iNels RFGB-40 User manual

RFGB-20, RFGB-40,
RFGB-220, RFGB-240
x
RFRP-20
60 - 90 % 80 - 95 % 20 - 60 % 0 - 10 % 80- 90 %
1 /4
RFGB-20 RFGB-40 RFGB-220 RFGB-240
Glass touch controllers
EN
Characteristics
• The glass touch control is a design component of the RF Control system and is available in an elegant black and white variant.
• Thickness only 8 mm.
• RFGB-20 / RFGB-220: 2 capacitive buttons allow you to control 2 components.
• RFGB-40 / RFGB-240: 4 capacitive buttons allow you to control 4 components.
• When the button is pressed, it sends the set command (ON / OFF, dimming, time off / on, push/ pull). Transmission of the command is indicated by a red LED.
• Ability to set scenes where you control multiple iNELS RF Control devices with one press.
• The rear base allows screwing on the installation box, gluing with double-sided tape or just laying on the table.
• Battery power supply (2x 3 V battery CR 2032 - part of the package) with a lifespan of
approx. 2 years depending on the frequency of use.
• Range up to 200 m (outdoors), in case of insufficient signal between the controller and the device use the RFRP-20 signal repeater or devices with the RFIO2 protocol that support this
function.
• Communication frequency with RFIO protocol.
RF controlers can control:
• switches
RFSA-11B, RFSA-61B, RFSA-62B, RFSA-61M, RFSA-66M, RFSAI-61B, RFSC-11, RFSC-61, RFUS-11, RFUS-61, RFJA-12B
• dimmers
RFDA-73/RGB, RFDA-11B, RFDA-71B, RFDEL-71B, RFDEL-71M, RFDSC-11, RFDSC-71, RFDAC-71B
• lighting
RF-RGB-LED-550, RF-White-LED-675
Control options
Radio frequence signal penetration through various construction materials
brick walls wooden structures
with plaster boards
reinforced
concrete metal partitions common glass
EN
A NEW WAY OF PROGRAMMING!

CR2032
+
CR2032
+
1CR2032
+
CR2032
+
2
1
CR2032
CR2032
2
CR2032
3
CR2032
+
CR2032
+
3
2 / 4
Mounting jig (with brackets) - 1x
Battery*- 2x
* Batteries are inserted in the product. Before using for the rst time, remove the insulating tape from the battery contacts by pulling in the direction of the arrow.
Double-sided adhesive label - 4x
Package contents
Screws- 2x
After inserting the battery, the red LED lights up continuously for 3 seconds and then for 5 seconds, the selected controller function is indicated by flashing LED.
• triple flash - standard RFIO operating mode
• rapid flashing - mode of compatibility with older actuators
If you do not want to change the function of the controller, you must not press any buttons during this time
To switch between RFIO mode and compatibility mode:
If you need to change the operating mode of the controller, after inserting the battery, when the LED is constantly lit. press buttons 1 and 2 simultaneously and hold until the LED starts to
signal the changed mode (double flash or rapid flash).
Then the buttons must be released. The selected function mode is stored in memory and after replacing the battery, the controller continues to operate in the same mode.
If the controller is used in RFIO mode, then it is necessary to instruct the controller and link to the actuators switch to learn mode not only the actuator (according to the instructions for the
actuator), but also the controller in the following way:
Remove the battery from the controller, press some of the buttons several times to discharge the internal capacitors and replace the battery. When the LED lights up, press button 1 and keep
it pressed until the controller starts signaling the learning mode with short flashing LEDs. Then release the button and the button now works in RFIO learning mode. To end the learning mode,
remove the battery, press some of the buttons several times. and then replace the battery. Now we press any button and the controller will start again in RFIO operating mode.
Indicators, settings
Insertion and replacement of a battery
Press to open the plug-in battery
holder (you can use a flat-blade
screwdriver to open it).
Insert the CR2032 battery into
Battery holder. Watch out for
polarity.
Insert the holder into the device.
or
Never mix new and old batteries when replacing! It is always necessary to replace both batteries at the same time with new ones
Use a suitable tool (pa-
per clip, screwdriver)
to push on the control
pin. The batteries
are raised and the
programming button is
released.
After removing
the control flaps,
the programming
button is accessible.
The programming
button is operated
with a suitable thin
tool.

3 / 4
RFGB-20 RFGB-40 RFGB-220 RFGB-240
Technical parameters
More detailed information can be found in the iNELS RF Control Installation Manual:
https://www.elkoep.com/catalogs-and-brochures
ELKO EP, sro hereby declares that the type of radio equipment RFGB-20, RFGB-40,
RFGB-220, RFGB-240 is in accordance with Directives 2014/53 / EU, 2011/65 / EU,
2015/863 / EU and 2014 / 35 / EU. The full text of the EU Declaration of Conformity is
available on the following websites:
www.elkoep.com/glass-touch-controller---2-buttons-white-sharp
www.elkoep.com/glass-touch-controller---2-buttons-black-sharp
www.elkoep.com/glass-touch-controller---4-buttons-white-sharp
www.elkoep.com/glass-touch-controller---4-buttons-black-sharp
www.elkoep.com/glass-touch-controller---2-buttons-white-round--rfgb-220w
www.elkoep.com/glass-touch-controller---2-buttons-black-round-rfgb-220b
www.elkoep.com/glass-touch-controller---4-buttons-white-round-rfgb-240w
www.elkoep.com/glass-touch-controller---4-buttons-black-round-rfgb-240b
When handling a device unboxed it is important to avoid contact
with liquids. Never place the device on the conductive pads or
objects, avoid unnecessary contact with the components of the
device.
Safe handling
Attention:
When you instal iNELS RF Control system, you have
to keep minimal distance 1 cm between each units.
Between the individual commands must be an
interval of at least 1s.
Instruction manual is designated for mounting and also for user of the device. It is always a part of its packing. Installation and connection can be carried out only by a person with adequate
professional qualification upon understanding this instruction manual and functions of the device, and while observing all valid regulations. Trouble-free function of the device also depends on
transportation, storing and handling. In case you notice any sign of damage, deformation, malfunction or missing part, do not install this device and return it to its seller. It is necessary to treat
this product and its parts as electronic waste after its lifetime is terminated. Before starting installation, make sure that all wires, connected parts or terminals are de-energized. While mounting
and servicing observe safety regulations, norms, directives and professional, and export regulations for working with electrical devices. Do not touch parts of the device that are energized - life
threat. Due to transmissivity of RF signal, observe correct location of RF components in a building where the installation is taking place. RF Control is designated only for mounting in interiors.
The must not be installed into metal switchboards and into plastic switchboards with metal door - transmissivity of RF signal is then impossible. RF Control is not recommended for pulleys
etc. - radiofrequency signal can be shielded by an obstruction, interfered, battery of the transceiver can get flat etc. and thus disable remote control.
Warning
Power voltage:
Battery life:
Transmission indication:
Number of capacitive buttons:
Communication Protocal:
Frequence:
Signal transmission method:
Range:
Other data
Operating Temprature:
Working Position:
Mounting:
Protection:
Pollution degree:
Dimension:
Weight:
Related standards:
2x 3 V battery CR 2032
about 2 years depending on the frequency of use
Red LED
2 4 2 4
RFIO
866–922 MHz
one-way addressed message
in the open up to 200 m
-10 ... +50 °C
any
adhesive, screw
IP20
2
94 x 94 x 8 mm 100 x 100 x 8 mm
122 g 122 g 122 g 122 g
EN 60669, EN 300 220, EN 301 489 RTTE Directive,NV No. 426/2000 Coll. (Directive 1999 / EC)

1 3 2
1 32
13
Made in Czech Republic
4 /4
Push the brackets out of the
mounting fixture.
Assembly
Push the holders into the holes.
Free tting
Peel off one protective
layer on the doublesided
adhesive sheets and stick them
to the marked places on the
controller.
Peel off the second protective
layer on the double-sided
adhesive sheets and place the
control in the prepared place.
Adhesive
Depending on the type of
surface, clean (remove dust or
degrease) the place where
you want to place the controller.
Place the mounting jig on the
KU box and screw it on.
Screw
Snap on the controller.
ELKO EP, s.r.o. | Palackého 493 | 769 01 | Holešov, Všetuly | Česká republika
e-mail: [email protected] | EN Support: [phone] | CZ Technická podpora: [phone]
www.elkoep.com