Ingenico IWL 250 User manual

TERMINAL
User Guide1.0

V1.0 DRAFT (4.2017) Secure Table Pay Terminal User Guide i
Contents
Welcome.......................................................................................................................................1
1. Wireless Terminal Hardware....................................................................................................1
1.1 Terminal Base....................................................................................................................1
1.2 Terminal Power Up ............................................................................................................1
1.3 Terminal Function Keys .....................................................................................................2
1.4 Estimating the Number of Terminals..................................................................................3
1.5 Locating Communication and Charging Bases..................................................................4
1.5.1 Common Wireless Communication Obstacles:..........................................................5
1.6 Verifying Bluetooth Coverage............................................................................................5
1.6.1 Assessing Bluetooth Coverage during the Planning Phase.......................................5
1.6.2 Verifying Bluetooth Coverage after Equipment Delivery............................................6
1.7 Checking the Link between the Terminal and the Base ....................................................7
1.8 Assigning the Terminal to a Communication Base............................................................8
1.8.1 Resolving Communication Issues ..............................................................................8
1.9 Communication Base IP Address ......................................................................................8
1.9.1 Exchanging Bases......................................................................................................9
1.9.2 MAC Address............................................................................................................10
1.10 Charging the Battery and Assuring Maximum Battery Life............................................10
1.10.1 Battery Icon.............................................................................................................11
1.10.2 Correctly Charging New Batteries..........................................................................11
1.10.3 Replacing the Battery .............................................................................................12
1.11 Replacing the Paper Roll ...............................................................................................12
1.11.1 Paper Specifications and Storage..........................................................................13
1.12 Recommended Terminal Cleaning Instructions.............................................................13
2. Stand-Alone Admin Menu ......................................................................................................14
2.1 Extended Stand-Alone Setup Menu.................................................................................14
2.2 Setup/System Setup ........................................................................................................14
2.2.1 Changing the Terminal Date and Time ....................................................................15
2.3 Setup/Options ..................................................................................................................16
2.4 Print Setup .......................................................................................................................17
2.5 Reports.............................................................................................................................18
2.6 Maintenance.....................................................................................................................18
2.7 Help Desk.........................................................................................................................18
2.8 Training Mode..................................................................................................................20
2.9 Password Configuration...................................................................................................20
2.10 Info Screen.....................................................................................................................21
3. Stand-Alone Transaction Menu..............................................................................................22
3.1 Extended Stand-Alone Start (Transaction) Menu............................................................22
3.2 Sale..................................................................................................................................22
3.2.1 Adding a Tip..............................................................................................................23
3.2.2 Adding a Percent % Amount Tip ..............................................................................23
3.2.3 Adding a Tip Amount................................................................................................24
3.3 Refund..............................................................................................................................24
3.4 Void..................................................................................................................................25

ii SecureTablePay Terminal User Guide V1.0
DRAFT
3.5 Reprint..............................................................................................................................25
3.6 Force Post........................................................................................................................26
4. SecureTablePay.....................................................................................................................26
4.1 TGI Installation.................................................................................................................26
4.2 Get the POS (RMS) IP.....................................................................................................27
4.3 Terminal Configuration.....................................................................................................28
4.4 Terminal Status................................................................................................................29
4.5 Terminal Operation ..........................................................................................................29
4.5.1 Full Payment.............................................................................................................30
4.5.2 Adding a Tip..............................................................................................................31
4.5.3 Contactless Payment and Pay Including PIN...........................................................31
4.5.4 Cash Payment..........................................................................................................32
4.5.5 Split Payment ...........................................................................................................32
Index...........................................................................................................................................34
SecureTablePay™ is a trademark of POSERA Limited.
© Copyright 2017
POSERA Limited
All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means,
electronic, mechanical or otherwise, without the prior written permission of POSERA Limited.

V1.0 DRAFT Secure Table Pay Terminal User Guide 1
Welcome
SecureTablePay (STP) is a universal middleware platform that provides a EMV
1
processing
Pay at the Table (PATT) solution that can be connected to POS (Point of Sale) software.
This guide will explain accessing it using the Ingenico iWL250 wireless terminal keypad that
can work in a Stand-Alone state or a POS integrated payment version.
1. Wireless Terminal Hardware
1.1 Terminal Base
For POS operation:
•Each Terminal intelligent base will need
its own IP address and Ethernet
connection.
•The Terminals must be on the same
network as the POS (RMS2) computer.
‒Connect the Ethernet and then the
electrical power to the back of the
Terminal base (Figure 1)
Figure 1
1.2 Terminal Power Up
If the Terminal is on its base and turned off, hold the keypad [.,#*] button for 3 seconds to turn it
ON.
The Terminal will go through a sequence of screens before reaching its main operating screen.
NOTE: If Screen: PLEASE CHECK BASE means if the power to the Terminal base is
disconnected.
Terminal Power Down
NOTE: The Terminal can be powered down when it is not on its base.
Hold the keypad [.,#*] and [Yellow Correction] keys together for 3 seconds.
To turn the Terminal ON, place the Terminal on its base to start it up or if it is not on its base,
press the Green Enter key to turn it on.
Reboot the Terminal
When the Terminal is connected to its base, holding the [.,#*] and [Yellow Correction] keys
together can be used as a reboot function.
1
EMV (Europay, MasterCard, Visa) is a global standard for credit cards that uses computer chips to
authenticate (and secure) chip-card transactions.
2
RMS (Restaurant Management System)
Rear view of Terminal base
Ethernet
Power

2Secure Table Pay Terminal User Guide V1.0
DRAFT
1.3 Terminal Function Keys
Figure 2
SecureTablePay Screen
When the Terminal starts up, it will show the
SecureTablePay version screen (Figure 2).
TID 123: This is the 8-digit Terminal identification number.
SWIPE/KEY SERVER: This is a prompt for the Server to
log on to the payment system by either:
•Swiping their ID Card at the right side of the Terminal.
•Inserting their ID Card at the bottom of the Terminal.
•Key in their identification PIN code on the Terminal
Keypad. Press the Green Enter key at the bottom,
right of the keypad to continue.
•Main Function F-Key (above the Red Cancel key)
‒Press to access, example: Stand-Alone state or
SecureTablePay.
•Red Cancel key (bottom, left of keypad).
‒Press to back out of or stop a keypad entry.
•Yellow Correction key (bottom, middle of keypad).
‒Press to remove a key entry.
•Green Enter key (bottom, right of keypad).
‒Press to continue a selection.
Terminal Dimensions: 6.5 (l) x 2.1 (H) x 3.1(W) inches [165 (l) x 54 (H) x 78 (W) mm]
Terminal Weight: 10 oz. (300g)


F1 F2 F3 F4
Up/Down Arrow Buttons
Function Keys
Figure 3
TID 123
SWIPE/KEY SERVER

V1.0 DRAFT Secure Table Pay Terminal User Guide 3
1.4 Estimating the Number of Terminals
Before they can be ordered, the number of terminals, communication and charging bases need
to be estimated for your specific installation sites. The following factors may affect the number
of terminals necessary for a specific site:
1. The type of business: restaurant, hotel, night club, bar, lounge, theatre, department store,
jeweler, travel agent, pharmacy, etc.
2. The size and layout of the dining room lounge or room where business is conducted and
the number of separate floors or dining rooms.
3. The number of tables (for restaurants) or payment stations (for other businesses, place
where a client may use the terminal to perform a payment).
4. The maximum number of credit and debit card transactions performed on the busiest day
of the peak time or season.
5. The possibility of wireless communication obstacles (refer to section: 1.5.1 Common
Wireless Communication Obstacles).
6. The maximum number of terminals that can be assigned to one communication base is
seven, but the optimal number could be less because:
‒If a communication base goes out of order, the business is less affected if there are
other communication bases available for use.
‒If the communication base has too many terminals assigned to it and if the
communication is dial, the telephone line becomes congested. The optimum number
should then be no more than 4. If the communication is Ethernet, there is usually no
congestion.
7. The communication base also charges the terminal placed on it. However, to have all
terminals adequately charged, it is recommended that there is one charging base for each
of the other terminals so that each terminal has its own charger.
Use the following guidelines for your estimate:
1. If estimating the number of terminals and bases necessary to replace currently installed
countertop terminals, one communication base and one terminal is probably needed to
replace each of the existing countertop terminals. This is based on no change in the
current host communication (dial or Ethernet).
2. If estimating equipment for a new site, consider the need for a planned number of tables or
payment stations.
3. For up to 10 tables or payment stations on a single floor, a reasonable estimate is one
terminal and one communication base.
4. From 11 to 30 tables or payment stations, two terminals are probably needed, one
communication and one charging base.
5. For more than 30 tables or payment stations, at least three terminals are probably needed,
one communication and two charging bases.
6. If the site has more than one floor where customers can be served and if the number of
tables or payment stations does not justify additional terminals, trying to install a
communication base only on the main floor to assess performance for a period of about
one week, is encouraged. Additional terminals and bases can be ordered later, if needed
and if the merchant is prepared to install additional communication lines on the other floors.

4Secure Table Pay Terminal User Guide V1.0
DRAFT
7. After having calculated the initial number of terminals and bases using the above
guidelines, this number may need to be adjusted considering the transaction volume during
peak hours. The number of planned terminals and bases could be increased if a higher
volume is expected. This volume depends on the following:
‒The average time customers spend at the table or at the payment station before making
a payment. Example: customers of a fast food restaurant can stay for a shorter time
than those of a regular restaurant.
‒The number of transactions paid by card (debit or credit) considered as a percentage of
the total number.
8. Finally, consider the terminal / server ratio. This ratio is about 1 to 4 (one terminal for
approximately 4 servers). This ratio should not be used to estimate the number of
terminals, but instead as a confirmation of the number of terminals that were estimated
using the previous guidelines.
Now confirming where to install communication and charging bases is necessary.
1.5 Locating Communication and Charging Bases
After estimating the required equipment, define where to place the communication and
charging base(s). Remember that a communication base might need to be relocated due to
possible wireless coverage problems.
The following guidelines help to choose where to locate the base(s):
1. When replacing a countertop terminal, the first choice is to place the communication base
where the countertop used to be, provided the rest of the considerations in this list are
satisfied.
2. Wireless coverage may not be satisfactory if the communication base is close to a wireless
communication obstacle (refer to section: 1.5.1 Common Wireless Communication
Obstacles).
3. A communication base needs a telephone or Ethernet line (depending on the configuration)
and an electrical power outlet nearby.
4. A charging base needs an electrical power outlet nearby.
5. Two communication bases cannot be placed within two meters (6.5 feet) of each other. In
general, Bluetooth devices (not Ingenico specific) can affect performance of Wi-Fi devices
(because their frequency ranges are overlapping) –it is recommended to keep iWL
Bluetooth terminals away from Wi-Fi routers, access points and other Wi-Fi devices.
6. Terminals and bases should stay where they can be monitored by the staff.
7. Locating multiple bases to gain optimum coverage in a multi-floor, multi-obstruction
environment takes some time and effort. It is achieved through trial and error or previous
installation experience.
NOTE: If the terminal is left with minimal monitoring, the application must provide
password control to prevent unauthorized use. This happens, example: if there are
additional bases installed on a different floor.

V1.0 DRAFT Secure Table Pay Terminal User Guide 5
8. Probably the most difficult task when planning where to place a communication base is to
predict potential wireless communication obstacles. As a general rule, the communication
base should be placed away from the obstacles listed next:
1.5.1 Common Wireless Communication Obstacles:
•Microwave ovens
(minimum distance: 3 m or 9.8 ft.)
•Portable phones
•Mobile/cellular phones
•Security radios, walkie-talkies
•Mirrors
•Metallic blinds
•Steel cabinets
•Blenders and food processors
•Computers
•Wireless routers
•Cash registers
•EPOS front-ends (Electronic Point of Sale)
•Groups of people
•Televisions
•Plasma screens
•Ventilation fans
•Elevator shafts
•Air conditioning units
•Any large vertical metal plane
(fridges, doors, large appliances, vending
machines, etc.)
If the guidelines established in the current section were followed and those in section: 1.4
Estimating the Number of Terminals, all the information needed to place the order for the
equipment should be complete.
1.6 Verifying Bluetooth Coverage
Under normal conditions, it should not be necessary to assess wireless coverage before
ordering equipment.
It should be adequate to follow the guidelines established in sections: 1.4 Estimating the
Number of Terminals and 1.5 Locating Communication and Charging Bases.
If there appears to be no reason to assess Bluetooth coverage before ordering equipment,
proceed to section: 1.6.2 Verifying Bluetooth Coverage after Equipment Delivery.
1.6.1 Assessing Bluetooth Coverage during the Planning Phase
A prior Bluetooth coverage assessment should be performed, only if there is reason to suspect
that the number of terminals and bases that were calculated is very incorrect and there is no
time to verify and correct the estimate and then re-order after the first equipment delivery
arrives.
1. Remember that certain equipment works on an intermittent basis (example: air conditioning
units). The assessment should be conducted when this equipment is on. The testing
should be performed in the live environment –in busy hours if possible: Kitchen and other
equipment running, premises filled with guests (as human bodies as well as personal
mobile devices can be considered wireless obstacles).
2. A communication base and a terminal will be needed to perform this assessment.
NOTE: The assessment is only useful and valid if all the furniture and equipment
(especially regarding the conditions listed under section: 1.5.1 Common Wireless
Communication Obstacles) are installed and working on the site to be assessed.

6Secure Table Pay Terminal User Guide V1.0
DRAFT
3. Install the communication base at the planned location. Follow the installation instructions
provided with the base.
4. Assign the terminal to the base if it has not been done. This procedure is described in
section: 1.8 Assigning the Terminal to a Communication Base.
5. Fully charge the terminal battery. Information on how to care for the battery is in section:
1.10 Charging the Battery and Assuring Maximum Battery Life.
6. Test the wireless link as described in section: 1.7 Checking the Link between the
Terminal and the Base. Remember that it is necessary to walk around with the terminal
and perform the test at each table or payment station where you suspect coverage will be
weak.
7. Specifically, testing the tables or payment stations located:
‒Far away from the base.
‒Near to wireless communication obstacles (refer to section: 1.5.1 Common Wireless
Communication Obstacles).
‒On other floors (if applicable).
‒On outside patios or external areas (if applicable).
‒Where there are screens or other physical obstacles between the terminal and the base.
1.6.2 Verifying Bluetooth Coverage after Equipment Delivery
1. After receiving the equipment, follow the instructions in the Installation Guide (inside the
box and together with the hardware received) to install the equipment.
2. Follow the instructions in the application documentation to initialize the terminal with the
host. If you need to set up the terminal to work with the communication base (refer to
section: 1.8 Assigning the Terminal to a Communication Base).
3. After installing the equipment, fully charge the battery (refer to section: 1.10 Charging the
Battery and Assuring Maximum Battery Life) and initialize the terminal with the host,
verify wireless coverage is excellent throughout the dining room, lounge or room. This can
be done in two ways:
4. By checking the connection monitoring mechanisms. This is described in section: 1.7
Checking the Link between the Terminal and the Base.
5. By using a payment application transaction or function that communicates with the host to
test the Bluetooth link as described in the next paragraph.
6. Perform the transaction at each table or payment station where communication is expected
to be weak. Use a transaction or function that does not cause a financial charge at the host
(that does not charge your bank account or credit card, refer to section: 2.8 Training
Mode). Example: a balance inquiry or a host totals inquiry.
7. Specifically, test the tables or payment stations located:
‒Far away from the base.
‒Near to wireless communication obstacles (refer to section: 1.5.1 Common Wireless
Communication Obstacles).
‒On other floors (if applicable).
‒On outside patios or external areas (if applicable).
‒When there are screens or other physical obstacles between the terminal and the base.
NOTE: The coverage verification is only useful and valid if all the furniture and equipment
(especially regarding the conditions listed under section: 1.5.1 Common Wireless
Communication Obstacles) are installed and working on the site to be verified.

V1.0 DRAFT Secure Table Pay Terminal User Guide 7
8. Remember that certain equipment works on an intermittent basis (example: air conditioning
units). Conduct the verification when this equipment is on.
9. If the terminal cannot establish the Bluetooth link, it displays a communication error
message or other similar message defined in your payment application indicating that
coverage is weak. If the message comes frequently, it indicates that there are coverage
problems. In this case, consider the following solutions:
‒Removing or relocating the possible radio communication obstacles.
‒Ordering another communication base and terminal to cover the area that has
problems.
1.7 Checking the Link between the Terminal and the Base
The Bluetooth status is displayed on the top left side of the screen which has signal strength
bars that display the quality of the link.
This test checks the communication strength between the terminal and the base at the specific
place where the terminal is when it is powered on.
The connection monitoring mechanisms use a wireless frequency probe that is sent at least
once per second from the terminal to the base. When the base gets the wireless frequency
probe, it will update information, and send it back to the terminal. The time between the
moment when the terminal sends a wireless frequency probe and the moment it receives the
response serves as a way of determining the link quality.
When the link quality indicator is displaying its maximum signal strength bars, it is the normal
state of operation.
The terminal is considered no longer connected if less than 2 bars are displayed.
Follow these steps to test the wireless link:
1. Go to the table or payment station that will be tested.
2. The terminal must be powered off to start the test.
3. Remove the terminal to be powered off from its base.
4. Power off the terminal by pressing the [.,#*] and [Yellow Correction] keys at the same time.
5. Power on the terminal by pressing the Green Enter key.
6. Wait until the status bars are displayed and check the number of Bluetooth signal strength
bars for reception quality.

8Secure Table Pay Terminal User Guide V1.0
DRAFT
1.8 Assigning the Terminal to a Communication Base
This option logically assigns a terminal to a communication base. This option needs to be done
only if the terminal is not assigned or, if it needs to be re-assigned to another base.
With the Terminal connected to its communication Base, refer to section: 2.6 Maintenance
When in the Stand-Alone Setup Menu (refer to section: 2. Stand-Alone Setup Menu), press
the number 4 key on the keypad for the Terminal Maintenance.
Terminal Screen: ASSOCIATION SUCCESSFUL
This will assign the Terminal to the base it is on.
1.8.1 Resolving Communication Issues
If a communication problem is experienced:
1. Turn off the terminal and its base (unplug power from base).
2. Verify Ethernet is plugged into the base.
3. Turn base on (plug power in).
4. Turn terminal on.
For new installations, always plug Ethernet into the base before powering up the base by
plugging in power to the base. Once the base is powered, Terminals associated with that base
can be turned on.
1.9 Communication Base IP Address
When a terminal is associated with a communication base, it establishes a private PPP link to
the base. All communications with the outside world are managed by the base.
Each base can also be configured manually through menu options (see “Menu” column in the
following table).
Parameter
Description
Value
Application
Prompt
Default
Menu
Item
Menu
Terminal
IP
IP address
used by the
Ethernet
base.
15 Digits,
Numeric
Enter
Terminal IP
Empty
Yes
STANDALONE / Admin
/ SETUP / SYSTEM
SETUP / TCPIP SETUP
/ STATIC
IP
SubMask
IP Subnet
Mask
Address.
15 Digits,
Numeric
Enter IP
Subnet
Mask
Empty
Yes
Same as above.
GatewayIP
Internet
Gateway IP
address
15 Digits,
Numeric
Enter
Gateway IP
Empty
Yes
Same as above.
IPType
Select
dynamic or
static IP
addressing.
1=DHCP
(Dynamic)
2=Static
Not
applicable.
1=DHCP
No
Set by selection in
STANDALONE / Admin
/
SETUP / SYSTEM
SETUP / TCPIP SETUP

V1.0 DRAFT Secure Table Pay Terminal User Guide 9
This manual configuration for a base is done using one of the hand-held terminals assigned to
it and it will be done only once (using 1 hand-held terminal). Reboot other hand-held terminals
assigned to this base once the base configuration is completed.
Example: assign static IP addresses to different bases using one terminal.
1. Assign a handheld terminal to its default base.
2. Enter the static IP settings under the Stand-Alone menu for the base through
STANDALONE \ Admin \ SETUP \ SYSTEM SETUP \ TCPIP SETUP \ STATIC.
3. Within the STATIC IP menu, set the Terminal IP, Gateway IP and IPSubMask.
4. Repeat steps above for the next base.
Note if downloading configuration parameters into handheld terminals (remotely or locally):
Depending on the merchant’s requirements and environment, they may want to use Static IP
settings. In this case, the downloaded parameters listed in the previous table should be left as
blank and IP type set to 2 = Static. When the download is completed, assign terminal(s) to
base(s) as per merchant’s requirements and manually configure Ethernet parameters of the
base(s) using one of the terminals assigned to that base.
1.9.1 Exchanging Bases
If a base will need to be replaced at a merchant site, review the information shown above to
determine Ethernet Setup of the base. The association of all terminals assigned to the old base
can then be removed.
The new base can then be exchanged –connected to Ethernet first followed by connecting
power. All terminals can then be re-associated to the new base as outlined in section: 1.8
Assigning the Terminal to a Communication Base.
If the base is set to Static, the Base Static IP settings can then be entered through one of the
terminals assigned to the new base with the previous information.
If the base is set as Dynamic (DHCP), the above steps do not need to be performed, other than
assigning the terminals to the replacement base.

10 Secure Table Pay Terminal User Guide V1.0
DRAFT
1.9.2 MAC Address
The following image is a label from the bottom of a terminal base. The third line shows the
MAC address if the merchant requires it for registration on their network.
1.10 Charging the Battery and Assuring Maximum Battery Life
The terminal is supplied with a lithium-
ion removable battery.
Feature
Description
Battery Type
Lithium-ion
Battery Power Rating
2050 mAh
Recharge time
4 hours from empty to full charge
Powering mode
‒Putting the terminal on the base.
‒Pressing the Green Enter key.
Many adaptors may appear similar and plug into the base but do not work properly, causing
erratic behavior, poor charging or even damage to the base.
To charge the battery, place the terminal on the base. Verify the base is powered up. Note that
the battery recharges only if necessary.
NOTE: Only use the battery pack and power adaptor supplied with the terminal.

V1.0 DRAFT Secure Table Pay Terminal User Guide 11
1.10.1 Battery Icon
1 bar represents from 1% to 20% of full capacity.
2 bars represent from 21% to 40% of full capacity.
3 bars represent from 41% to 60% of full capacity.
4 bars represent from 61% to 80% of full capacity.
5 bars represent from 81% to 100% of full capacity.
•For IWL2xx, the battery is judged to be very low (critical level), when the measured value is
less than 7%.
•The terminal displays a warning indicating a low battery when the battery level is
approximately less than 7% and the terminal is not being powered by the base.
•If the battery status is low, the application displays a low battery warning and it is not
possible to perform any transaction or admin function.
1.10.2 Correctly Charging New Batteries
Following these recommendations will extend the battery life:
•Before using a terminal for the first time, charge the battery until the battery charge icon
indicates battery is fully charged.
•Full charging time after the first time is 4 hours or until the battery indicator indicates fully
charged.
•Every one or two months, allow the terminal to show the low battery warning and shut down
(exhaust the battery charge completely). Then fully charge the battery.
•Batteries that are not used for extended periods of time without charging gradually self-
discharge.
•To prolong the life of batteries that are not used for a long time: store them at room
temperature and charged to 2 or 3 bars. Check the charge level every couple of months and
recharge to 2/3 bars if needed.
The maximum number of transactions performed with a full battery charge varies
considerably. It could range up to 1000 depending on the following:
‒The number of receipt copies printed.
‒The size and format of receipts and reports.
‒The transaction frequency and duration.
‒The average distance between the terminal and the communication base.
‒The time the payment application takes to go into sleep mode.
‒The amount of time the terminal remains off the base.
‒The age of the battery.

12 Secure Table Pay Terminal User Guide V1.0
DRAFT
1.10.3 Replacing the Battery
Follow these steps to replace the battery:
1. Remove the terminal from its base and press the [.,#*] and [Yellow Correction] keys at the
same time to turn it off, before handling the battery.
2. Turn the terminal over to the bottom showing, with the smart card reader facing down.
3. Press down the latches at the back of the terminal, under the paper compartment, to
release the cover.
4. Disconnect the battery connector and then remove the battery.
5. Connect the new battery connector to the terminal and replace the battery.
6. Insert the two small teeth that come out from the lower part of the cover, into the two
notches at the bottom of the battery compartment opening.
7. Press the upper part of the cover against the terminal, until the release latches click back
into place. Ensure that the cover is firmly attached to the terminal.
8. Turn the terminal on by pressing the Green Enter key.
1.11 Replacing the Paper Roll
The terminal features an easy-loading printer for fast and easy replacement of paper rolls.
The paper roll is equipped with a low paper warning red (or another color) stripe. When the red
stripe appears, it is time to replace the paper roll. Also, refer to section: 1.11.1 Paper
Specifications and Storage for more information about paper.
Li-ion battery
2050mAh
Battery
connector

V1.0 DRAFT Secure Table Pay Terminal User Guide 13
Paper Compartment Diagram
Refer to the diagram while
performing these steps to replace
the paper roll:
1. Pull the large tab, behind the
paper conveyer slot, toward the
front and lift open the cover.
2. Remove the empty paper roll.
3. Insert the new roll of paper as
indicated in the image on the
right.
4. Close the paper compartment
door.
1.11.1 Paper Specifications and Storage
Only Ingenico approved paper rolls should be used.
Feature
Paper Roll Description
Paper Type
Paper thermal color White
Width
2.2 in (56 mm)
Length
Approx. 56 ft. (17 m)
Diameter
1.6 in (40 mm)
1.12 Recommended Terminal Cleaning Instructions
Plastic Part Cleaning
Do not use any type of alcohol because it will damage the plastic parts.
To clean the plastic parts:
1. Use Ingenico wipes part number 296118801.
2. Use damp but not fluffy cloth (damp with soapy water).
For more details please go to the Ingenico web site: http://ingenico.cleaningcards.com
Smart Card Reader and MSR Head Cleaning
To clean the Smart card reader pins and Magnetic head, Ingenico advises the use of cleaning
cards part number 296118799.
For more details please go to the Ingenico web site: http://ingenico.cleaningcards.com
When stored, thermal paper should not be exposed to:
‒Vinyl, plastics, adhesives, shrink-wraps, wet-toner copies or carbon papers.
‒Office light, UV light.
‒High humidity (above 65% relative humidity).
‒Temperatures above 25 degrees Celsius (77 degrees Fahrenheit).

14 Secure Table Pay Terminal User Guide V1.0
DRAFT
2. Stand-Alone Admin Menu
To enter the Stand-Alone Admin Menu, press the F-Key, above
the Red Cancel key (Refer to 1.2 Terminal Function Keys,
Figure 2).
A selection will appear on the screen to choose Stand-Alone or
Menu for SecureTablePay.
Press the F1 key under F1 on the screen to enter the Stand-
Alone state.
Enter the Admin Password: defaulted to 6 zeros: 000000 (refer
to section: 2.9 Password Configuration to change the
password) and press the Green Enter key at the bottom, right of
the keypad.
Press the F1 key under Setup for the Stand-Alone Menu.
Stand-Alone Setup Menu
Press the corresponding key number on the keypad for the
numbered menu selection on the screen.
2.1 Extended Stand-Alone Setup Menu
To access additional Stand-Alone Setup Menu selections, press
the Down arrow, between the Terminal Function Keys (Refer to
1.2 Terminal Function Keys, Figure 3).
To return to the previous menu selections, press the Up arrow,
between the Terminal Function Keys (Figure 3).
2.2 Setup/System Setup
When in the Stand-Alone Setup Menu, press the number 2 key on the keypad to enter the
Terminal Setup.
Screen: 1. OPTIONS 2. SYSTEM SETUP
CHOOSE
F1 F4
F4->MENU
F1->STANDALONE
ENTER
ADMIN PASSWORD
TID 123
WELCOME
Setup Start
4. MAINTENANCE
1. REPORTS
2. SETUP
3. PRINT SETUP
8. INFO SCREEN
5. HELP DESK
6. TRAINING MODE
7. PWD CONFIG

V1.0 DRAFT Secure Table Pay Terminal User Guide 15
Press 2 for System Setup.
Screen: ADMIN PASSWORD + OK
Enter the Admin Password: defaulted to 6 zeros: 000000 and press the Green Enter key.
2.2.1 Changing the Terminal Date and Time
NOTE: The Batch must be cleared to change the date and time or, they will not display.
If necessary, the Batch can be cleared by going to STANDALONE\Setup\5. HELP DESK\2.
CLEAR BATCH. WARNING: Clearing the Batch will delete all transactions. Confirm the Host
received all transactions first.
Screen: TERMINAL DATE (YYYYMMDD) + OK
Enter the current date as the full year, month number, day and press the Green Enter key.
Press the Green Enter key to continue if the date is already set and acceptable.
Press the Red Cancel key to exit.
Screen: TERMINAL TIME (HHMM) + OK
100 Hours Military Time
Time entries are in 100 hours or Military Time.
Refer to the following table for the time values to enter.
AM
100 Hours
AM
100 Hours
PM
100 Hours
PM
100 Hours
12:00
(Midnight)
00:00
6
06:00
12:00
(Noon)
12:00
6
18:00
1
01:00
7
07:00
1
13:00
7
19:00
2
02:00
8
08:00
2
14:00
8
20:00
3
03:00
9
09:00
3
15:00
9
21:00
4
04:00
10
10:00
4
16:00
10
22:00
5
05:00
11
11:00
5
17:00
11
23:00
Enter the current time as the hour and minute and press the Green Enter key.
Press the Green Enter key to continue if the time is already set and acceptable.
Press the Red Cancel key to exit.
The date and time will display in the
Terminal Status Bar, above the screen.
Continued after Date and Time settings if they display in System Setup:
Screen: 1. DNS SETUP 2. TERMINAL SETUP
Press 1 for DNS Setup.
Screen: AUTOMATIC DNS YES
NO YES
Press the F1 key under NO or the F4 key under YES and press the Green Enter key.
If the setting is already done and acceptable, press the Green Enter key to continue.
Press 2 for Terminal Setup.
TID 123
Terminal
Bluetooth
Comms Connection 02/16/2017
3:
Date
Time Battery
5
Network

16 Secure Table Pay Terminal User Guide V1.0
DRAFT
Screen: 1. NONE 2. DYNAMIC 3. STATIC
Press 1 for None.
Press 2 for Dynamic to automatically get the IP address for the terminal.
Press 3 for Static Screen: TERMINAL ADDRESS + OK to enter an IP address. Press the Green
Enter key to continue.
NOTE: These selections can restart the terminal.
2.3 Setup/Options
Screen: 1. OPTIONS 2. SYSTEM SETUP
Press 1 for Options.
Screen: ADMIN PASSWORD + OK
Enter the Admin Password: defaulted to 6 zeros: 000000 and press the Green Enter key.
Screen: TIP OPTION YES
NO YES
Press the F1 key under NO or the F4 key under YES and press the Green Enter key.
If the setting is already done and acceptable, press the Green Enter key to continue.
Screen: TIP PRESET 1 + OK 10
10
This is the first preassigned Tip percentage that can be selected when a payment using the
Terminal is made.
Keep the setting or enter a new setting.
Press the Green Enter key to continue.
Screen: TIP PRESET 2 + OK 15
15
This is the second preassigned Tip percentage that can be selected when a payment using the
Terminal is made.
Keep the setting or enter a new setting.
Press the Green Enter key to continue.
Screen: ENTER LAST 4 DIGITS NO
NO YES
After a credit card, has been used in the Terminal, this setting provides a prompt to enter the
last 4 digits of the credit card number for confirmation.
Press the F1 key under NO or the F4 key under YES and press the Green Enter key.
If the setting is already done and acceptable, press the Green Enter key to continue.
When in the Stand-Alone Setup Menu, press the corresponding
key number on the keypad for the numbered selection on the
screen.
4. MAINTENANCE
1. REPORTS
2. SETUP
3. PRINT SETUP