Honeywell ADEMCO VISTA-12A Assembly instructions

K10022-1V1 10/05 Rev. A
ADEMCO VISTA-12A
ADEMCO VISTA-12E
Security Systems
Installation and Setup Guide

ii

iii
Table Of Contents
•••••••••••••••••••••••••••••••••
Features and Installation Highlights .............................................................................................. 1-1
Capabilities ........................................................................................................................................ 1-1
Functions............................................................................................................................................ 1-1
Compatible Devices............................................................................................................................ 1-2
Important Installation Highlights (Installer Please Read) .............................................................1-2
Mounting and Wiring the Control.................................................................................................... 2-1
Cabinet and Lock ............................................................................................................................... 2-1
Mounting the PC Board..................................................................................................................... 2-2
Wiring to Keypads ............................................................................................................................. 2-3
Sounder (Siren) Connections............................................................................................................. 2-5
Wiring the AC Transformer .............................................................................................................. 2-5
Backup Battery .................................................................................................................................. 2-6
Earth Ground ..................................................................................................................................... 2-6
Basic Wired Zones.............................................................................................................................. 2-8
Smoke Detectors ................................................................................................................................ 2-9
4219/4229 Expansion Zones .............................................................................................................. 2-10
6164 Keypad Expansion Zones.......................................................................................................... 2-11
Installing the RF Receiver................................................................................................................. 2-12
Installing a 5800TM Module ............................................................................................................. 2-13
Installing the Transmitters............................................................................................................... 2-13
Installing a Keyswitch ....................................................................................................................... 2-14
Connecting Relay Modules ................................................................................................................ 2-15
Powerline Carrier Devices................................................................................................................. 2-16
Trigger Module and On-Board Triggers ........................................................................................... 2-17
Phone Line Connections .................................................................................................................... 2-18
Alternative Communications Media (ACM) Connections ................................................................ 2-18
Audio Alarm Verification Connections (AAV, “Listen-In”) .............................................................. 2-19
Programming Overview ..................................................................................................................... 3-1
About Programming........................................................................................................................... 3-1
Zones and Partitions.......................................................................................................................... 3-2
Keypads .............................................................................................................................................. 3-3
Wireless Receiver Transmitters, and Wireless Keys (keyfobs)........................................................ 3-3
Pager Programming........................................................................................................................... 3-4
Function Keys .................................................................................................................................... 3-4
Output Devices................................................................................................................................... 3-4
Zone Type Definitions ........................................................................................................................ 3-5
Mechanics of Programming ............................................................................................................... 3-8
Data Field Programming.................................................................................................................... 4-1
About Data Field Programming........................................................................................................ 4-1
Programming Data Fields ................................................................................................................. 4-1
System Setup Fields .......................................................................................................................... 4-1
Zone Sounds & Timing ...................................................................................................................... 4-3
Dialer Programming (∗40 – ∗55) ....................................................................................................... 4-4

iv
System Status Report Codes ............................................................................................................. 4-7
Miscellaneous System Fields............................................................................................................. 4-9
Pager Programming Fields................................................................................................................ 4-13
Miscellaneous System Fields............................................................................................................. 4-15
AUI Enable......................................................................................................................................... 4-19
Keypad Programming Fields............................................................................................................. 4-19
Menu Mode Programming.................................................................................................................. 5-1
About Zone Programming (∗56 and ∗58 Menu Modes) .................................................................... 5-1
∗56 Zone Programming Procedure .................................................................................................... 5-1
Completing Zone Programming ........................................................................................................ 5-5
∗58 Expert Programming Mode Procedures ..................................................................................... 5-6
Wireless Key Programming Templates ............................................................................................ 5-8
About Output Device Programming (*79/*80 Menu Mode) ............................................................. 5-12
*79 Menu Mode: Output Device Mapping ........................................................................................ 5-12
*80 Menu Mode: Defining Output Functions ................................................................................... 5-14
About Zone Lists (∗81 Menu Mode)................................................................................................... 5-17
Zone List Programming..................................................................................................................... 5-18
About Function Key Programming (∗57 Menu Mode)......................................................................5-18
Programming Function Keys ............................................................................................................ 5-19
About Descriptor Programming (*82 Menu Mode)........................................................................... 5-20
Configurable Zone Type Programming (*83 Menu Mode) ............................................................... 5-22
Programming Installer and User Schedules ....................................................................................5-23
System Communication and Operation.......................................................................................... 6-1
Panel Communication with Central Station .................................................................................... 6-1
Report Code Formats ......................................................................................................................... 6-1
Robofon 8 Format............................................................................................................................... 6-4
ADEMCO Contact ID®...................................................................................................................... 6-5
Security Codes.................................................................................................................................... 6-6
Keypad Functions .............................................................................................................................. 6-7
Panic Keys.......................................................................................................................................... 6-8
Follow-Me Feature............................................................................................................................. 6-9
Setting/Adjusting the Real-Time Clock ............................................................................................ 6-10
Various System Trouble Displays ..................................................................................................... 6-11
Testing the System............................................................................................................................... 7-1
About Test Procedures....................................................................................................................... 7-1
System Test ........................................................................................................................................ 7-1
Go/No Go Test Mode .......................................................................................................................... 7-2
Dialer Communication Test .............................................................................................................. 7-3
Automatic Standby Battery Tests..................................................................................................... 7-3
Specifications & Accessories ............................................................................................................. 8-1
SECURITY CONTROL...................................................................................................................... 8-1
COMPATIBLE DEVICES ................................................................................................................. 8-2
5800 Series Transmitter Input Loop Identification ......................................................................... 8-3
Limitations and Warranty.................................................................................................................. 9-1
Index ....................................................................................................................................................... 10-1

1-1
SECTION 1
Features and Installation Highlights
•••••••••••••••••••••••••••••••••
This manual describes the installation of both the VISTA-12A and VISTA-12E. These units
are identical except where noted.
Capabilities
•Supports 2 independent partitions, which can protect two independent areas, as if each area
had its own control.
•Supports 1 common area partition that allows either of the other two independent partitions to
arm, while leaving a common area (ex. lobby or foyer) disarmed for access into the remaining
disarmed partition.
•Supports up to 22 protection zones plus 16 keyfob zones (zones 49-64) for total of 38 zones:
-- 6 basic wired zones (zones 1-6) with optional zone-doubling/double-balanced zone feature
-- Up to 8 additional wired zones (zones 17-24) using an 8-zone 4219/4229 module.
-- Supports up to 16 wireless transmitter zones (5800 series; zones 9-24).
-- Supports up to 4 installer-configurable zone types
•Up to 16 User Level Security Codes, each with separate authority levels and partition access
Downloading: Via an IBM compatible computer, Compass downloading software, and an
ADEMCO CIA/CIA-EU modem.
Functions
•Single-button arming feature: Can use dedicated keys to arm the system AWAY or STAY
•Up to 8 Schedules, to control output devices, to determine when users have access, and/or to
auto-arm/disarm (or allow disarm) the system
•Up to 2 Keypad macros, which can be activated by wired/wireless keypads
•Paging feature allows certain system conditions to be reported to up to 2 pager phone
numbers; can use a dedicated key on keypads to send a signal to a pager
•User programmable telephone number for audio “beeps” reporting of alarms to the user
(follow-me feature).
•Built-in Telephone Line Monitoring option can monitor the telephone line voltage and can
cause a local display, or a display and trouble/alarm sound.
•Event Logging records up to 254 selected events in a history log; control and readout from the
log is done via ADEMCO Compass Downloader software or using an installer/master code at
an alpha display keypad for local display.
•Installer-customized zone descriptors for all zones (useful only when using alpha display
keypads).
•Optional siren supervision detects external sounder wiring short or open; causes a trouble
condition, keypad display, and sends a report to the central monitoring station, if enabled.
•Optional RF jam detection for wireless systems detects a condition that may impede proper RF
reception (i.e., jamming or other RF interference); causes keypad display, sends a report to the
central monitoring station (if trouble reporting is enabled), and can optionally send a tamper
alarm if detected during the armed mode.
•Individual user code selection for open/close reporting to central monitoring station (set when
adding a user code, attribute 6).

Installation and Setup Guide
1-2
Compatible Devices
•Supports up to 8 Addressable Keypads: 6148/6150 Fixed-Word Display Keypads, 6164 Alpha
Keypad, 6128RF/6128RFH/6150RF/6160RF Keypad/Transceivers, 6160V Voice Keypad
•Supports up to two (2) Touch Screen (AUI) Devices (Symphony, 6270), which are in addition to
the standard eight (8) addressable keypads.
•Supports a 4219 or 4229 addressable basic wired zone expander module
•Supports 5881/5883 series receiver and 5800 series transmitters
•Outputs up to 4 relays, two on-board triggers, and/or Powerline Carrier Devices (X-10 type)
-- Use any combination of 4204, 4229, 6164 relays and/or Powerline Carrier Devices.
-- Output functions (up to 12)
•Alarm power output provides a 12VDC, 2 AMP output that can drive compatible sounders with
a steady output for burglary/panic, or temporal pulse (3 pulses – pause – 3 pulses – pause – 3
pulses.) for fire. Uses current limiting circuitry for protection.
•Auxiliary Power Output: 12VDC, 700mA maximum, including output triggers.
•Backup Battery: Rechargeable (sealed lead-acid type) 12VDC, 6AH minimum.
•Audio Alarm Verification (using AAV module, such as ADEMCO UVS); can be used in
conjunction with an output trigger to permit voice dialog between an operator at the central
station and a person at the premises.
•Alternative Communication Media: Primary telephone number messages can be reported via
ECP connection to Ethernet TCP-IP Internet/Intranet Network Modules, or other network
interfaces (e.g., EUREKA)
•AC Power Supply:
VISTA-12A: Plug-in 230VAC power pack, XF1 Model No. 60844CK, Ap11V/99090/E148-36
VISTA-12E: 220VAC wired-in transformer, 16.5VAC 25VA
Important Installation Highlights (Installer Please Read)
•This system uses addressable keypads and a Zone Expander Module (see table of addresses in
Programming Overview section).
•Keypads must be set for addresses 16-23 (first keypad is address 16, which is different from
previous controls) and programmed in data fields *190-*196.
•Zone Expander Module must be set for specific address (08), based on the zone numbers used
(see table of addresses in 4219/4229 Expansion Zones section).
•4204 Relay Module must be set for specific address (13; see Connecting Relay Modules section).
•6164 Keypads must be set for two addresses: a keypad address and a zone expander address (if
using the keypad’s expansion zones).
•This control will not power-up unless AC mains is connected (will not power-up on battery
alone). However, once the system is powered up, it will operate on battery power in the event
of AC mains loss.
•Relays have two programming menu modes: Use *79 Menu mode to map module addresses
and device (output) numbers. Use *80 Menu mode to define the output functions (see Output
Device Programming section).
•This system supports programmable function keys. Use *57 Menu mode to define the function
keys (see Function Key Programming section).
•This system provides various paging features. Refer to the Programming Overview section
for a summary on pager programming.

Mounting and Wiring the Control
2-1
SECTION 2
Mounting and Wiring the Control
•••••••••••••••••••••••••••••••••
This section describes the procedures for mounting and wiring this control and its peripheral devices.
In the following subsections, procedures are listed in the left column, while notes and pertinent
explanations are provided in the right column.
Cabinet and Lock
1. Mount the control cabinet to a sturdy
wall in a clean, dry area, which is not
readily accessible to the general public,
using fasteners or anchors (not
supplied) with the four cabinet
mounting holes.
2. Remove cabinet door, then remove the
lock knockout from the door. Insert the
key into the lock.
3. Position the lock in the hole, making
certain that the latch will make contact
with the latch bracket when the door is
closed. When correctly positioned, push
the lock until it is held securely by its
snap tabs.
Notes
•The cabinet can be closed and secured without a
lock by using 2 screws in the cover's edge.
CABINET DOOR
BOTTOM
LOCKED
UNLOCKED
cab_lock_snap-001-V0
ADEMCO ADEMCO
PUSH
SNAP
TAB
SNAP
TAB
PUSH
ON LOCK
UNTIL IT
IS SEATED
SECURELY
STEP 2STEP 1
CHECK
POSITION
Figure 1. Installing the Cabinet Lock

Installation and Setup Guide
2-2
Mounting the PC Board
NOTE: The door of the metal cabinet may be
removed to make it easier to install the PC board.
Remove the door as follows:
1. With the cabinet laying on a flat surface,
swing open the door to its full-open position.
2. Slide the door out of its retaining slots in the
cabinet and store in a safe place.
3. Remove standoff (part number K0380) from
the hardware bag and insert it into the square
hole in the back of the cabinet so that it will
align behind the lower left mounting hole in
the PC board.
4. Insert top of circuit board into slots at top of
cabinet. Make sure that circuit board rests in
slots as indicated in the diagram shown
below.
5. Swing base of circuit board onto the raised
cabinet tab and standoff.
6. Secure the sides of the PC board to the
enclosure using the 2 screws provided.
Notes
•Before installing the cabinet's contents, remove
the metal cabinet knockouts required for
wiring entry. Do not remove the knockouts
after the circuit board has been installed.
V12D-001-V0
1 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 21 22 23 25
Figure 2. Mounting the PC Board

Mounting and Wiring the Control
2-3
Wiring to Keypads
1. Connect keypads to the control’s keypad
terminals as shown on the Summary of
Connections diagram.
Determine wire size using the Wiring Run
Chart below.
If power supervision is required, refer to the
Aux Power Supervision Connections
paragraph at right.
2. Set keypad addresses. Refer to the address
setting instructions included with the keypads
and set each keypad device address according
to the chart at right.
3. Program the keypad addresses, partition
assignments and sound options in data fields
*190-*196.
NOTE: Each keypad must be assigned a
unique address, starting at address 16.
Keypads programmed with the same address
will give unpredictable results.
Supplementary Power (optional)
1. Connect as shown. Be sure to connect the
negative (–) terminal on the power supply unit
to terminal 4
(AUX –) on the control.
+–
+
456 7
SUPPLEMENTARY
POWER SUPPLY
–
CONTROL TERMINAL STRIP
AUX. AUX. DATA
IN
DATA
OUT
IMPORTANT:
MAKE THESE
CONNECTIONS
DIRECTLY TO
SCREW
TERMINALS AS
SHOWN.
TO KEYPAD RED POWER WIRE (V+)
TO KEYPAD BLK GROUND WIRE (V-) TO KEYPAD YEL DATA WIRE (<) TO KEYPAD GRN DATA WIRE (>) TO KEYPAD BLK GROUND WIRE (V-) TO KEYPAD RED POWER WIRE (V+) TO KEYPAD GRN DATA WIRE (>) TO KEYPAD YEL DATA WIRE (<)
pwr_sup_conn-008-V0
Figure 3. Using a Supplementary Power Supply
Notes
•Typical Fixed-Word Display:
6128RF/6148/6150/6150RF/6150V
•Typical Alpha Display: 6160/6160V/6164
•The system supports up to 8 keypads, which
can be assigned to partitions in any
combination
(see program fields *190-*196).
•For single 4-wire runs, determine the current
drain of all units, then refer to the Wiring
Run chart to determine the maximum length
that can be safely used for each wire size.
•Use supplementary power if the control’s aux.
power load for all devices exceeds 700mA.
Suggested power supply: AD12612
Aux Power Supervision Connections
To supervise aux power:
1. Use the Trigger Module terminals for
ground and +12V connections (instead of
main board terminals 4 and 5). See
Trigger Module and On-Board Triggers
section (page 2-17) for instructions on
mounting the Trigger Module.
2. Connect the SUPV terminal to a zone (+)
terminal.
3. Program that zone as a configurable zone
type programmed as a 24-hour zone and
with the desired report code (CID code 312
is recommended).
TOUCH SCREEN KEYPAD (AUI) NOTES:
•
••
•Use of up to two AUI devices (e.g., 6270, Symphony)
is independent from standard keypads and does not
affect the number of standard keypads the system
can support.
•
••
•AUI devices must be set for either address 1 or
address 2, depending on which unit is enabled in
field *189.
•
••
•To ensure proper AUI device operation, connect
only to controls having microprocessor version 3.0
or higher, and use AUI devices with the following
rev levels: 6270 series use version 1.0.9 or higher;
8132/8142 (Symphony) series use version 1.1.175 or
higher.

Installation and Setup Guide
2-4
Keypad Addresses
Keypad Address Keypad Address
no. 1 16** no. 5 20
no. 2 17 no. 6 21
no. 3 18 no. 7 22
no. 4 19 no. 8 23
** The first keypad is address 16, which is always
enabled and set for partition 1 with all sounds on.
Keypads powered from supplies
that do not have a backup battery
will not function if AC mains
power is lost. Make sure to power
at least one keypad in each
partition from the control’s
auxiliary power output.
Wiring Run Chart For Devices* Drawing Aux Power From The Control (12V+ & 12V–)
TOTAL CURRENT DRAIN OF ALL DEVICES CONNECTED TO A SINGLE WIRE RUN
Wire Size 50mA or less 100mA 300mA 500mA 600mA
0.6mm O.D. 152m 76m 24m 15m 13m
0.8mm O.D. 228.6m 116m 40m 24m 20m
1mm O.D. 396m 198m 67m 40m 35m
1.2mm O.D. 457m 305m 100m 70m 52m
* Includes Keypads, RF Receivers, Zone Expander/Relay Units, or TeleCommand Phone Module.
Maximum wire lengths for any device that is wired directly to the control can also be determined from the Wiring Run
Chart, based on the current drain of that device alone.
The length of all wire runs for all partitions combined must not exceed 457m when unshielded quad conductor cable is
used (228m if shielded/screened cable is used). This restriction is due to the capacitive effect on the data lines when
quad cable is used.