Intrinsyc APQ8096 User manual

Open-Q™ µ820 (APQ8096) Development Kit
Quick Start Guide
Your use of this document is subject to and governed by those terms and conditions, https://www.intrinsyc.com/legal-terms/qualcomm-terms.html, in the Intrinsyc Purchase and Software License Agreement for the Open-Q™ micro 820 Development Kit based on the Qualcomm® Snapdrag-
on™ 820 Processor (APQ8096), which you or the legal entity you represent, as the case may be, accepted and agreed to when purchasing an Open-Q™ micro 820 Development Kit from Intrinsyc Technologies Corporation (“Agreement”). You may use this document, which shall be considered part
of the defined term “Documentation” for purposes of the Agreement, solely in support of your permitted use of the Open-Q™ micro 820 Development Kit under the Agreement. Distribution of this document is strictly prohibited without the express written permission of Intrinsyc Technolo-
gies Corporation and its respective licensors, which they can withhold, condition or delay in its sole discretion.
Intrinsyc is a trademark of Intrinsyc Technologies Corporation, registered in Canada and other countries. Qualcomm and Snapdragon are trademarks of Qualcomm Incorporated, registered in the United States and other countries.
Package Contents
1. IO Expansion header EDU
2. Mini PCI Express socket *
3. Power buon
4. Volume + buon
5. Volume - buon
6. 3 x LEDs
7. WWAN SIM card slot *
8. PCI Express slot
9. Sensors header
10. 12V DC jack
11. USB debug UART Micro B
12. USB 3.0 Expansion connector
13. USB 2.0 OTG Micro AB
14. Dual stacked USB 3.0 type A
15. Baery connector
16. HDMI out
17. General purpose buon
18. Power header
19. ANC 3.5 mm headset jack
20. GPS ext. ant. SMA connector
21. Boot conguraon DIP switches
22. MIPI camera 2 connector
23. Micro SD slot *
24. MIPI camera 1 connector
25. Open-Q µ820 System on Module
(SOM)
26. GPS module WGR7640
27. 32GB UFS
28. 3GB LP-DDR4 RAM Pop memory
on top of Snapdragon APQ8096
processor
29. WLAN module QCA6174
30. MIPI camera 0 connector
31. Audio out header
32. SOM power measurement
header
33. Audio in header
34. Hapcs output header
35. MIPI DSI LCD/touchscreen
connector to interface with
Intrinsyc display adapter
* on boom side
1. Open-Q™ 820 µSOM with APQ8096 processor
2. Carrier board
3. AC Power Adapter
4. 4.5” FWVGA MIPI DSI LCD/touchscreen (addional accessory)
14958
11
12
14
16
20
2224
31
36
18
13
15
23
17
33
10
21
19
30
35
7
2
27 29
26
25
28
34
32

Open-Q™ µ820 (APQ8096) Development Kit
Quick Start Guide
Specifications are subject to change - Open-Q µ820 DK QSG Rev. 1.0
Development Kit Setup
1. Remove the development kit board carefully from the anti static bag
2. Connect the HDMI cable from the development kit to a display
3. Connect the Power Adapter to the development kit then press once
the power button (S100), after approximately 30 seconds the board will
boot automatically
4. Documentation and software
To access the documentation (schematics, user guides, datasheets,
programming guides, tech notes…), platform BSP software and much more,
please register at: http://support.intrinsyc.com
Development Kit Support
For more information or assistance, you can contact us at:
https://www.intrinsyc.com/contact-support
Intrinsyc also provides technical information and videos on Snapdragon processors at:
http://www.intrinsyc.com/resources
Should you require additional technical support for your Development Kit you can
purchase a block of technical support hours from the Intrinsyc store:
https://www.intrinsyc.com/support
Thank you for purchasing the Open-Q µ820 Development Kit
The Intrinsyc Team