iArmor EDGE User manual


1
iArmor®
CustomerSupport:[email protected]
Rev. 20200401

PART#:IA‐N111
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
Torque Value
Fastener Size Tightening Torque (ft-lbs)
6mm 6-7
8mm 16-18
10mm 31-32
12mm 56-58
14mm 92-94
IARMOREDGE™
Driver Front
Mounting Bracket
(DFM)
Driver Side Step Bar
Driver Center
Mounting Bracket
(DCM)
Driver Rear Mount-
ing Bracket (DRM)
Passenger Front
Mounting Bracket
(PFM)
Passenger Center
Mounting Bracket
(PCM)
Passenger Rear
Mounting Bracket
(PRM)
Driver Front Sup-
port Bracket (DFS) Passenger Front Sup-
port Bracket (PFS)
Driver Center Sup-
port Bracket (DCS)
Driver Center
Mounting Plate
(DCB)
Passenger Center
Support Bracket
(PCS)
Passenger Center
Mounting Plate (PCB)
Driver Rear Sup-
port Plate (DRS1)
Passenger Rear
Support Plate
(PRS1)
Passenger Rear
Support Bracket
(PRS)
Driver Rear Sup-
port Bracket (DRS)
Step Pad Step Pad
Passenger Side Step Bar
Front


2
iArmor®
CustomerSupport:[email protected]
Rev. 20200401
The instruction here is for your reference only. We
strongly recommend the professional installer for best
result. We are not responsible for any damage caused by
the installation.

STEP 1
Install the Step Pads onto the step bars with (32) M6X1-20 T-
Bolts, (32) M6 Flat Washers, (32) M6X1 Nylon Lock Nuts and
(8) M6X1-20 Flat Sunk Head Bolts. 
(8) M6X1-20 T-Bolts
(8) M6 Flat Washers
(8) M6 Nylon Lock Nuts
(2) M6X1-20 Flat Sunk Head
Bolts

STEP 2
Start installation on the passenger side of the vehicle. The
mounting brackets locations as shown on (Fig 1-3) Attach
brackets onto the holes in the pinch weld and the small factory
threaded hole directly behind the pinch weld. 
Front
Front
(Fig 1) Passenger Side Front Mounting
Location
Pair of holes on pinch weld
Threaded hole on
floor panel
M6X1-20
T-Bolt M6 Flat
Washer M6 Nylon
Lock Nut M6X1-20 Flat
Sunk Bolt
X 40 X 70 X 58 X 8
M8X1.25-35
Hex Bolt
M8X1.25-25
Hex Bolt
M8 Large
Flat Washer
M6X1-20
Square Head
Bolt
M8X1.25 Hex
Flange Nut M8X1.25-20
Inner Hex Bolt
M8 Lock
Washer
M8X1.25
Hex Nut
M6X1-25
Hex Bolt
X 4
X 6
X 4
X 14 X 4
X 8
X 22
X 8
X 12


3
iArmor®
CustomerSupport:[email protected]
Rev. 20200401

STEP 4
Install the Assembled Passenger Front Mounting Bracket on
the vehicle, (Fig 5). 

STEP 3
Assemble Passenger Front Mounting Bracket (PFM) and Pas-
senger Front Support Bracket (PFS) with (1) M8X1.25-25 Hex
Bolt, (2) M8 Flat Washers, (1) M8 Lock Washer and (1) M8
Hex Nut, (Fig 4). Don’t tighten hardware. 
(Fig 2) Passenger Side Center Mounting
Location
Front
Pair of holes on pinch weld
Threaded hole on
floor panel
(Fig 3) Passenger Side Rear Mounting
Location
Pair of holes on pinch weld
Threaded hole on
floor panel
PFM
PFS (1) M8X1.25-25 Hex Bolt
(2) M8 Flat Washers
(1) M8 Lock Washer
(1) M8 Hex Nut
(Fig 4) Passenger Front
Mounting Bracket
Assembly

STEP 5
Assemble the Passenger Side Center Mounting Bracket
(PCM) and Passenger side Center Support Bracket (PCS)
and Passenger Center Mounting Plate (PCB), (Fig 6).Don’t
tighten hardware. 
(2) M6X1-25 Hex Bolts
(4) M6 Flat Washers
(2) M6 Nylon Lock Nuts
(Fig 5) Passenger Front Mounting Bracket
Installed
(1) M8X1.25-35 Hex Bolt
(1) M8 Lock Washer
(1) M8 Flat Washer


4
iArmor®
CustomerSupport:[email protected]
Rev. 20200401

STEP 6
Install the Assembled Passenger Center Mounting Bracket on
the vehicle, (Fig 7).

STEP 8
Install the Assembled Passenger Rear Mounting Bracket on
the vehicle, (Fig 9). 

STEP 7
Assemble the Passenger Side Rear Mounting Bracket (PRM)
and Passenger side Rear Support Bracket (PRS) and Passen-
ger Rear Support Plate (PRS1), ( Fig 8).Don’t tighten hard-
ware. 

STEP 9
Once all (3) brackets are installed, attach the Assembled Pas-
senger Side Step Bar onto the Brackets, (Fig 10). 
(1) M8X1.25-35 Hex Bolt
(1) M8 Lock Washer
(1) M8 Flat Washer
(Fig 7) Passenger Side Center Bracket
Installed
(2)M6X1-25 Hex Bolts
(4)M6 Flat Washers
(2)M6 Nylon Lock Nuts
PRM
PRS1
(Fig 8) Passenger Rear
Mounting Bracket
Assembly
(2) M8X1.25-25 Hex Bolt
(4) M8 Flat Washers
(2) M8 Lock Washer
(2) M8X1.25 Hex Nut
PRS
(1) M8X1.25-35 Hex Bolt
(1) M8 Lock Washer
(1) M8 Flat Washer
(2) M6X1-25 Hex Bolts
(4) M6 Flat Washers
(2) M6 Nylon Lock Nuts
(Fig 9) Passenger Side Rear Bracket Installed
PCM
PCB
PCS
(Fig 6) Passenger Side Cen-
ter Mounting Bracket
Assembly
(2) M8X1.25-20 Inner
Hex Bolts
(2) M8X1.25 Hex Flange Nuts
(1) M8X1.25-25 Hex Bolt
(2) M8 Flat Washers
(1) M8 Lock Washer
(1) M8X1.25 Hex Nut


5
iArmor®
CustomerSupport:[email protected]
Rev. 20200401
Attention
In order to protect your bars/boards, please use only mild soap/non-abrasive products for cleaning.

STEP 10
Level and adjust the Assembled Step Bar properly and tight-
en all hardware. NOTE: Torque all M6 nylon lock nuts to 7 Ib-
ft. 

STEP 11
Repeat Step 2-10 for the Driver Side Step Bar installation.
Installation completed!!! 

STEP 12
Do periodic inspections to the installation to make sure that all
hardware is secure and tight.
Front
(4) M6X1-20 T-Bolts
(4) M6 Flat Washers
(4) M6 Nylon Lock Nuts
PFM
PCM
PRM
(2) M6X1-20 Square Head Bolts
(2)M6 Flat Washers
(2)M6 Nylon Lock Nuts
(Fig 10) Passenger Side Step Bar Installation