Horizon Fitness 5.0 R User manual

5.0R RECUMBENT BIKE OWNER’S MANUAL

3 ENGLISH
32 FRANÇAIS
62 ESPAÑOL

3
RECUMBENT BIKE OPERATION

4
2 ft
60 cm
2 ft
60 cm
2 ft 60 cm
2 ft 60 cm
FRONT
REAR
BIKE
HOW TO MOVE THE RECUMBENT BIKE
Due to the weight of the Recumbent Bike, it is
recommended that two people move it. While one person
lifts the back of the Recumbent Bike, the second person
firmly holds the handlebar and tips the Recumbent Bike
forward until it rolls on the wheels. Carefully move the
Recumbent Bike to the desired location and then lower it.
If the Recumbent Bike rocks on the floor after being set
down, turn the leveling feet underneath the front or rear
stabilizer until the rocking motion is eliminated.
To reduce the risk of injury, use extreme caution
while moving the Recumbent Bike. Do not attempt
to move it over uneven surfaces and make sure
there’s a clear space of 24 inches (minimum) on all
sides of the equipment.
WARNING
LOCATION OF THE
RECUMBENT BIKE
Place the Recumbent Bike on a
level surface. There should be
2 feet (60 cm) of each side
surround the Recumbent Bike.
Do not place the cycle in any
area that will block any vent or
air openings. The Recumbent
Bike should not be located in
a garage, covered patio, near
water or outdoors.
Leveling Feet

5
A
A
B
HOW TO ADJUST THE RECUMBENT BIKE
The Recumbent Bike can be adjusted for maximum comfort
and exercise effectiveness. The instructions below describe one
approach to adjusting the Recumbent Bike to ensure optimal user
comfort and ideal body positioning; you may choose to adjust the
Recumbent Bike differently.
SEAT ADJUSTMENT
Proper seat height helps ensure maximum exercise
efficiency and comfort, while reducing the risk of injury.
Adjust the seat height to make sure it’s in proper
position, one that keeps a slight bend in your knee while
your legs are in the extended position.
A. Seat Horizontal Position
Rotate the adjustment lever counterclockwise to slide
the seat forward or backward as desired. Rotate the
lever clockwise to lock the position. Test the seat slide for
proper operation.
B. Pedal Straps
Place the ball of the foot into the strap until it‘s
centered over the pedal, reach down and pull the
pedal strap up to tighten prior to use. To remove your
foot from the strap, loosen the strap and pull out.

6
READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS
EXERCISE BIKE. IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY
INSTRUCTIONS.
•CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult
your physician before continuing.
•Use this exercise bike for its intended purpose as described in this manual. Do not use attachments that have not been
recommended by the manufacturer.
•Never operate the exercise bike if it is not working properly, or if it has been damaged. Contact Customer Tech Support or
the authorized dealers for examination and repair.
•Do not use the exercise bike without proper footwear. NEVER operate the exercise bike with bare feet.
•Do not wear any clothing that might catch on any moving parts of this exercise bike.
•Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.
•Do not dismount the exercise bike until the pedals are at a complete STOP.
•Do not attempt to ride the exercise bike in a standing position at high RPMs until you have practiced at slower speeds.
•Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other
potentially moving part of the exercise bike.
•Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by
Customer Tech Support or the authorized dealers.
•Do not operate where aerosol (spray) products are being used or when oxygen is being administered.
•Close supervision is necessary when used near children, invalids or disabled people.
•When the exercise bike is in use, young children and pets should be kept at least 3 meters / 10 feet away.
•Ensure that adjustment levers (seat and handlebar fore-and-aft) are properly secured and do not interfere with range of
motion during exercise.
WARNING

7
ASSEMBLY
There are several areas during the assembly process that special attention must be paid. It is very important to follow the
assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed
correctly, the Recumbent Bike could have parts that are not tightened and will seem loose and may cause irritating noises.
To prevent damage to the Recumbent Bike, the assembly instructions must be reviewed and corrective actions should be
taken.
Before proceeding, find your Recumbent Bike’s serial number located on
the front stabilizer of the cycle and enter it in the space provided below.
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:
» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.
» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.
SERIAL NUMBER:
MODEL NAME: HORIZON RECUMBENT BIKE
WARNING

8
Tablet holder
Console (32)
Seat slider rail (34)
Seat slider cover (24)
Seat cushion (23)
Bottle holder
Transport wheels
Front Stabilizer (21F)
Rear Stabilizer (21R)
Crank arms (38 L&R)
Power Adapter
Pedals (37 L&R)
Pedal Straps (39 L&R)
Seat slider knob (36)
Seat Frame (35)
Back Rest (22)
Console Handlebar
Handlebar set (30)
Heart rate sensor
Fan
Console Mast (33)
Mast Cover (26)
Main frame (20)
MODEL INFORMATION

9
MAIN PARTS INCLUDED:
Main Frame (20)
Front Stabilizer (21F)
Rear Stabilizer (21R)
Handlebar Set (30)
Mast Cover (26)
Console (32)
Console Mast (33)
Pedal Set (37&39 L&R)
Seat Set (22, 23, 30, 34, 35 & 36)
Seat Slider Cover (24)
Power Adapter
Rear Cover Bracket (27)
PARTS PACKING
INCLUDED:
1 Hardware Kit
1 Owner’s Manual
HARDWARE KIT:
PRE ASSEMBLY
If you have questions or if there are any missing
parts, contact Customer Tech Support. Contact
information is located on the back panel of this
manual.
UNPACKING
Due to the weight of the Recumbent Bike, it is recommended that two people
perform the assembly. Unpack the product where you will be using it. It is
recommended that you place a protective covering on your floor. Place the carton
on a level flat surface and remove all packing materials; do not dispose of the
packing materials until assembly is completed.
NOTE: During each assembly step, ensure that ALL nuts and bolts are in place
and partially threaded in before completely tightening any ONE bolt.
NOTE: A light application of grease may aid in the installation of hardware. Any
grease, such as lithium bike grease is recommended.
NEED HELP?
1
Bolt
M8x20
Qty: 4
2
Spring Washer
Ø8
Qty: 24
3
Flat Washer
Ø8
Qty: 24
5
Bolt
M10x50
Qty: 2
4
Bolt
M8x45
Qty: 8
6
Spring Washer
Ø10
Qty: 2
7
Flat Washer
Ø10
Qty: 2
8
Bolt
M8x15
Qty: 8
9
Bolt
M8x65
Qty: 2
10
Bolt
M5x10
Qty: 4
11
Bolt
M4x15
Qty: 1
Tool Kit
5mm Wrench
6mm Wrench
13/15mm Wrench
Screwdriver

10
ASSEMBLY STEP 1
1.1 Open hardware for Step 1.
1.2 Attach the Front Stabilizer (21F) and Rear
Stabilizer (21R) to the Main Frame (20) using
4 Bolts (1), 4 Spring Washers (2) and 4 Flat
Washers (3), and tighten firmly.
1
Bolt
M8x20
Qty: 4
2
Spring Washer
Ø8
Qty: 4
3
Flat Washer
Ø8
Qty: 4
21R
21F
20
1
2
3
STEP 1 HARDWARE :

11
ASSEMBLY STEP 2
2.1 Open hardware for Step 2.
2.2 Attach the Seat Cushion (23) and Seat Back
(22) to the Seat Frame (35) using 8 Bolts (4), 8
Spring Washers (2), and 8 Flat Washers (3) on
each. Tighten firmly.
2.3 Attach the Handlbar Set (30) using 2 Bolts (5),
2 Spring Washers (6), and 2 Flat Washers (7).
Tighten firmly
2.4 Attach the Seat Slider Knob (36) to the Seat
Slider Lever.
4
Bolt
M8x45
Qty: 8
3
Flat Washer
Ø8
Qty: 8
2
Spring Washer
Ø8
Qty: 8
5
Bolt
M10x50
Qty: 2
7
Flat Washer
Ø10
Qty: 2
6
Spring Washer
Ø10
Qty: 2
36
22
35
23
3
3
2
4
2
4
5
6
7
STEP 2 HARDWARE :
NOTE: Be careful not to pinch any wires while
assembling handlebars.

12
ASSEMBLY STEP 3
3.1 Insert the Seat Slider Rail (34) through the Seat
Frame (35).
35
34
NOTE: Make sure the seat slider lever is in the
open position when inserting the slider rail.

13
ASSEMBLY STEP 4
4.1 Open Hardware for Step 4.
4.2 Attach assembled Seat Set and Rear Cover
Bracket (27) to the Main Frame (20) using
6 Bolts (8), 6 Spring washers (2), and 6 Flat
Washers (3). Tighten firmly.
20
27
NOTE: Be careful not to pinch any wires while
assembling seat.
3
Flat Washer
Ø8
Qty: 6
2
Spring Washer
Ø8
Qty: 6
8
Bolt
M8x15
Qty: 6
STEP 4 HARDWARE :
3
2
8

14
ASSEMBLY STEP 5
5.1 Connect Handlebar Cable (29) to Seat Cable
(28).
5.2 Attach the Seat Slider Cover (24) to the Rear
cover bracket (27) using 1 Bolt (11).
28
29
27
24
11
NOTE: Be careful not to pinch any wires while
assembling cover.
STEP 5 HARDWARE :
11
Bolt
M4x15
Qty: 1

15
ASSEMBLY STEP 6
6.1 Open hardware for Step 6.
6.2 Wrap Lead Wire (24) around the Console Cable
(25) and Heart Rate Cables (27). Pull the wires
through the Mast Cover (26) and the Console
Mast (33) hole.
6.3 With the Mast Cover (26) on the Console
Mast (33), attach the Console Mast (33) to the
Main Frame (20) using 6 Bolts (8,9), 6 Spring
Washers (2), and 6 Flat Washers (3). Tighten
firmly.
6.4 Slide Mast Cover (26) down onto Main Frame
(20) and snap into place.
33
24
25
27
26
20
8
2
3
29
3
NOTE: Be careful not to pinch any wires while
assembling handlebars.
STEP 6 HARDWARE :
3
Flat Washer
Ø8
Qty: 6
2
Spring Washer
Ø8
Qty: 6
9
Bolt
M8x65
Qty: 4
8
Bolt
M8x15
Qty: 2

16
ASSEMBLY STEP 7
7.1 Open hardware for Step 7.
7.2 Connect Console Cable (25), Heart Rate Cables
(27), and Fan Cable (28) to Console (32). Tuck
any wire slack into cutout on Console Mast (33).
7.3 Attach Console (32) to Console Mast (33) using
4 Bolts (10). Tighten firmly.
33
27
10
10
Bolt
M5x10
Qty: 4
STEP 7 HARDWARE :
32
25
28
NOTE: Be careful not to pinch any wires while
assembling console.

17
ASSEMBLY STEP 8
37R
38R
37L
39L
39R
38L
8.1 Identify Left Pedal (37L) which is labeled Lon
spindle and Right Pedal (37R) labeled R.
8.2 Insert Left Pedal Strap (39L) into Left Pedal
(37L) and Right Pedal Strap (39R) into Right
Pedal (37R).
8.3 Insert Left Pedal (37L) into Left Crank Arm
(38L), ensure screw threads are aligned. Tighten
Counter-clockwise.
8.4 Insert Right Pedal (37R) into Right Crank Arm
(38R), ensure screw threads are aligned. Tighten
Clockwise.
8.5 Use Wrench to fully tighten pedals. No screw
threads should be visible and pedal axle should
be fully seated.
NOTE: Make sure pedals are FULLY TIGHTENED
before use.
NOTE: Left crank arm is reverse threaded so it
is very important to tighten counter-clockwise.
Tightening the opposite direction can damage
pedal or crank arm.

18
ASSEMBLY STEP 9
CONGRATULATIONS!
You have successfully assembled your Recumbent
Bike.

19
CONSOLE OPERATION

20
5.0R
SPLIT
0 20 40 60 80 100
ENTER
DISPLAY
RESISTANCE
TIMECADENCE RESISTANCE
STOP
STA RT
PROGRAMS
MANUAL
P1 CALORIES P5
DISTANCE P4 INTERVALS
P3 FAT BURN P2
5.0R CONSOLE
Up/Down Keys
Program Indicators
Quick Keys
USB Port (Backside)
LCD Display
Bluetooth Button
Fan Speed Button
NOTE: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use.