iArmor EDGE IA-W084 User manual

1Rev. 20220601
iArmor®
Customer Support: [e-mail]
PART#: IA-W084
BEFORE INSTALLATION
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE
PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION. ASSISTANCE IS RECOMMEND-
ED. THANK YOU FOR CHOOSING OUR PRODUCT!
*BODY FRAME MOUNT
*DRILLING/TRIMMING NOT REQUIRED
Torque Value
IARMOR EDGE™
Driver Rear Bar
Bracket (DRB)
Passenger Rear Bar
Bracket (PRB)
Passenger Front
Bar Bracket (PFB)
Driver Front Bar
Bracket (DFB)
PART LIST
Driver Side Passenger Side
Front
Fastener Size Tightening Torque (ft-lbs) Required
6mm 6-7 X
8mm 16-18 X
10mm 31-32 √
12mm 56-58 √
14mm 92-94 X
Mounting Bracket

2Rev. 20220601
iArmor®
Customer Support: [e-mail]
2#
1# 3# 6#
4# 7#
Hardware Package (For Brackets & Step Bars Installation)
Item QTY Description Item QTY Description
1# 4M12X1.75-35 Hex Bolts 5# 8M10X1.5-25 Hex Bolts
2# 8M12 Large Flat Washers 6# 16 M10 Flat Washers
3# 4M12 Lock Washers 7# 8M10X1.5 Nylon Lock Nuts
4# 4M12X1.75 Hex Nuts
5#

3Rev. 20220601
iArmor®
Customer Support: [e-mail]
The instruction here is for your reference only. We strongly
recommend the professional installer for best result. We are
not responsible for any damage caused by the installation.
STEP 1
Start installation from the front of the driver side of the vehicle.
Remove the factory body mount bolt, (Fig 1). Select (1) Mount-
ing Bracket. Insert the factory body mount bolt through the ap-
propriate slot of the mounting bracket, the rubber bushing and
back into the vehicle.
NOTE: Do not remove the rubber bushing. The Mounting
Bracket will install over the rubber bushing.
IMPORTANT: The Brackets are equipped with (2) mounting
slots.
Determine correct model/year for proper installation (Figs 2-3):
a. 1987 - 1995 Vehicles: Use the inner slot. Do not tighten
hardware at this time.
b. 1997 - 2006 Vehicles: Use the outer slot closer to the
bend in the Bracket. Do not tighten hardware at this time.
(Fig 1) Remove Factory Body Mount Bolt
1987 - 1995 Vehicles: Use
the inner slot
1997 - 2006 Vehicles: Use
the outer slot closer to the
bend in the Bracket
Re-use the factory hex bolt to attach
the Bracket to rubber bushing and
body mount
(Fig 3) Frame Bracket Installed
STEP 2
Select (1) Driver Front Bar Bracket (DFB), attach to the Mount-
ing Bracket with (1) M12X1.75-35 Hex Bolt, (2) M12 Large Flat
Washers, (1) M12 Lock Washer and (1) M12 Hex Nut, (Fig 4).
(Fig 2) Mounting Bracket

4Rev. 20220601
iArmor®
Customer Support: [e-mail]
(Fig 4) Driver Front Bracket Assembly
(1) M12X1.75-35 Hex Bolt
(1) M12 Lock Washer
(2) M12 Large Flat Washers
(1) M12 Hex Nut
STEP 3
Move to the Driver Side Rear Mounting Location, repeat Steps
1 & 2 for the Rear Brackets installation. (Fig 5).
(Fig 5) Driver Rear Bracket Assembly
(1) M12X1.75-35 Hex Bolt
(1) M12 Lock Washer
(2) M12 Large Flat Washers
(1) M12 Hex Nut
STEP 4
Once all (2) Brackets have been installed, attach the Driver
Side Bar to the assembled Bar Brackets with (4) M10X1.5-25
Hex Bolts, (8) M10 Flat Washers and (4) M10X1.5 Nylon Lock
Nuts, (Fig 6). Do not fully tighten hardware at this time.
Properly level and adjust the Step Bar and fully tighten all hard-
ware.
STEP 5
Move to the other side of the vehicle. Repeat Steps 1-4 for the
other side step bar installation.
Attention
Do periodic inspections to the installation to make sure
that all hardware is secure and tight.
In order to protect your bars/boards, please use mild
soap/non-abrasive products for cleaning only.
DFB
DRB
Mounting Bracket
Mounting Bracket

5Rev. 20220601
iArmor®
Customer Support: [e-mail]
(Fig 6) Driver Side Step Bar Installation
(4) M10X1.5-25 Hex Bolts
(8) M10 Flat Washers
(4) M10X1.5 Nylon Lock Nuts
Front
DFB
DRB
Bottom View