iArmor EDGE User manual

iArmor®
Rev. 20210801
1
Customer Support: [email protected]
PART#: IA-N179&N208&N209
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*DRILLING MAYBE REQUIRED
*TRIMMING NOT REQUIRED
IARMOR EDGE™
Passenger Side Step Bar
Step Pad Step Pad
Driver Side Step Bar
PART LIST
Passenger Front Mounting
Bracket (PFM/PCM/PRM)
Driver Front Mounting
Bracket (DFM/DCM/DRM)
Passenger Center Mounting
Bracket (PFM/PCM/PRM)
Passenger Front Support
Bracket (PFS/PCS/PRS)
Driver Front Support
Bracket (DFS/DCS/DRS)
Passenger Center Support
Bracket (PFS/PCS/PRS)
Driver Center Support
Bracket (DFS/DCS/DRS)
Passenger Rear Support
Bracket (PFS/PCS/PRS)
Driver Rear Support
Bracket (DFS/DCS/DRS)
Passenger Rear Mounting
Bracket (PFM/PCM/PRM)
Driver Rear Mounting
Bracket (DFM/DCM/DRM)
Driver Center Mounting
Bracket (DFM/DCM/DRM)
Front
*All Driver Mounting Brackets are universal.
*All Driver Support Brackets are universal.
*All Passenger Mounting Brackets are universal.
*All Passenger Support Brackets are universal.
Torque Value
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 √
8mm 16-18 √
10mm 31-32 X
12mm 56-58 X
14mm 92-94 X

iArmor®
Rev. 20210801
2
Customer Support: [email protected]
STEP 1
Install the Step Pads onto the step bars with (32) M6X1-20mm
T-Bolts, (32) M6 Large Flat Washers and (32) M6X1Nylon Lock
Nuts.
IMPORTANT: Don’t hit the step pad by any metal hummer
within step pad installation, or the step pad will be damaged.
(8) M6X1-20 T-Bolts
(8) M6 Flat Washers
(8) M6 Nylon Lock Nuts
STEP 2
Front
(Fig 1) Driver Side Front Mounting Location
(No factory holes on pinch weld on some trims)
Starting installation from the driver side front of the vehicle,
remove the sealing tape covering the factory holes on the inner
side of body panel, (Fig 1). Note: All Mounting Brackets and
Supporting Brackets for Driver Side are the same.
M6 Large Flat
Washer
X68
M6X1-20 T-
Bolt
X44
M8 Bolt/Nut Plate
X6
Plastic Washer
X6
M8X1.25-30
Hex Bolt
X12
M8 Flat Washer
X18
M8 Lock Washer
X6
M6X1-25 Hex
Bolt
X12
M8X1.25 Nylon
Lock Nut
X6
M6X1 Nylon
Lock Nut
X56
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are
not responsible for any damage caused by the installation.
STEP 3
Determine the correct procedure to attach (1) Driver Front
Mounting Bracket (DFM/DCM/DRM) for your model/year:
Note: Rotate 90° after inserting the T-Bolts into the
Channel!!!

iArmor®
Rev. 20210801
3
Customer Support: [email protected]
(Fig 2) Insert M8 Bolt/Nut Plate (NOTE: M8 Bolt/Nut Plate is not
required on models with threaded inserts)
Models without factory threaded inserts in body panel:
a. Select (1) M8 Bolt/Nut Plate (Fig 2). Use the welded bolt as
a handle, insert the welded nut end through the oval factory
hole, and line up the welded nut with the hex hole. Thread (1)
M8 Plastic Washer onto the threaded end and down tight
against the body panel, (Fig 2). NOTE: The Plastic washer is
designed to keep the Bolt-Nut Plate out of falling into the
body panel and to aid in bracket installation.
b. Attach (1) Driver Front Mounting Bracket (DFM/DCM/DRM)
to the welded nut end of the M8 Bolt/Nut Plate on the driver
side front location with (1) M8 Flat Washer, (1) M8 Lock Wash-
er and (1) M8X1.25–30Hex Bolt, (Fig 3). Do not fully tighten at
this time.
Models with factory threaded inserts:
Attach Driver Front Mounting Bracket to the threaded inserts
with (1) M8x1.25-30 Hex Bolt, (1) M8 Lock Washer and (1) M8
Flat Washer, (Figs 4 & 5). Do not fully tighten at this time.
(Fig 3) Attach Driver Front Mounting Bracket to M8 Bolt/Nut Plate
M8 Bolt/Nut Plate
M8 Plastic Washer
(1) M8 Flat Washer
(1) M8 Lock Washer
(1) M8X1.25-30 Hex Bolt
M8 Bolt/Nut Plate
DFM
Front
Front
(Fig 4) Driver Side Front Mounting Location
(example of models with factory installed threaded inserts)
(1) M8X1.25-30 Hex Bolt
(1) M8 Lock Washer
(1) M8 Flat Washer
(Fig 5) Driver Front Mounting Bracket installed for models w/
factory threaded inserts (M8 Bolt/Nut Plate not required)
Front

iArmor®
Rev. 20210801
4
Customer Support: [email protected]
STEP 4
Attach the Driver Front Support Bracket (DFS/DCS/DRS) to the
Driver Front Mounting Bracket (DFM/DCM/DRM) with (1)
M8x1.25-30 Hex Bolt, (2) M8 Flat Washers and (1) M8X1.25
Nylon Lock Nut, (Fig 6).
Rotate and attach the support bracket to the back of the pinch
weld. Line up the slots in the top of the Support Bracket with
the (2) factory holes on the pinch weld. Secure the Bracket to
the back of the pinch weld with (2) M6x1-25 Hex Bolts, (4) M6
Flat Washers and (2) M6X1 Nylon Lock Nuts, (Fig 7). Do not
fully tighten hardware at this time.
IMPORTANT: Some models are not equipped with factory
holes and will require drilling through the pinch weld to
attach the Support Bracket. Do not drill through pinch weld
at this time, (Refer to Step 8).
Front
(1) M8X1.25-30 Hex Bolt
(2) M8 Flat Washers
(1) M8X1.25 Nylon Lock Nut
DFM/DCM/DRM
(Fig 7) Attach Driver Front Support Bracket to back of pinch
weld (models with factory holes on pinch weld only)
Front
(2) M6X1-25 Hex Bolts
(4) M6 Large Flat Washers
(2) M6X1 Nylon Lock Nuts
DFM/DCM/DRM
DFS/DCS/DRS
DFS/DCS/DRS
(Fig 6) Attach Driver Front Support Bracket to Drive Front
Mounting Bracket
STEP 5
Move to the Driver Side Center Mounting location, (Fig 8). Re-
peat Steps 3-4 to install and assemble the Driver Center
Brackets.
(Fig 8) Driver Side Center Mounting location
Front
STEP 6
Move to the Driver Side Rear Mounting location, (Fig 9). Re-
peat Steps 3-4 to install and assemble the Driver Rear Brack-
ets.
(Fig 9) Driver Side Rear Mounting Location
Rear

iArmor®
Rev. 20210801
5
Customer Support: [email protected]
STEP 7
Once all (3) Brackets have been installed, attach the Assem-
bled Driver Side Step Bar to the Mounting Brackets using (6)
M6X1-20 T-Bolts, (6) M6 Flat Washers and (6) M6X1 Nylon
Lock Nuts (Fig 10). Do not fully tighten hardware at this time.
STEP 9
Move to the passenger side of the vehicle. Repeat Steps 2-8 to
install the passenger side step bar.
NOTE: All Mounting Brackets and Support Brackets for passen-
ger side are the same.
STEP 8
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
Models requiring drilling for driver side Support Brackets:
a. Make sure the Step Bar is level to the vehicle. Adjust and
tighten all mounting hardware.
(6) M6X1-20 T-Bolts
(6) M6 Large Flat Washers
(6) M6X1 Nylon Lock Nuts
(Fig 10) Driver Side Step Bar Installed
Front
Attention
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
In order to protect your bars/boards, please use only mild soap/non-abrasive products for cleaning.
b. Line up the slots on the Support Brackets with the back of
the pinch weld. Mark the location of the slots onto the pinch
weld.
c. Drill (2) 1/4” holes through the pinch weld for each Support
Bracket. IMPORTANT: Do not drill too close to the bottom
edge of the pinch weld. Adjust the Brackets as necessary to
move the slots up the body panel away from the edge. Drill the
holes toward the outside of the marked slots.
d. Attach each Support Brackets to the pinch weld with (2)
M6X1-25 Hex Bolts, (4) M6 Large Flat Washers and (2) M6X1
Nylon Lock Nuts, (Fig 7). Check for level then fully tighten all
hardware.
Warning: Install the T-bolt on the step
bar and rotate it to 90 degrees!!!