iArmor EDGE IA-W171 User manual

Rev. 20220502
iArmor®
Customer Support: [e-mail]
1
PART#: IA-W171
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*ROCKER PANEL MOUNT
*DRILLING/TRIMMING NOT REQUIRED
Torque Value
IARMOR EDGE™
(PFM/PRM/DCM) (DFM/DRM/PCM)
Passenger Front /
Rear / Driver Center
Mounting Bracket
(PFM/PRM/DCM)
Driver Front / Rear /
Passenger Center
Mounting Bracket (DFM/
DRM/PCM)
PART LIST
Driver Side Step Bar Passenger Side Step Bar
Front
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18 √
10mm 31-32 √
12mm 56-58 X
14mm 92-94 X
(PFM/PRM/DCM)
Driver Center Mounting
Bracket 1 (DCM1)
Passenger Center Mounting
Bracket 1 (PCM1)
(DFM/DRM/PCM)

Rev. 20220502
iArmor®
Customer Support: [e-mail]
2
Hardware Package (For Brackets & Step Bars Installation)
Item QTY Description Item QTY Description
1# 16 M8X1.25-30 Hex Bolts 4# 16 M10X1.5-25 Hex Bolts
2# 16 M8 Large Flat Washers 5# 32 M10 Flat Washers
3# 16 M8 Lock Washers 6# 16 M10X1.5 Nylon Lock Nuts

Rev. 20220502
iArmor®
Customer Support: [e-mail]
3
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are
not responsible for any damage caused by the installation.
STEP 1
Start the installation under the driver side of the vehicle. Locate
the 6 plugs along the bottom edge of the body panel. Mounting
Brackets will bolt to the 1st, 3rd, 4th and 6th threaded mounting
holes, (Fig 1).
(Fig 1) Driver side Rocker Panel mounting locations
(For Some Models)
Front
STEP 2
Remove the plastic plugs from each mounting location if
equipped. Hold up a Mounting Bracket in place to determine
the mounting holes on the body panel, (Figs 2 & 3).
(Fig 2) Remove Plastic Plugs to Uncover Threaded Inserts
Front
Remove plugs if equipped
STEP 3
Select the Driver Front Mounting Bracket (DFM). Attach the
Bracket to the factory threaded holes with (2) M8X1.25-30 Hex
Bolts, (2) M8 Lock Washers and (2) M8 Large Flat Washers,
(Figs 4 & 5). Do not fully tighten hardware at this time.
(Fig 3) Driver Side Front Mounting Location
Front
(2) M8X1.25-30 Hex Bolts
(2) M8 Lock Washers
(2) M8 Large Flat Washers
(Fig 4) Driver Front Mounting Bracket Installation

Rev. 20220502
iArmor®
Customer Support: [e-mail]
4
Front
(2) M8X1.25-30 Hex Bolts
(2) M8 Lock Washers
(2) M8 Large Flat Washers
(Fig 5) Driver Front Mounting Bracket Installation
(Fig 6) Driver Side 2nd Mounting Location
(Fig 7) Driver Side 3rd Mounting Location
(Fig 8) Driver Side Rear Mounting Location
Rear
STEP 4
Move to the Driver Side 2nd, 3rd and rear Mounting Locations,
(Figs 6-9). Repeat Steps 1-3 to install the Driver Center &
Center 1 & Rear Mounting Brackets. Do not fully tighten hard-
ware at this time.
(2) M8X1.25-30 Hex Bolts
(2) M8 Lock Washers
(2) M8 Large Flat Washers
(Fig 9) Driver Center Mounting Bracket 1 (DCM1) Installation

Rev. 20220502
iArmor®
Customer Support: [e-mail]
5
STEP 5
Once all (4) Mounting Brackets have been installed, attach the
Driver Side Step Bar to the Mounting Brackets with (8)
M10X1.5-25 Hex Bolts, (16) M10 Flat Washers and (8)
M10X1.5 Nylon Lock Nuts, (Fig 10). Do not fully tighten hard-
ware at this time.
STEP 6
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use mild
soap/non-abrasive products for cleaning only.
STEP 7
Move to the other side of the vehicle. Repeat Steps 1-6 for the
other Side Step Bar installation.
(Fig 10) Driver Side Step Bar Installation
(8) M10X1.5-25 Hex Bolts
(16) M10 Flat Washers
(8) M10X1.5 Nylon Lock Nuts
Front
DCM1
DFM/PCM/DRM
Bottom View
DFM/PCM/DRM
DCM