Hubbell SAVVANO User manual

SAVVANO™
LED Decorative Highbay
WARNINGS
• This product contains chemicals known to the state of California to cause cancer,
birth defects and/or other reproductive harm.
• Thoroughly wash hands after installing, handling, cleaning, or otherwise touching
this product.
• Contact Hubbell Lighting, Inc. for information and direction before relamping or
replacing this light xture.
• Disconnect power before installing or servicing.
• Install, operate and maintain to meet all applicable codes.
• Protect all wiring connections with approved insulators (by others.)
• Selected xture voltage must match supply line voltage.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Upon receipt of this xture, thoroughly inspect it for any damage. If any is
found, the carrier should be notied and held accountable.

INSTALLATION INSTRUCTIONS
FIXTURE RECEIVING:
• For shipping purposes, the fixture will come in multiple boxes.
• The upper assembly will be packaged separately from the reflector assembly and, if optioned, the lens assembly.
• See instructions on pages 3 & 4 for initial fixture assembly.
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 2 Phone [phone]
Industrial Lighting
®
SAV–SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
OPTIONAL
EQUIPMENT
FIGURE 1
FIXURE BOXING
UPPER
ASSEMBLY
REFLECTOR
ASSEMBLY
LENS RING/
HARDWARE
LENS
FIXTURE RECEIVING:
•For shipping purposes, the fixture will come in multiple boxes.
•The upper assembly will be packaged separately from the reflector
assembly and, if optioned, the lens assembly.
•See instructions on pages 3 & 4 for initial fixture assembly.
REFLECTOR INSTALLATION:
MH / MM / ML MODELS (See Figure 2B)
1. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground,
it is best to place fixture upside down.
2. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them
with the holes in the reflector collar.
3. Insert the studs through the holes and thread on the provided hexagonal nut. Using a 5/16”
hex driver, tighten hexagonal nut to 10 in-lbs.
4. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground,
it is best of place fixture upside down.
5. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them
with the holes in the reflector collar.
6. Insert the studs through the holes and install the provided hexagonal standoffs along with
lock washers. Using a 1/4” hex driver, tighten the whexagonal standoffs to 10 in-lbs.
LX/ LH MODELS (See Figure 2A)

INSTALLATION INSTRUCTIONS
REFLECTOR
COLLAR ASSEMBLY
REFLECTOR
COLLAR ASSEMBLY
FIGURE 2B
REFLECTOR COLLAR MOUNTING
MH / MM / ML
FIGURE 2A
REFLECTOR COLLAR MOUNTING
LX / LH
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 3 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
HEXAGONAL
STANDOFF
4 PLACES
LOCK
WASHER
4 PLACES
THREADED
STUD
4 PLACES
HEXAGONAL
NUT
4 PLACES
THREADED
STUD
4 PLACES
REFLECTOR INSTALLATION:
MH / MM / ML MODELS (See Figure 2B)
1. Reflector can be installed on the ground or while fixture is hanging. If
installing on the ground, it is best to place fixture upside down.
2. Locate the four (4) threaded studs protruding from the bottom of the
glass lens ring and align them with the holes in the reflector collar.
3. Insert the studs through the holes and thread on the provided hexagonal
nut. Using a 5/16" hex driver, tighten hexagonal nut to 10 in-lbs.
LX/ LH MODELS (See Figure 2A)
4. Reflector can be installed on the ground or while fixture is hanging. If
installing on the ground, it is best of place fixture upside down.
5. Locate the four (4) threaded studs protruding from the bottom of the
glass lens ring and align them with the holes in the reflector collar.
6. Insert the studs through the holes and install the provided hexagonal
standoffs along with lock washers. Using a 1/4" hex driver, tighten the
hexagonal standoffs to 10 in-lbs.

LENS INSTALLATION (If Optioned):
1. Once the reflector has been mounted to the upper assembly, then the lens can be installed.
2. Seat the lens into the bottom of the reflector.
3. Orient Lens Mounting Ring such that short leg of the cross section is on top and install over the lip of the reflector
and lens. See Figure 3B.
4. While manually holding the ring together, install screw through bracket holes and thread on hexagonal nut and
tighten till snug.
INSTALLATION INSTRUCTIONS
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 4 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
LENS
(OPTIONAL)
REFLECTOR
LENS
MOUNTING RING
(OPTIONAL)
HEXAGONAL
NUT
SCREW
LENS MOUNTING RING
SEE NOTE 3
LENS
REFLECTOR
FIGURE 3A
LENS MOUNTING
FIGURE 3B
LENS INSTALLATION (If Optioned):
1. Once the reflector has been mounted to the upper assembly,
then the lens can be installed.
2. Seat the lens into the bottom of the reflector
3. Orient Lens Mounting Ring such that short leg of the cross
section is on top and install over the lip of the reflector and
lens. See Figure 3B.
4. While manually holding the ring together, install screw through
bracket holes and thread on hexagonal nut and tighten till snug.
GENERAL INFORMATION
• All 12” (304.8 mm) minimum supply wire outside of conduit.
• Fixture mounting hub conduit threads are 3/4-14 NPS.
PENDANT MOUNTING: (See Figures 4A & 4B)
1. Remove the Wire Access Cover and Mounting Hub Assembly from the fixture top by removing the (3) ¼” screws using a
3/8” Hex driver or flathead screwdriver. See Figure 4B.
2. The Mounting Hub Assembly should be installed on the already-hanging pendant conduit. See Figure 4A. The conduit and
conduit lock nut should be securely fastened into the Mounting Hub at this time.
3. Thread the Set Screw into the Mounting Hub to lock into the Conduit using a 1/8” Allenhead driver. See Figure 4A.
4. Loosely thread the Hub Lock Nut onto the Mounting Hub so that there is play between the Hub Plate and Mounting Hub.
See Figure 4A.
5. Feed electrical supply wire through the conduit and out the bottom of the Mounting Hub, with 12” of extra wire
protruding from the bottom.
6. Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate.
Align holes in the Hub Plate with the holes in the Top Plate and insert and tighten the (2) ¼” screws to secure the position
of the Hub. Tighten the Hub Lock Nut to the lock the plate and hub in place.

INSTALLATION INSTRUCTIONS
7. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole and make the wiring connections.
See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure
incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress
wires as needed.
8. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with
(1) ¼” screw.
FIGURE 4A
PENDANT-MOUNTING HUB
ASSEMBLY
HUB LOCK NUT
HUB PLATE
MOUNTING
HUB
NOTE: SET SCREW TO BE
THREADED BELOW OUTER
THREADS OF HUB FOR LOCK
NUT TO BE ABLE TO THREAD
SCREW
2x 1/4-20X.50
SCREW
1/4-20X.50
MOUNTING HUB
ASSEMBLY
3/8" BUSHING
WIRE ACCESS COVER
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 5 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
CONDUIT FOR
PENDENT HANGING
CONDUIT
LOCK NUT
FIGURE 4B
PENDENT MOUNT
ASSEMBLY
FIXTURE
TOP PLATE
GENERAL INFORMATION
•All 12” (304.8 mm) minimum supply wire outside of c
onduit.
•Fixture mounting hub conduit threads are 3/4-14 NPS
.
PENDANT MOUNTING: (See Figures 4A & 4B)
1. Remove the Wire Access Cover and Mounting Hub Assem
bly from
the fixture top by removing the (3) 1/4" screws usi
ng a 3/8" Hex driver or
flathead screwdriver. See Figure 4B.
2. The Mounting Hub Assembly should be installed on th
e already-hanging
pendant conduit. See Figure 4A. The conduit and co
nduit lock nut should
be securely fastened into the Mounting Hub at this
time.
3. Thread the Set Screw into the Mounting Hub to lock
into the Conduit
using a 1/8" Allenhead driver. See Figure 4A.
4. Loosely thread the Hub Lock Nut onto the Mounting H
ub so that there is
play between the Hub Plate and Mounting Hub. See Fi
gure 4A
5. Feed electrical supply wire through the conduit and
out the bottom of
the Mounting Hub, with 12" of extra wire protruding
from the bottom.
6. Hang fixture so that the Mounting Hub sets into the
Top Plate and the
hub flanges engage the inside of the top plate. Ali
gn holes in the Hub
Plate with the holes in the Top Plate and insert an
d tighten the (2) 1/4"
screws to secure the position of the Hub. Tighten t
he Hub Lock Nut to the
lock the plate and hub in place.
7. Pull the excess fixture and incoming wiring out thr
ough the Wire Access
Cover hole and make the wiring connections. See app
ropriate WIRING
SCHEMATIC for reference. Incoming power to be conn
ected to the white
and black wires. Ensure incoming wiring ground wire
connected to fixture
ground connector. See warnings above about wire con
nections. Dress
wires as needed.
8. Once all wiring connections are made, place all wir
ing back inside wire
box under the Access Cover and replace cover with (
1) 1/4" screw.

GENERAL INFORMATION
• All 12” (304.8 mm) minimum supply wire outside of conduit.
• Fixture mounting hub conduit threads are 3/4-14 NPS.
PENDANT MOUNTING: (See Figures 4A & 4B)
1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum of 90 degC 16/3 SOW-A.
2. Remove Wire Access Cover after removing ¼” retaining screw.
3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) ¼” Screws.
4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub. Place Cord Grip (C) with cone shape up
on top of washer (G).
5. Thread Hook Lock Nut (D) to within 1/8” of the top of the hook threads.
6. Insert Cord (B) through cord grip and washers and through the mounting hub.
7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut. Use pliers and wrench to tighten the
Hook Lock Nut (D) to lock the hook in place.
CAUTION: Do not twist the Hook by using a screwdriver blade - too much force could break the Hook.
8. Using a 1/8” Allen head driver, tighten Set Screw in Mounting Hub to secure Hook from loosening.
9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with
holes in Top Plate and insert and tighten ¼” screws to secure position of Hub. Tighten the Hub Locknut to lock Plate and
Hub in place.
10. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole and make the wiring connections.
See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure
incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress
wires as needed.
11. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with
(1) ¼” screw.
12. Attach Hook Closure Bracket onto end of Hook with screw provided. After fixture is hung, the Closure Bracket should be
secured across the Hook opening to prevent disengagement.
INSTALLATION INSTRUCTIONS
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 6 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
FIGURE 5A
HOOK LOOP ASSEMBLY
FIGURE 5C
HOOK LOOP ASSEMBLY
SCREW
1/4-20X.50
WIRE ACCESS COVER
3/8" BUSHING
SCREW
2x 1/4-20X.50
FIXTURE
TOP PLATE
HUB LOCK NUT
NOTE: SET SCREW TO BE
THREADED BELOW OUTER
THREADS OF HUB FOR LOCK
NUT TO BE ABLE TO THREAD
MOUNTING
HUB
HUB PLATE
A
D
HOOK
CLOSURE
BRACKET/SCREW
G
E
G
C
FIGURE 5B
MOUNTING HUB
ASSEMBLY
B
GENERAL INFORMATION:
•All 12” (304.8 mm) minimum supply wire outside of conduit.
•Fixture mounting hub conduit threads are 3/4-14 NPS.
HOOK/LOOP MOUNTING: (See Figures 5A, 5B & 5C)
1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum
of 90 degC 16/3 SOW-A.
2. Remove Wire Access Cover after removing 1/4" retaining screw
3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) 1/4" Screws.
4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub.
Place Cord Grip (C) with cone shape up on top of washer (G).
5. Thread Hook Lock Nut (D) to within 1/8" of the top of the hook threads.
6. Insert Cord (B) through cord grip and washers and through the mounting hub.
7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut.
Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place.
CAUTION: Do not twist the Hook by using a screwdriver blade - too much force
could break the Hook.
8. Using a 1/8” Allenhead driver, tighten Set Screw in Mounting Hub to secure Hook
from loosening.
9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the
plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4"
screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in
place.
10. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole
and make the wiring connections. See appropriate WIRING SCHEMATIC for
reference. Incoming power to be connected to the white and black wires. Ensure
incoming wiring ground wire connected to fixture ground connector. See warnings
above about wire connections. Dress wires as needed.
11. Once all wiring connections are made, place all wiring back inside wire box under
the Access Cover and replace cover with (1) 1/4" screw.
12. Attach Hook Closure Bracket onto end of Hook with screw provided. After fixture is
hung, the Closure Bracket should be secured across the Hook opening to prevent
disengagement.
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 6 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
FIGURE 5A
HOOK LOOP ASSEMBLY
FIGURE 5C
HOOK LOOP ASSEMBLY
SCREW
1/4-20X.50
WIRE ACCESS COVER
3/8" BUSHING
SCREW
2x 1/4-20X.50
FIXTURE
TOP PLATE
HUB LOCK NUT
NOTE: SET SCREW TO BE
THREADED BELOW OUTER
THREADS OF HUB FOR LOCK
NUT TO BE ABLE TO THREAD
MOUNTING
HUB
HUB PLATE
A
D
HOOK
CLOSURE
BRACKET/SCREW
G
E
G
C
FIGURE 5B
MOUNTING HUB
ASSEMBLY
B
GENERAL INFORMATION:
•All 12” (304.8 mm) minimum supply wire outside of conduit.
•Fixture mounting hub conduit threads are 3/4-14 NPS.
HOOK/LOOP MOUNTING: (See Figures 5A, 5B & 5C)
1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum
of 90 degC 16/3 SOW-A.
2. Remove Wire Access Cover after removing 1/4" retaining screw
3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) 1/4" Screws.
4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub.
Place Cord Grip (C) with cone shape up on top of washer (G).
5. Thread Hook Lock Nut (D) to within 1/8" of the top of the hook threads.
6. Insert Cord (B) through cord grip and washers and through the mounting hub.
7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut.
Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place.
CAUTION: Do not twist the Hook by using a screwdriver blade - too much force
could break the Hook.
8. Using a 1/8” Allenhead driver, tighten Set Screw in Mounting Hub to secure Hook
from loosening.
9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the
plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4"
screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in
place.
10. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole
and make the wiring connections. See appropriate WIRING SCHEMATIC for
reference. Incoming power to be connected to the white and black wires. Ensure
incoming wiring ground wire connected to fixture ground connector. See warnings
above about wire connections. Dress wires as needed.
11. Once all wiring connections are made, place all wiring back inside wire box under
the Access Cover and replace cover with (1) 1/4" screw.
12. Attach Hook Closure Bracket onto end of Hook with screw provided. After fixture is
hung, the Closure Bracket should be secured across the Hook opening to prevent
disengagement.

INSTALLATION INSTRUCTIONS
WIRE GUARD INSTALLATION (If Optioned):
1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector.
2. The guard should mount around the lens ring such that the ring fits between the top two circular rings.
3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the
guard is clamped around the lens ring.
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 9 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
33.5 26.5
MH / MM / ML MODELS
LX / LHMODELS
WIRE GUARD INSTALLATION (If Optioned):
1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector.
2. The guard should mount around the lens ring such that the ring fits between the top two circular rings.
3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the
guard is clamped around the lens ring.
WIRE GUARD
SCREW (2X)
KEPIS NUT (2X)
FIGURE 6A
WIRE GUARD ASSEMBLY

INSTALLATION INSTRUCTIONS
OCCUPANCY SENSOR INSTALLATION (If Optioned):
NOTE: If a wire guard is supplied, the wire guard needs to be installed first (see Page 9, Fig. 7A) before installing sensor on the
bracket. Position the guard so the sensor bracket fits through the top two rings of the guard.
1. Position the sensor box (without the tightening ring attached) on top of the bracket and place the threaded shaft through
the hole in the bracket. Fasten the tightening ring onto the threads until sensor box is secure. See Fig. 7B.
2. Screw the sensor lens onto the threaded shaft until secure. See Fig. 7C.
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 10 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
Mounting Bracket
FIGURE 7B
SENSOR INSTALLATION
FIGURE 7C
SENSOR INSTALLATION
Mounting Bracket
OCCUPANCY SENSOR INSTALLATION (If Optioned):
NOTE: If a wireguard is supplied, the wire guard needs to be installed first (see Page 9, Fig. 7A) before installing sensor on the
bracket. Position the guard so the sensor bracket fits through the top two rings of the guard.
1. Position the sensor box (without the tightening ring attached) on top of the bracket and place the threaded shaft through
the hole in the bracket. Fasten the tightening ring onto the threads until sensor box is secure. See Fig. 7B
2. Screw the sensor lens onto the threaded shaft until secure. See Fig. 7C.
WIRE GUARD ASSEMBLY
W/ OCCUPANCY SENSOR
FIGURE 7A
WIRE GUARD ASSEMBLY
W/ OCCUPANCY SENSOR

LINE DRAWINGS
Drop (DLR) Lens Conical Drop (CDL) Lens P95/Clear (CLR)/No Lens
Drop (DLR) Lens Conical Drop
(CDL) Lens
P95/Clear (CLR)/
No Lens
31.0”
22.6”
28.4”
30.1”
10.2”
25.0”
16.5”
23.1”
10.2”
21.8”
31.0”
22.6”
28.4”
30.1”
10.2”
25.0”
16.5”
23.1”
10.2”
21.8”
22” Option
16” Option

WIRING DIAGRAMS
HIL_0355_SAV_IN_17 7/17
Hubbell Lighting, Inc. Doc. No. 93082515 A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive • Greenville, SC 29607 Page 11 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
ELECTRICAL DIA
GRAM
LX / LH
MODELS
BLUE
BLACK
WHITE
B
L
A
C
K
WHITE
LEADS
BLACK
LEADS
B
R
O
W
N
BLUE
BLUE
BROWN
OPTION - FUSING
BLACK
WHITE
TERMINAL ATTACHED TO
WIRE BOX (INSIDE)
GREEN
GREEN
BLACK
RED
BLUE
WHITE
BLACK
RED
-W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UP
THROUGHWIRE BOX WITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE
-W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TO
APPROPR
IATE C
O
N
NECT
O
RS
O
N SENS
O
R P
O
W
ERPACK.
DIMMING OPTION
VIOLET LEADS GRAY LEADS
FROM DRIVER #2
FROM DRIVER #1
FROM DRIVER #2
FROM DRIVER #1
SEE TERMINATION OPTIONS
DRIVER #2
DRIVER #1
SURGE
SUPPRESSOR
BLACK
LEADS
WHITE
LEADS
RED
RED
GREEN
G
R
E
E
N
OPTION -
OCCUPANCY SENSOR
POWERPACK
OPTION -
OCCUPANCY SENSOR
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 9 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
BLUE
BLACK
WHITE
B L A C K
WHITE LEADS
BLACK LEADS
B R O W N
BLUE
BLUE
BROWN
OPTION - FUSING
BLACK
WHITE
TERMINAL ATTACHED TO WIRE BOX (INSIDE)
GREEN
GREEN
BLACK
RED
BLUE
WHITE
BLACK
RED
VIOLET AND GRAY LEAD TO BE GROUPED W ITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE WHEN DIMMING OPTION IS UTILIZED
D
I
M
M
I
N
G
O
P
T
I
O
N
VIOLET LEADS GRAY LEADS
FROM DRIVER #2 FROM DRIVER #1
FROM DRIVER #2 FROM DRIVER #1
SEE TERMINATION OPTIONS
DRIVER #2
DRIVER #1
SURGE
SUPPRESSOR
BLACK LEADS
WHITE LEADS
RED
RED
GREEN
G R E E N
ELECTRICAL DIAGRAM
LX / LH MODELS
Hubbell Lighting, Inc. Doc. No. 93082515 A subsidiary of Hubbell Incorporated Revision A 701 Millennium Drive • Greenville, SC 29607 Page 12 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
ELECTRICAL DIA
GRAM
MH / MM /
ML MODELS
BLACK
BLACK
WHITE
B
L
A
C
K
WHITE
LEADS
BLACK
LEADS
BLUE
BROWN
OPTION - FUSING
BLACK
WHITE
TERMINAL ATTACHED TO
WIRE BOX (INSIDE)
GREEN
GREEN
RED
BLUE
WHITE
BLACK
RED
DIMMING OPTION
VIOLET LEADS GRAY LEADS
FROM DRIVER #1
FROM DRIVER #1
DRIVER #1
SURGE
SUPPRESSOR
BLACK
LEADS
WHITE
LEADS
SEE TERMINATION OPTIONS
RED
GREEN
OPTION -
OCCUPANCY SENSOR
POWERPACK
-W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UP
THROUGHWIRE BOX WITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE
-W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TO
APPROPRIATE CONNECTORS ON SENSOR POWERPACK.
Hubbell Lighting, Inc. Doc. No. 93082515
A subsidiary of Hubbell Incorporated Revision A
701 Millennium Drive • Greenville, SC 29607 Page 10 Phone [phone]
Industrial Lighting
®
SAV-SAVVANO DECORATIVE FIXTURE
INSTALLATION INSTRUCTIONS
BLACK
BLACK
WHITE
B L A C K
WHITE LEADS
BLACK LEADS
BLUE
BROWN
OPTION - FUSING
BLACK
WHITE
TERMINAL ATTACHED TO WIRE BOX (INSIDE)
GREEN
GREEN
RED
BLUE
WHITE
BLACK
RED
VIOLET AND GRAY LEAD TO BE GROUPED W ITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE WHEN DIMMING OPTION IS UTILIZED
D
I
M
M
I
N
G
O
P
T
I
O
N
VIOLET LEADS GRAY LEADS
FROM DRIVER #1
FROM DRIVER #1
DRIVER #1
SURGE
SUPPRESSOR
BLACK LEADS
WHITE LEADS
SEE TERMINATION OPTIONS
RED
GREEN
ELECTRICAL DIAGRAM
MH / MM / ML MODELS