Hubbell KILLARK VEB Series Instruction Manual

Page 1 of 4
3940 Dr. Martin Luther King Drive
St. Louis, MO 63113
P/N 00912293 FORM NO. K1207 Released 05/01
INSTALLATION, OPERATION &
MAINTENANCE DATA SHEET
(VEB/DEB/VEQ SERIES FLUORESCENT
EMERGENCY LIGHTING FIXTURES)
VEB/DEB/VEQ SERIES FLUORESCENT
EMERGENCY LIGHTING FIXTURES
CAUTION:
Before installing, make sure you are compliant with area classications, failure to do so may result in bodily injury,
death and property damage. Do not attempt installation until you are familiar with the following procedures. All
installation must comply with the applicable Electrical Code.
Make sure that the circuit is de-energized before starting installation or maintenance.
Verify that the installation is grounded. Failure to ground will create electrical shock hazards, which can cause
serious injury and or death.
Technical information, advice and recommendations contained in these documents is based upon information
that Killark believes to be reliable. All the information and advice contained in these documents is intended for
use only by persons having been trained and possessing the requisite skill and know-how and to be used by
such persons only at their own discretion and risk. The nature of these instructions is informative only and does
not cover all of the details, variations or combinations in which this equipment may be used, its storage, delivery,
installation, check out, safe operation and maintenance. Since conditions of use of the product are outside of the
care, custody and control of Killark, the purchaser should determine the suitability of the product for his intended
use, and assumes all risk and liability whatsoever in connection therewith.

Page 2 of 4
3940 Dr. Martin Luther King Drive
St. Louis, MO 63113
P/N 00912293 FORM NO. K1207 Released 05/01
1. IMPORTANT SAFEGUARDS -
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
NOTE: Read this sheet carefully before beginning
installation.
• Do not use this equipment for other than
the intend use as specied on equipment
nameplate. Turn off the supplying circuit before
beginning installation, or performing any
maintenance including revamping.
• Do not install near gas or electric heaters.
• Do not attempt to service battery. The
emergency ballast contains a sealed, no-
maintenance battery. Contact manufacturer for
information on replacements.
• Batteries must be recycled or disposed of
properly.
• Servicing should be performed by qualied
service personnel.
• Do not use this equipment for other than
intended use.
• The use of accessory equipment not
recommended by the manufacturer man cause
an unsafe condition.
• Equipment should be mounted in locations and
at heights were it will not readily be subjected
to tampering by unauthorized personnel.
• The emergency ballast is for use with bi or
quad pin uorescent lamps only.
2. INSTALLATION
CAUTION: To prevent high voltage on red
& yellow output leads prior to installation,
inverter connector must be open. Join inverter
connector after installation, then turn power
ON.
To reduce the risk of electrical shock,
disconnect the AC input and inverter before
servicing.
The emergency ballast must be connected to
an unswitched power source (120/277 V).
NOTE: All installations must comply with the
applicable local and/or National Electrical
Code.
IMPORTANT: Before installing, check the
xture nameplate to be sure you have the
correct xture. Verify ground continuity in the
electrical system.
Refer to nameplate for specic ambient and
supply wire temperature rating.

Page 3 of 4
3940 Dr. Martin Luther King Drive
St. Louis, MO 63113
P/N 00912293 FORM NO. K1207 Released 05/01
1. Install splice box per Instruction Sheet K0451
supplied with the product.
2. Refer to Fig.1 for general guidance. Hang the
xture on the splice box hinge.
3. Attach the green (ground) lead to the splice
box ground screw (provided).
4. For VEB/DEB Series connect the supply
common lead to marked “COM” & supply
line voltage hot lead (120 or 277) to marked
“LINE” at the terminal block. For VEQ series
connect the supply common lead to marked
“COM” & supply line voltage hot lead to
marked “LINE” at the terminal block.
5. Mount the lamps on socket supplied with the
xture.
6. Join the emergency ballast(s) inverter
connector(s) as shown in Fig.2.
7. Close the ballast tank against the splice box
and tighten the screw to secure it.
8. Install globe or refractor in the globe thread.
Hand tighten.
9. Install globe guard (if required) over lugs on
ballast tank, turn until stopped. Secure with
screw.
10. To install reectors, back out (4) screws
provided in ballast tank boxes enough to
slip the reector over the screws and twist in
place. Tighten screws to secure reector.
11. Turn ON the supply circuit to operate the
xture.
NOTE: For push to test station installation
use Killark control station catalog number
FXCS_5B2 (e/push to test nameplate) or
equivalent. Refer to Fig.3 for typical wiring
diagram.
FIG.2
FIG.3

3940 Dr. Martin Luther King Drive
St. Louis, MO 63113
P/N 00912293 FORM NO. K1207 Released 05/01 Page 4 of 4
2. OPERATION:
When AC power is applied, the charging
indicator light is illuminated, indicating that the
batter is being charged. When power fails, the
emergency ballast automatically provides at
least 90 minutes of emergency lighting.
3. MAINTENANCE:
As routine maintenance, this emergency
xture should be checked periodically to
ensure proper operation, The following
schedule is recommended.
1. Visually inspect the charging indicator light
monthly. It must be illuminated.
2. Test operation of the circuit at 30 day intervals
for a minimum of 30 seconds. The lamp
should operate.
3. Conduct a 90 minute discharge test once a
year. The lamp should operate for 90 minutes.
SAVE THESE INSTRUCTION SHEETS