Hubbell WPH Series User manual

HubbellCanadaLP,LightingDivision
870BrockRoadSouth,Pickering,ON,L1W1Z8
Tel.(905)8391138
Formoreinformation,visitourwebsite: www.hubbellonline.com
INSTALLATIONINSTRUCTIONS
HighPressureSodium&Metal
HalideWallPack
WGH/WPH/WGCSeries
WARNING
DISCONNECTPOWERDURINGINSTALLATIONANDBEFORESERVICING.
READALLINSTRUCTIONSCOMPLETELYBEFORESTARTINGINSTALLATION
SAFETYPRECAUTIONS
Beforestartingtheinstallation,disconnectthepowerbyturningoffthe
circuitbreaker.Turningthepoweroffbyusingthelightswitchisnot
sufficienttopreventelectricalshock.
Readallwarningsandinformationoncarton(s)andproduct(s).
Thisfixtureisintendedforwallmountinstallationovera4junctionbox.
ThisfixturemustbewiredinaccordancewiththecurrentnationalElectricCode
andapplicablelocalcodesandordinances.Propergroundingisrequiredto
ensurepersonalsafe.
Aqualifiedelectricianmustperformallwiring.Failuretoreadandfollow
theseinstructionscouldresultinseriousinjuryordeath.
MOUNTING
BoxMounting:
1.Placesupplywiresthroughprovidedmountingplatewithgasketandattachto
junctionbox.
2.Removerefractor,andthenremovereflectorplatefromthefixture.
3.Removecloseupplugatthebottom.
4.Feedsupplyleadstothefixtureandinstallthenut.
5.Connectfixtureleadstosupplyleadswithwirenuts.
6.Replacereflectorplateandinstalllamp.Reinstallrefractor.
ConduitMounting:
1.Removerefractorandthereflectorplatefromthefixture
2.Removecloseuppluginhousingfordesiredconduitentrance.
3.Connectfixtureleadstosupplyleadswithwirenuts.
4.Replacereflectorplateandinstalllamp.Reinstallrefractor.
INSTALLATIONINSTRUCTIONS
HighPressureSodium&Metal
HalideWallPack
WGH/WPH/WGCSeries

HubbellCanadaLP,LightingDivision
870BrockRoadSouth,Pickering,ON,L1W1Z8
Tel.(905)8391138
Formoreinformation,visitourwebsite: www.hubbellonline.com
WARNING
DISCONNECTPOWERDURINGINSTALLATIONANDBEFORESERVICING.
READALLINSTRUCTIONSCOMPLETELYBEFORESTARTINGINSTALLATION
GROUNDING
Insurethatthefixtureismountedsecurelyforpropergrounding.Useapproved
connectorforallelectricalconnections.
MAINTENANCE
Thefixtureisdesignedforyearsoftroubletreeoperation.Foroptimum
performance,cleanthereflectorandrefractorperiodicallywithanonabrasive
cleaner.
TROUBLESHOOTING
Intheeventthatthefixturefailstooperateproperly,checkthefollowing:
Theproperlampisproperlyinstalled.
Thelampisnotbrokenorfaulty
Thelinevoltageatthefixtureiscorrect.
Thefixtureiswiredproperly
Thefixtureisgroundedproperly.
Thephotocell(optional,byothers)ifinstalled,
isofpropervoltageandrating.
(seetypicalwiringdiagram)
Thereisnoreflectedlightbackintothephotocell
causingthefixturetoturnoffifphotocellinstalled.
WARNING!Replaceonlywithalampofsametypeandwattageasindicatedonthe
fixturelabel.