iArmor EDGE IA-N007 User manual

iArmor®
Customer Support: [email protected]
Rev. 20210801
1
IARMOR EDGE™
PART#: IA-N007
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*DRILLING NOT REQUIRED
*TRIMMING NOT REQUIRED
Torque Value
PART LIST Front
Step Pad Step Pad
Driver Side Step Bar Passenger Side Step Bar
Driver Front Mounting
Bracket (DFM)
Passenger Front Mount-
ing Bracket (PFM)
Driver Rear Mounting
Bracket (DRM) Passenger Rear Mounting
Bracket (PRM)
Driver Front Support
Bracket (DFS)
Passenger Front Support
Bracket (PFS)
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 X
10mm 31-32 √
12mm 56-58 X
14mm 92-94 X

iArmor®
Customer Support: [email protected]
Rev. 20210801
2
M6X1-20mm T-Bolt
X24
M6 Large Flat
Washer
X24
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are not
responsible for any damage caused by the installation.
STEP 1
STEP 2
Starting from the passenger side of the vehicle. Remove the
front body mount bolt, (Fig 1). Do not remove rubber bushings.
M6X1 Nylon
Lock Nut
X24
M10 Flat Washer
X6
M10 Lock Washer
X4
M10X1.5 Hex Nut
X2
M10X1.5-30mm Hex
Bolt
X4
X2
M10 Nut Plate
Install the Step Pads onto the step bars with (16) M6X1-20mm
T-Bolts, (16) M6 Large Flat Washers and (16) M6X1 Nylon
Lock Nuts.
IMPORTANT: Don’t hit the step pad by any metal hummer
within step pad installation, or the step pad will be damaged.
(8) M6X1-20 T-Bolts
(8) M6 Flat Washers
(8) M6 Nylon Lock Nuts
(Fig 1) Passenger Side Front Mounting Location Pictured
Front
Factory Body
Mount Bolt
STEP 3
Attach the Passenger Front Mounting Bracket (PFM) to the
body mount reusing the factory hex bolt, (Fig 2). Do not fully
tighten hardware at this time.
Note: Rotate 90° after inserting the T-Bolts into the
Channel!!!

iArmor®
Customer Support: [email protected]
Rev. 20210801
3
STEP 4
Locate the (2) factory holes at the bottom of the frame beside
the passenger side front body mount, (Fig 3). Insert (1) M10
Nut Plate into the oval hole and line up the threaded nut with
the round hole, (Fig 3).
NOTE: Nut Plate and Support Brackets are not required on 11-
Up 2500/3500 models.
(Fig 3) Passenger Side Front Support Bracket Mounting Location
(Fig 2) Passenger Front Mounting Bracket Installed
Front
Factory Body
Mount Bolt
Insert 10mm
Nut Plate Here
Line Up Nut
Plate Here
M10 Nut Plate
STEP 5
Attach the flat end of the Passenger Front Support Bracket
(PFS) to the installed M10 Nut Plate with (1) M10X1.5-30mm
Hex Bolt, (1) M10 Flat Washer and (1) M10 Lock Washer, (Fig
4 & 5). Do not fully tighten hardware at this time.
Up to 2010 2500/3500 Models:
Note that the Front Support Bracket will not reach up to the
Mounting Bracket, (Fig 5). Tighten the Support Bracket to the
M10 Nut Plate in the frame. Carefully push up on the Support
Bracket until it reaches the inside hole in the Mounting Bracket.
Bolt the Support Bracket to the hole in the Mounting Bracket
with (1) M10X1.5-30mm Hex Bolt, (2) M10 Flat Washers, (1)
M10 Lock Washer and (1) M10X1.5 Hex Nut, (Figs 5 & 6).Do
not fully tighten hardware at this time.
NOTE: Bend Support Bracket up by hand to meet the inner
hole in the Front Mounting Bracket.
Support Bracket not required on 2011-Up 25-3500 Models.
(Fig 4) Passenger Front Support Bracket Installation
Front
(1) M10X1.5-30mm Hex Bolt
(1) M10 Lock Washer
(1) M10 Flat Washer
(1) M10X1.5-30mm Hex Bolt
(1) M10 Lock Washer
(2) M10 Flat Washers
(1) M10X1.5 Hex Nut

iArmor®
Customer Support: [email protected]
Rev. 20210801
4
(Fig 6) Passenger Front Support Bracket Installation
STEP 6
(Fig 5) Passenger Front Support Bracket Installation
Front
(1) M10X1.5-30mm Hex Bolt
(1) M10 Lock Washer
(1) M10 Flat Washers
Front
(1) M10X1.5-30mm Hex Bolt
(1) M10 Lock Washer
(2) M10 Flat Washers
(1) M10X1.5 Hex Nut
Move to the Passenger Side Rear body mount. Repeat Steps 2
–5 to attach the Passenger Rear Mounting Bracket to the body
mount, (Fig 7). Do not fully tighten hardware at this time.
(Fig 7) Passenger Rear Mounting Bracket Installation
Rear
Factory Body
Mount Bolt
STEP 7
Once (2) passenger side brackets are installed, attach the As-
sembled Passenger Side Step Bar onto the Mounting Brackets
with (4) M6X1-20 T-Bolts, (4) M6 Large Flat Washers and (4)
M6x1 Nylon Lock Nuts, (Fig 8). Do not fully tighten hardware.
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
STEP 8
Move to the Driver side of the vehicle. Repeat Steps 2-8 for the
Driver Side Step Bar installation.
STEP 9

iArmor®
Customer Support: [email protected]
Rev. 20210801
5
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use only mild soap/non-abrasive products for cleaning.
(4) M6X1-20 T-Bolts
(4) M6 Large Flat Washers
(4) M6X1 Nylon Lock Nuts
(Fig 8) Passenger Side Step Bar Installed
Front
Warning: Install the T-bolt on the step
bar and rotate it to 90 degrees!!!