HUROM H-AA Series User manual

02
04
06
07
08
13
14
15
17
18
20
24
Precautions for Safe Use
Terms of Parts
How to Disassemble : Chamber
How to Prepare Ingredients / Use by Strainer Types
How to Assemble
Cautions during Operation
How to Use
How to Use Control Lever (by mode/by ingredients)
When Squeezing Screw Stops during Operation
/ Caution when Using Operation Button
How to Clean
Before Requesting Repair
Product Specifications / Warranty
CONTENTS
(Household use only / Warranty Included)
1 Read ‘Precauons for safe use’ (Page 2) and use the appliance properly.
2 Aer nish reading the manual, keep it in a convenient locaon for future reference.
3 Do not use it abroad which has dierent power supply and voltage.
4 Any quality improvements are subject to change without noce.
H-AA Series
TM

0302
PRECAUTIONS FOR SAFE USE
1. You should read <Precautions for safe use>.
2. You should follow <Precautions for safe use>.
3. Precautions are classified as following.
Warning When violating the labeling requirement, it may cause serious injury or death.
Caution When violating the labeling requirement, it may cause serious injury or damage to the appliance.
DO NOT OPERATE WITHOUT LOCKING THE HOPPER PROPERLY. It may cause an injury or a failure.
WHEN A GAS LEAK IS DETECTED, DO NOT INSERT THE POWER CORD INTO ITS SLOT.
OPEN THE WINDOW IMMEDIATELY FOR AIR VENTILATION.
It may cause injury or failure.
NEVER PUT A FINGER, FORK OR SPOON, ETC. INTO JUICE OUTLET. It may cause injury or failure.
IF SQUEEZING SCREW ROTATION IS STOPPED DURING NORMAL OPERATION, PRESS
[REV] BUTTON AND HOLD FOR 3~5 SECONDS AND AFTER REVERSE OPERATION IS
COMPLETELY STOPPED, PRESS [ON] BUTTON AGAIN. If stopping continues during the operation, the
parts may be damaged and performance may be deteriorated due to overheating in a motor. When the problem continues,
stop the appliance immediately and contact the local Customer Service Center.
DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE, DISASSEMBLE THE
CHAMBER SET OR PARTS AND TRY TO LOCK THEM.
It may cause an injury or a failure. If any act of event
needed, switch off first and unplug the power cord.
WHEN USING THE APPLIANCE, BE CAREFUL WITH A NECKTIE, LONG NECKLACE, SCARF,
ETC. TO NOT BE ENTANGLED INTO HOPPER CHUTE.
It may cause injury, failure or breakage.
PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE. It may cause injury or failure.
DO NOT OPERATE THE APPLIANCE FOR MORE THAN 30 MINUTES AT A TIME.
It may cause a motor failure due to overheating. Cool it down sufficiently about 5 minutes and operate it again.
WHEN PLACING INGREDIENTS INTO THE HOPPER CHUTE, USE ONLY THE PUSHER
PROVIDED.
It may cause injury or failure.
DO NOT ALLOW A SEVERE SHOCK TO THE APPLIANCE OR DROP IT. It may cause electric shock,
fire or damage.
IF THE APPLIANCE GIVES OFF AN UNPLEASANT SMELL, EXCESSIVE HEATING, OR
SMOKE, STOP USING IMMEDIATELY AND CONTACT THE LOCAL CUSTOMER SERVICE
CENTER. When using a new appliance, it gives off a smell and the smell disappears naturally over time.
ALWAYS UNPLUG THE APPLIANCE AFTER USE. ALWAYS DISCONNECT THE
APPLIANCE FROM THE SUPPLY IF IT IS LEFT UNATTENDED AND BEFORE ASSEMBLING,
DISASSEMBLING OR CLEANING. WHEN UNPLUGGING THE POWER CORD, MAKE SURE TO
HOLD THE POWER CORD.
Pulling the wire to unplug may cause electric shock or fire.
DO NOT WASH AT HIGH TEMPERATURES OF 800C(1760F) OR HIGHER. DO NOT PUT THE
APPLIANCE IN A DISHWASHER, DRYER OR A MICROWAVE ETC. It may cause a failure or parts
deformation.
THE APPLIANCE WEIGHS ABOUT 4.8kg. WHEN MOVING THE APPLIANCE, ENSURE TO
MOVE IT HOLDING GRIPS TIGHTLY AT THE BOTTOM OF BODY WITH BOTH HANDS. By
attempting to hold chamber or the edge of the body, the body may fall causing an injury or failure.
DO NOT PLUG OR UNPLUG WITH WET HANDS. It may cause electric shock or injury.
DO NOT USE OTHER THAN 230 - 240V AC. It may cause electric shock, fire or product failure.
If the voltage is different, it may shorten the life of the motor or cause a failure.
PLUG THE POWER CORD CORRECTLY AND PUSH IT TIGHT IN A WALL SOCKET.
It may cause an electric shock or a fire.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE MANUFACTURER OF
ITS SERVICE OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD.
If the power cord is damaged, it may cause electric shock or fire.
NEVER ALTER THE APPLIANCE. ALSO, DO NOT DISASSEMBLE OR REPAIR THE PRODUCT
BY YOURSELF. DO NOT INSERT FINGERS, FOREIGN SUBSTANCES OR OBJECTS SUCH AS
PINS INTO GAPS OR HOLES IN THE BODY. It may cause a fire, electric shock or product failure. For any
technical support, contact the authorized local Customer Service Center.
WHEN THE POWER CORD, WIRE IS BROKEN OR DAMAGED, OR THE PLUG-IN PART
BECOME LOOSE, DO NOT OPERATE IT.
It may cause electric shock, fire or injury.
DO NOT MOISTEN BODY OR SPLASH WATER ON THE BASE.
Be careful not to let any liquids or other substances get into the switch of the appliance.
DO NOT OPERATE THE SWITCH WITH WET HANDS. It may cause an electric shock or fire.
FOR SAFETY, MUST DO GROUNDING CONNECTION. ALSO, DO NOT DO THE GROUNDING
ON GAS PIPE, PLASTIC WATER PIPE, TELEPHONE WIRE, ETC.
It could cause electric shock, fire, malfunction or explosion. Be sure to use the electrical outlet with ground connection.
NEVER DISASSEMBLE THE CHAMBER SET DURING OPERATION OR INSERT FINGERS,
FOREIGN OBJECTS SUCH AS FORKS, SPOONS, ETC. INTO HOPPER CHUTE OR JUICE
OUTLET. It may cause injury, accident or product failure.
APPLIANCES CAN BE USED BY PERSONS WITH REDUCED PHYSICAL, SENSORY OR
MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN
GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE
WAY AND IF THEY UNDERSTAND THE HAZARDS INVOLVED. CHILDREN SHALL NOT PLAY
WITH THE APPLIANCE. CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY
CHILDREN. THIS APPLIANCE SHALL NOT BE USED BY CHILDREN. KEEP THE APPLIANCE
AND ITS CORD AWAY FROM CHILDREN.

0504
Pulp Outlet
Shaft
Control Lever
Juice Cap
Juice Outlet
Chamber Packing
Body bump
Juice Cap Packing
Silicone Brush
Brush holder
Safety Sensor ( )
*Chamber Rack can't be separated
after assembling.
Operating switch
Screw axis
Ice Cream
outlet
TERMS FOR PARTS * These components may vary depending on the model.
2 Hopper
1 Pusher
10 Pulp Container
12 Juice Container
11 Juice Container Lid
13 Small Cleaning Brush
14 Cleaning Brush
9 Body
16 Chamber Rack
15 Hopper Lid
3 Squeezing Screw
4 Fine Strainer 5 Coarse Strainer
8 Chamber
6 Ice Cream Strainer
7 Spinning Brush
Pusher hook
Hopper Chute
Safety Sensor ( )
Strainer
bump
How to use
`
* Some parts(Coarse Strainer, Ice Cream Strainer) can be optional for each model.

0706
Turn the hopper counterclockwise and pull it up.
Pull out the squeezing screw holding both sides of wing.
It is for making smoothie, slush and ice cream with frozen fruits.
Do not extract large amount of ingredients at once or put the large chunk of
the ingredients. The juice can be out to pulp outlet or outside of the strainer
when use a little bit defrost fruits. It is natural phenomenon and not a product
failure. Do not use water freezes, ice cube.
Fruits like apple, pear, kiwi, oriental melon, etc. put them with seeds and peels.
However, apple seeds contain toxicity, so it is better to remove them.
Separate each grape from the cluster. Peel the pomegranate and use flesh only.
Peel off the skin of watermelon, orange, grapefruit and cut them into right size.
Fruits like mango, cherry, peach, or plum, etc. have hard seeds which are hard to
swallow. Those seeds might cause stoppage or parts damage, so they must be
removed before using it.
Put a handful of wheat or chives in not to be scattered.
Dice frozen fruits as 2cm to make ice cream. When use the testaceous fruits, please
peel and freeze to use. Fruits with hard seeds such as persimmon, Japanese apricot,
lemon, plum, peach etc. that are hard to chew with our teeth should be taken out
before freeze. Please use seedless grapes.
Cut fibrous ingredients into small sized less than 3cm.
Use by strainer types
* This is a reference about how to trim the ingredients,
so if you have allergy please choose your own proper ingredients.
* Please refer to the recipe book for the product usage of each ingredient.
Please clean all the parts before first use.
Fine strainer has tiny and fine holes for making clean juice.
Apple, pear, kiwi,
oriental melon
Watermelon, orange,
grapefruit
Mango, cherry,
peach
Wheat, chives
Fine
strainer
Coarse
strainer
Flesh
Water parsleys,
angelica, celery, kale
Ice cream
strainer
Pomegranate,
grapes
How to disassemble the chamber How to trim the ingredients
1
2
For juicing
For making Ice Cream
Disassemble the spinning brush and strainer.
4
Disassemble the strainer and spinning brush from the
chamber.
3
This ice cream strainer is only for frozen fruits.
Do not use for crushing ice and grinding.
NOTE
Coarse strainer has larger holes for making thick and pulpy juice.
It is to make juice with soft fruits and thick juice like banana, strawberry, and
also useful for smoothie, latte, or soup.

0908
How to assemble the chamber for juicing
Assemble the strainer and spinning
brush as shown in the picture.
Place the assembled parts from
[STEP 1] into the chamber by
turning the strainer from side
to side to fit the groove in the
bottom bump of the chamber.
Press the squeezing screw into
the assembled parts from
[STEP 2] until the screw fits
perfectly.
Assemble the hopper like
the picture. After putting the
hopper on the chamber, turn
it clockwise until it is locked
completely.
1 2 3 4
bottom
bump of the
strainer
groove of
the chamber

1110
How to assemble the chamber for making ice cream
Ice cream Outlet
Juice outlet
Assemble the chamber and ice cream
strainer.
Place the ice cream outlet align with
juice outlet.
1 2 3
The spinning brush isn't needed
for ice cream making.
NOTE
Assemble the hopper like the
picture. After putting the hopper on
the chamber, turn it clockwise until
it is locked completely.
Press the squeezing screw into
the assembled parts from [STEP 1]
until the screw fits perfectly.

1312
1. The main body itself will not work.
2. The appliance will not work if the chamber
set isn’t assembled well even though it is
on the body.
1
3
Place the control lever of the chamber set
to as image ①.
2
If the control lever is not placed at the
chamber set and body will not fit completely.
Assemble the bottom of the chamber to
bump of the body.
If the sign < ▲> on the body and the sign
< ▼> behind of the chamber set are aligned
well, it is perfectly assembled.
NOTE
How to assemble the chamber set and body
*The assembling method is same regardless of strainer type.
Withered ingredients because of refrigerated for long term may make small amount of juice or
impossible to make juice. If the unit is not cleaned immediately after use, a residue may dry and
stick to the unit. This will make assembling and cleaning difficult as well as lead to performance
degradation.
Ingredients which needs cauon.
It may cause damage or failure.
- Fruits with hard seeds such as persimmon, Japanese apricot, lemon, plum, peach etc. that are hard to




- Do not put in fruits preserved in alcohol, sugar, honey, etc. (grapes, apricot, berries, etc.) and enzymes
(glasswort, house leek, etc.).
We recommend you to drink green vegetable juice and fruit juice immediately aer extracon
rather than keeping them for long me.
Do not use for grinding grains.
- It may cause damage or failure.
Do not re-squeeze residues expelled through the pulp outlet.

Do not operate the appliance before pung in the ingredients.
Do not use the appliance for more than 30 minutes connuously.


Never insert nger, fork or spoon etc. into juice outlet during the operaon.

spinning brush and cause damage to the parts.
Do not press the ingredients with anything except the pusher.

Do not operate the switch with wet hands.

When you extract over 400ml at once, please open the control lever every 400ml to emit the pulp.
- The hopper can’t be opened or it may cause damage when the pressure in the chamber increases.
Please use only ice cream strainer when you put frozen fruits.
Do not put the ice cube, other ingredients and for grinding.
- It may cause damage or failure.
Cautions during Operation
NOTE
③
①②
③

1514
Press [ON] buon to start.
정회전
역회전
정지상태
작동스위치 정회전
역회전
off(정지) 정지
ON
REV
Place the control lever into CLOSE
() position before operating.
Juice : Place the control lever in half-open
( ) pung the last ingredients.
Ice cream : Close( )
the control lever to use.
누름
정회전
역회전
작동스위치 정회전
역회전
ON
REV
The hopper will be opened easily as long as the
residues in the strainer are released.
Stop the machine slowly after press the button for
safety and product performance.
Do not press the ingredients with anything except the
pusher provided.
Please put the ingredients as 3~4cm sizes.
When you use the ice cream strainer, the juice can be
out through outlet and it is normal operation.
When you extract over 400ml at once, please open
the control lever every 400ml to emit the pulp.
For your safety, this appliance only works when
it's correctly assembled with chamber set.
The chamber will not be assembled with body if the
control lever is not into CLOSE( ) position.
How to Use : For juicing / Ice cream
NOTE
1
3
5
2
4
The control lever is between the juice cap and pulp outlet.
The control lever has various functions and can help to extract juice by characteristic of ingredients except extract function.
Cleaning Mode
 ) the control lever to use since the
pulp is not released separately.
Ice cream mode
Preparation/Extraction mode
How to use control lever by mode
NOTE
Completion, Simple Cleaning Mode
Put ingredients gradually in the hopper
chute and press with the pusher.
After extraction is completed, place the
switch in the [REV] position.
When using [ON] or [REV] buon, make sure that the squeezing screw is completely
stopped.
Stop
[On]
On
[Rev]
Reverse
[On]
On
[Rev]
Reverse
Press
Place the control lever into half-closed( ) position
when putting in the last ingredients and release
the residues. The hopper will open easily when the
residues in the strainer are released.

half-closed ( ) position and release the residues.
For general ingredients, the extraction rate is good
when you close ( ) the control lever during
operation. When you extract over 400ml at once,
please open the control lever every 400ml to emit the
pulp.
For juicing the fruits with hard seeds, such as grapes,
rubus coreanus, and pomegranates, place the control
lever into close ( ) and switch into half-
closed( ) position when the juice begins to come out.
When detaching and cleaning the chamber, place the
control lever completely into ( ) position.
You can easily and conveniently clean the chamber.
When it is hard to open the hopper after the operation:
Place the control lever into half-closed ( ) position and press Reverse button for
about 3~4 seconds. Repeat this for 2~3 times and the hopper will be open easily.

1716
Use the control lever by the properties of each ingredients, you can make a more delicious juice.
How to use control lever by ingredients (Juicing)
1
1
2
2
Ingredients
Seed ingredients
Mixed with Milk
NOTE
NOTE
1
2
Apple, pear, melon, watermelon, strawberry, blueberry, orange, grapefruits,
lemon, mango, plum, peach, cherry, persimmon, pineapple, wheat-grass,
parsley, celery, dandelion, carrot, ginger, potato, beet, tomato, paprika, broccoli,
cauliflower, cabbage, kale, spinach, cooked sweet potato and pumpkin, corn.
1. Start as position. 2. When extraction is almost finished, place the
control lever into, Half-Opened position
Grapes, pomegranate, blackberry, kiwi
1. Start as position. 2. When juice starts to come out, place the
control lever into when juice starts to come out.
Banana, strawberry and blueberry, etc.
1. Start as position.
Even aer following the direcons above and sll
doesn’t work, please unplug the power cord and
disassemble chamber set, and clean it. And try it
again.
[REV] is the buon to push back the ingredients
upward.
[REV] only works while pressing the buon, and
the rotaon of the squeezing screw stops if you
release the buon.
Press [REV] buon on the operang switch
for about 3~5 seconds and stop it. Repeat
this 2~3 mes.
Press [ON] buon to operate aer reverse
operaon is completely stopped.
When using [ON] or [REV] buon, make sure that
the squeezing screw stops completely.
Caution when using operation button
In case of reversing during operaon, press [REV] buon shortly to stop the
appliance, then you press [REV] buon for operaon.
From the feature of the product, even though you stop the operaon, it doesn’t stop right away.
It rotates slowly then stops. If the rotaon stops completely, you may press the buon to any
direcon you want.
<ON>
<ON>
<REV>
<REV>
<STOP>
When squeezing screw stops during operation

1918
1.
2.
3.
4.
5.
6.
7.
Unplug the power cord with dry hands after
the unit has been completely stopped.
Remove the chamber set from the main body.
Twist the hopper to open and lift up the parts
in order to disassemble the unit.
Use a cleaning brush and wash the chamber
set under running water.
Open the control lever ( ) and juice
cap to wash the chamber
Wipe the main body with a damp towel or a
soft cloth.
The silicone packing can be disassembled and
washed. (Including juice cap packing, chamber
packing, silicone brush)
Soak in water diluted with one or two drops
of baking soda or natural bleach for dishes for
about 30 minutes to sterilize and clean.
How to Clean
※ When you clean the chamber set, wash the
residue inside of the chamber rst. And then
disassemble the chamber packing and wash it
under running water.
※ When you clean the chamber set, wash the
residue inside of the chamber rst. And then
disassemble the chamber packing and wash it
under running water.
1.
2.
If the chamber is not cleaned immediately aer use, a residue may dry and sck to the
unit. This will make disassembling and cleaning dicult as well as lead to performance
degradaon. Please wash the chamber set immediately aer use.
Do not wash with hot or boiling water, an iron scrubber, abrasive material, sink solvents, or
sharp cleaning tools. Do not put it in a dishwasher or dish dryer. Aer washing, thoroughly
and naturally dry, and store in a clean area.
NOTE
Clean the parts
Remove the silicone brush from the spinning
brush holder.
Use a cleaning brush and wash the inside
and outside of the spinning brush holder
under running water.
Please follow the recommended method to
separate the silicone brush. Otherwise, it may
cause damage of spinning brush holder and
silicone brush.
Wash the silicone brush under running water as
the same method.
1
2
Spinning Brush
Open the juice cap, hold the chamber and juice
cap with one hand, and remove the juice cap
packing with your other hand to disassemble.
Please be careful not to drop or damage the juice
cap and chamber when disassembling the unit.
Pinch the chamber packing with two ngers and
twist to separate.
Please assemble the upper and lower parts
correctly. (Refer to chamber packing image on the
le.)
Juice Cap Packing
Chamber Packing

2120


number or bar code available.
3. The Appliance does not work.
Make sure that the power cord is properly plugged in.
Check if the hopper is assembled properly.
If the hopper has not been locked into place, the appliance will not operate for safety reasons.
Check if the appliance is assembled according to the direcons in the manual.


4. The appliance stops during normal operaon.
Have you inserted heavy loads or large pieces of ingredients into the appliance?
Refer to page 17 of the manual and follow the guideline for using [REV


5. The hopper does not open.
There might be a lot of residues inside. Put the control lever in half-closed ( )
[ONREV

Have you placed any foreign substances or solid objects (hard seed such as persimmon seed) in
the juicer?
Press [

1. The main body itself will not work.
For your safety, this unit only works when it’s
correctly assembled with the chamber set.
2. Please assemble according to the safe-
ty sensor.
For your safety, this unit only works when it's
correctly assembled.
Before Requesting for Repair
8. Juice leaks over the body.
Have you inserted a lot of ingredients into the hopper chute?
If you insert a large amount of ingredients compared to the pulp outlet, the packing is slightly
pushed away, so the juice leaks out of the gap. Do not put too many ingredients by force and just

9. There are ne lines or scratch marks around the squeezing screw.

This is a normal product and there is no problem for use.
10. The Chamber shakes when squeezing.
Slight shaking may be caused by the motor.
Depending on the texture of the ingredient, there may be slight shaking.
-

11. Chamber set does not t into the body.
If the control lever is in position, the chamber set does not fit in to the body. Before
assembling the chamber set, make sure that the control lever is in position.
7. Do not use in ways other than pressing
on the pusher in the inlet.
It may cause damage, injury, etc.
6. Do not insert too many ingredients at
once.
If you insert an excessive amount of ingredi-
ents or thick ingredients, the unit may stop.
ON
REV

2322
Memo Memo

Product name
Supplier Date of purchase
Address
Model name
Manufacturer’s serial number
Customer name
4DC010451_V.02
Product Specifications
Warranty

distributor where you purchased the appliance and keep the original receipt.
 to be

Hurom provides warranty for ten (10) years for the motor and two (2) years for other parts


This warranty does not apply to damages caused by accident, misuse, abuse, commercial
-
vice unauthorized by 
with carrier.

caused by use of this appliance.
-
vice center.

Hurom webpage : www.hurom.com
Product Name
Model Name
Rated Voltage
Rated Frequency
Rated Power
Consumpon
RPM
Hurom Slow Juicer
H-AA Series
230-240 V


43 rpm
Cord Length
Motor
Fuse
Weight
Outward
Dimension
Rated
Operang Hour
1.4 m

motor

4.8 kg
Width 223 mm
Length 180 mm
Height 407 mm
Less than 30 minutes