""EXIT ALARM" or "EA" and
the faulted zone number is displayed on the keypad.
•To stop the alarm, the system must be disarmed (your code plus OFF); to clear the
display, enter your code plus OFF a second time.
•An “exit alarm” also results if an entry/exit door or interior zone is faulted within
two minutes after the end of the exit delay.
To clear an exit alarm:
•Make the open zone intact, then
•Enter your code plus [1] OFF to clear the display.
Your system may have been programmed for this feature to minimize false alarms sent
to the Central Monitoring Station. Ask your installer if "Exit Alarm" is active in your
system. If so, check this box: [ ]
Part. 1: _____ sec
Part. 2: _____ sec
Common: Same as
Part. 1

– 6 –
Before Armi
Before ArmiBefore Armi
Before Arming (Ready [
ng (Ready [ng (Ready [
ng (Ready [∗
∗∗
∗] Key)
] Key)] Key)
] Key)
Not Ready •
••
•Before arming the system, you should close or bypass all protected doors, windows
and
(using [∗
∗∗
∗] key) other protection zones.
•
••
•Press [∗
∗∗
∗] to display open zones (do not enter code first).
•
••
•To bypass zones, see the Bypassing Zones section below.
•Some systems, if programmed, may allow arming even if selected zones in the exit
route are faulted. Depending on the programming, these zones, if left faulted when
exit delay expires, will either be automatically bypassed or cause an alarm. See your
installer.
Voice Status: •Voice Keypads (if installed), can announce system status and faulted zones (up to 3
zone descriptors) if Voice Status is on.
•To turn Voice Status on/off: [#] + [0] [2] [4]
(also turns on Voice Chime mode; see Chime mode section)
•To announce System Status: Press [∗
∗∗
∗] STATUS key once.
•To announce faulted zones: Press the [∗
∗∗
∗] STATUS key a second time within 5
seconds of the first press
Ready •All zones are closed or bypassed and you can now arm the system.
•Some systems, if programmed, may allow arming even if selected zones in the exit
route are faulted. Depending on the programming, these zones, if left faulted when
exit delay expires, will either be automatically bypassed or will cause an alarm. See
your installer for your system’s programming.
Bypassing Zones
Bypassing ZonesBypassing Zones
Bypassing Zones
Bypass Notes •
••
•You can bypass zones before arming the system or while the system is already armed.
•Your system may have a limit on the total number (1-7) of zones you may bypass
(check with your installer).
•Bypassed zones are unprotected and will not cause an alarm if violated.
•The system will not allow fire zones to be bypassed.
•Zones are automatically unbypassed when the system is disarmed.
•Vent Zones: Your system may have certain windows set as “vent” zones, which are
automatically bypassed if left open when arming the system (you do not need to
manually bypass them). However, if a vent zone window is closed after arming, it
becomes protected and will cause an alarm if opened again while the system is armed.
To Bypass •
••
•Security code + [6] BYPASS + zone numbers
Zones •Use 2-digit zone number(s) for the zone(s) to be bypassed.
•Single digit zone numbers must be preceded by a zero (e.g. 05, 06).
•When finished, the keypad will momentarily display a "Bypass" message for each
bypassed zone number.
•Wait for all bypassed zones to be displayed, then arm the system as usual.
•When armed, “ZONE BYPASSED” is displayed with the arm message.
•
••
•To display bypassed zones prior to arming, enter your security code and press the [6]
BYPASS key.
Quick Bypass •
••
•Security Code+ [6] BYPASS + [#]
•Wait for all bypassed zones to be displayed, then arm the system.
Active? ____ •In a few moments, all open zones will be displayed and automatically bypassed. Make
sure that only those zones that you wish to leave unprotected are bypassed, and that
there are no other zones unintentionally left open.
•Allows you to easily bypass all open (faulted) zones without having to enter zone
numbers individually. This feature is useful if, for example, you routinely leave
certain windows open when arming at night.

– 7 –
Basic Arming Modes
Basic Arming ModesBasic Arming Modes
Basic Arming Modes
Stay •Security code + [3] (STAY)
•Causes: three beeps, armed STAY displayed, ARMED indicator lights
•Arms perimeter sensors, but interior sensors are left disarmed.
•Use when you want to arm the system with persons staying inside (or if you have pets
that are moving throughout the premises).
•Alarm sounds if any protected window or non-entry/exit door is opened.
•Persons entering later can enter through an entry/exit door, but they must disarm the
system within the entry delay period to avoid sounding an alarm.
Night-Stay •Security code + [3] + [3]
(Internal) •Causes: three beeps, NIGHT-STAY displayed, ARMED indicator lights
•Same as Stay mode, plus pre-selected interior sensors, while other interior sensors
are left disarmed.
•Use Night-Stay (internal) mode to provide increased security while staying inside.
•Persons entering later can use an entry/exit door but they must disarm the system
and must not violate any of the programmed interior zones to avoid sounding an
alarm.
•IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed
and cause an alarm if anyone enters those areas (e.g., waking in the middle of the
night). To avoid sounding an alarm, you must disarm the system before any activity
takes place in those zones.
Instant •Security code + [7] (INSTANT)
•Causes: three beeps, armed INSTANT displayed, ARMED indicator lights
•Arms same as Stay mode but with entry delay off.
•Use when staying inside and do not expect anyone to use an entry/exit door.
•An alarm sounds immediately if any protected perimeter window or any door is
opened, including entry/exit doors.
•IMPORTANT: Arming in this mode greatly increases the chance of false alarms. Use
extreme care in selecting this mode of arming.
Away •Security code + [2] (AWAY)
•Causes: beeping during exit delay, armed AWAY displayed, ARMED indicator lights
•Arms entire system (interior and perimeter).
•Use when nobody will be staying inside (including pets).
•An alarm sounds if a protected window or any door is opened, or if any movement is
detected inside your premises.
•When reentering through an entry/exit door, you must disarm the system within the
entry delay period to avoid sounding an alarm.
Maximum •Security code + [4] (MAXIMUM)
•Causes: same as Away mode; arms same as Away mode, but entry delay is off.
•Use when arming/disarming is being done from the outside (e.g. RF keyfob)
Step Arming •Press designated key A, B, C, or D, if programmed, once, twice or three times
depending on the arming mode desired. Each key press increases the level of security.
•First press: arm STAY; second press: arm Night-STAY; third press: arm AWAY
Quick Arm •Press [#] + arming command key, if programmed.
•This feature lets you press [#] in place of the security code when arming the system.
•The security code must always be used to disarm the system.
Function Key •Press and hold the assigned function key for 2 seconds, if programmed.
Arming •You do not need to enter your security code before pressing the arming key.
•Arms in designated arming mode. See your installer for the designated functions.

– 8 –
Disarming and Silencing Alarms
Disarming and Silencing AlarmsDisarming and Silencing Alarms
Disarming and Silencing Alarms
Disarming •Security code + [1] OFF
•The “READY” indicator lights if all zones are secure
•The keypad emits a single tone to confirm that the system is disarmed.
To Silence a •Security code + [1] OFF
Burglary Alarm •The “READY” indicator lights if all zones are secure
•The keypad emits a single tone to confirm that the system is disarmed.
To Silence a •Simply press the OFF key
Fire Alarm •The “READY” indicator lights if all zones are secure
•The keypad emits a single tone to confirm that the system is disarmed.
Memory of •When an alarm condition occurs, the keypad displays the number(s) of the zone(s)
Alarm that caused the problem, and displays the type of alarm.
•To Clear Alarm Display: Security code + [1] OFF again
•Note the zone in alarm on the keypad display, and make that zone intact (close door,
window, etc.).
•The message remains displayed even after disarming the system, but can be cleared
with another “disarm” sequence.
IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, the keypad will beep
rapidly upon your entering, indicating that an alarm has occurred during your absence.
LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location
Using the Keyswitch
Using the KeyswitchUsing the Keyswitch
Using the Keyswitch
GREEN RED
keyswitch-001-V1
•Your system may be equipped with a keyswitch for arming and disarming.
•To arm in AWAY mode: Turn the key to the right for 1/2 second and release.
Keypads beep twice and the red indicator lights or flashes.
•To arm in STAY mode: Turn the key to the right and hold for more than 1
second, then release. Keypads beep three times and the red indicator lights or
flashes.
•To disarm the system: Turn the key to the right and release. The red light
turns off.
Green Light: •Lights when the system is disarmed and ready to be armed (no open zones).
•If the green light is off, the system is not ready (one or more zones are open).
Red Light:
•Lights or flashes when system is armed in AWAY or STAY mode. See your
installer for the meanings of the lit red light:
•Lit Steady = system armed AWAY or STAY and exit delay has expired
•Flashing = system armed STAY and exit delay timer active
•Rapid Flashing = an alarm has occurred (memory of alarm)

– 9 –
Emergency Alarms (Panic Keys)
Emergency Alarms (Panic Keys)Emergency Alarms (Panic Keys)
Emergency Alarms (Panic Keys)
Your system maybe programmed to use special keys to manually activate emergency (panic) functions.
Silent Alarm •Sends silent alarm signal to monitoring station.
•Causes no audible alarm or change in display indicating that a silent alarm has been
initiated.
Audible
Alarm
•Sends audible alarm signal to monitoring station.
•Causes a loud, steady alarm at keypad(s) and at any external sounders that may be
connected.
Personal
Alarm
•Sends emergency alarm signal to monitoring station.
•Causes steady alarm sound at keypad(s), but not at external bells or sirens.
Fire Alarm •Sends fire alarm signal to monitoring station.
•Causes temporal (pulsing) sound at external bells and sirens.
To use an
Emergency
Key
•Press and hold down for at least 2 seconds whichever lettered key on the keypad has
been programmed for the desired emergency function.
OR
Briefly press both keys of the assigned key pair at the same time
•See your installer for the functions that have been programmed for your system.
6164-010-V0
1
OFF
4
MAXIMUM
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
CPU
ARMED
READY
A
B
C
D
ZONE 95
ZONE 96
ZONE 99
Lettered Panic Keys
1
OFF
4
MAXIMUM
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
CPU
ARMED
READY
6164-011-V0
PRESS BOTH KEYS
OF DESIRED PAIR
AT THE SAME TIME
ZONE 95
ZONE 99
ZONE 96
Panic Key Pairs

– 10 –
Non
NonNon
Non-
--
-Alarm Functions
Alarm FunctionsAlarm Functions
Alarm Functions
Chime Mode
Chime ModeChime Mode
Chime Mode
Chime mode alerts you to movement within the premises while the system is disarmed.
Chime Mode on •Security code + [9] (Chime message appears)
•keypads sound three beeps whenever a protected door, window or other specified
zone is opened.
•Pressing the [∗] READY key will display the open protection points.
Chime Mode off •Security code + [9] again (Chime message disappears)
Voice Chime: •You can set the Voice Keypads (if installed) to announce faulted (opened) entry/exit
or perimeter zones whenever normal Chime mode is on.
Voice Chime •[#] + [0] [2] [4] (normal Chime mode must be on first)
on/off •When Voice Chime is on, faulted zones cause a voice status announcement,
chime and display.
•When off, the sounder still provides chime if normal Chime mode is on.
Using the Voice Message Center
Using the Voice Message CenterUsing the Voice Message Center
Using the Voice Message Center
The Voice Keypads feature a voice message center that lets you record and playback one message.
Basic Information
•The message can be up to 2.5-minutes long
•The message remains in the keypad’s memory until a new
message is recorded.
•The volume control of the message is adjustable.
•Refer to the procedures below when using the Message
Center functions.
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
ARMED
READY
6160V-00-005-V0
MESSAGE
MIC
RECORD VOLUME PLAY
STATUS VOICE FUNCTION
VOLUME
KEY
VOICE
KEY
STATUS
KEY
FUNCTION
KEY
DOWN
VOLUME
PLAY KEY
AND
UP VOLUME
RECORD
KEY
SPEAKER
LCD
DISPLAY
MICROPHONE
LEDs
Message Center Functions
Record a Message •[#] FUNCTION + [0] VOICE + [1] RECORD (red MESSAGE LED lights)
•Message remains in memory until a new message is recorded.
End Recording •[1] RECORD (red MESSAGE LED flashes, indicating message waiting)
Play a Message •[#] FUNCTION + [0] VOICE + [3] PLAY
•The recorded message plays and the red MESSAGE LED turns off.
Adjust the Volume •[#] FUNCTION + [0] VOICE + [2] VOLUME keys,
•then press volume key [3] ↑(up) or [6] ↓(down)
•Adjusting message volume also adjusts status volume.
•Volume cannot be adjusted while playing.