Intrinsyc Open-Q 212A User manual

Open-Q™ 212A Development Kit
Quick Start Guide
14
2
Your use of this document is subject to and governed by those terms and conditions, https://www.intrinsyc.com/legal-terms/qualcomm-terms.html, in the Intrinsyc Purchase and Software License Agreement for the Open-Q™ 212A Development Kit based on the Qualcomm® Snapdragon™
212 Processor (APQ8009), which you or the legal entity you represent, as the case may be, accepted and agreed to when purchasing an Open-Q™ 212A Development Kit from Intrinsyc Technologies Corporation (“Agreement”). You may use this document, which shall be considered part of the
defined term “Documentation” for purposes of the Agreement, solely in support of your permitted use of the Open-Q™ 212A Development Kit under the Agreement. Distribution of this document is strictly prohibited without the express written permission of Intrinsyc Technologies Corpora-
tion and its respective licensors, which they can withhold, condition or delay in its sole discretion. Intrinsyc is a trademark of Intrinsyc Technologies Corporation, registered in Canada and other countries. Qualcomm and Snapdragon are trademarks of Qualcomm Incorporated, registered in the
United States and other countries. Other product and brand names used herein may be trademarks or registered trademarks of their respective owners.
Package Contents
1. Open-Q™ 212A SOM with APQ8009 SoC
2. Open-Q™ 212A Carrier Board
3. AC Power Adapter
4. Camera Adaptor Board (Oponal Accessory)
1. WLAN Antenna 1 (PCB Trace)
2. Conguraon DIP switches
3. Automaon Header
4. Power header
5. BT Antenna (PCB trace)
6. MIPI-CSI Camera 0 Connector*
7. Digital Audio Codec header
8. Baery Charging header
9. MIPI-CSI Camera 1 Connector*
(not supported)
10. USB Type-C Connector (not sup-
ported)
11. 12V DC Power jack
12. GPS External Antenna Connector
13. Accessory header (sensors, etc.)
14. GPS PCB Antenna*
15. Power Source Switch (Ba/DC)
16. Baery connector
17. USB Debug UART Micro B
18. SOM Power Probe header
19. Speaker Connector
20. WLAN Antenna 2 (PCB Trace)
21. USB Type-A Dual Stack Host
22. Audio Expansion Header
23. Micro-USB port
24. MIPI-DSI LCD/Display Connector*
25. Headset Connector
26. Power Buon
27. Volume + buon
28. Volume - buon
29. HDMI Connector
30. Wi-Fi U.FL Antenna 1 Connector
31. Wi-Fi U.FL Antenna 0 Connector
32. BT U.FL Antenna Connector
33. WLAN/BT Module
34. GPS U.FL Antenna Connector
35. Snapdragon APQ8009 CPU
36. Open-Q 212A System on Module
(SOM)
* ON BOTTOM SIDE
17
35
8
22
13
Specifications are subject to change - Open-Q 212A DK QSG Rev. 1.0
34
20
29
24
25
23
21
19
26
32
31
30
7
9
6
5
10
11
1216 15
1
27
28
33
34
36
18

Open-Q™ 212A Development Kit
Quick Start Guide
Specifications are subject to change - Open-Q 212A DK QSG Rev. 1.0
Development Kit Setup
1. At a static-safe workstation, remove the development kit board
carefully from the anti static bag.
2. Connect the serial debug USB (17) to your favorite terminal program if
you wish to see boot messages (FTDI UART — USB bridge driver
required on PC).
2. Connect the Power Adapter to the 12V DC Jack (11) and then press
and hold the POWER ON button (26) for a few seconds until the blue
LED starts blinking to indicate the board is booting up.
3. Documentation and software
To access the documentation (schematics, user guides, datasheets,
programming guides, tech notes…), platform BSP software and much more,
please register at:
http://tech.intrinsyc.com
Development Kit Support
Should you require more information or assistance, you can contact us at:
https://www.intrinsyc.com/contact-support
Intrinsyc also provides technical information and videos on Snapdragon processors at:
https://www.intrinsyc.com/resources
Should you require additional technical support for your Development Kit you can
easily purchase a technical support package from the Intrinsyc store:
http://shop.intrinsyc.com/collections/technical-support-packages
Thank you for purchasing the Open-Q 212A Development Kit
The Intrinsyc Team