Intrinsyc Open-Q 835 uSOM User manual

Open-Q™ 835 uSOM (APQ8098)
Development Kit
Your use of this document is subject to and governed by those terms and conditions (https://www.intrinsyc.com/legal-terms/qualcomm-terms.html) in the Intrinsyc Purchase and Software License Agreement for the Open-Q™ 835 uSOM Development Kit based on the Qualcomm® Snapdrag-
on™ 835 Processor (APQ8098), which you or the legal entity you represent, as the case may be, accepted and agreed to when purchasing an Open-Q™ 835 uSOM Development Kit from Intrinsyc Technologies Corporation (“Agreement”). You may use this document, which shall be considered
part of the defined term “Documentation” for purposes of the Agreement, solely in support of your permitted use of the Open-Q™ 835 uSOM Development Kit under the Agreement. Distribution of this document is strictly prohibited without the express written permission of Intrinsyc Tech-
nologies Corporation and its respective licensors, which they can withhold, condition or delay in its sole discretion.
Intrinsyc is a trademark of Intrinsyc Technologies Corporation, registered in Canada and other countries. Qualcomm and Snapdragon are trademarks of Qualcomm Incorporated, registered in the United States and other countries.
Other product and brand names used herein may be trademarks or registered trademarks of their respective owners.
Package Contents
1. WLAN/BT PCB Antenna
2. Misc interface header (GPIO)
3. Power buon
4. Volume + buon
5. Volume - buon
6. User LEDs (red, blue green)
7. PCIe 1X Slot
8. Sensor expansion header
9. 12V DC input jack
10. Debug UART (USB MicroB)
11. USB Type-C connector
12. Baery charge cong switch
13. SOM Power voltage adjust
14. Baery connector
15. Power source switch
16. HDMI video output
17. Power header
18. 3.5 mm headset jack
19. Conguraon DIP switches
20. MIPI camera 2 connector
21. Micro SD slot (on boom)
22. MIPI camera 1 connector
23. MIPI camera 0 connector
24. Audio Out Expansion Header
25. SOM power measurement
header
26. Power and Charging LEDs
27. Audio In Expansion Header
28. Hapc output header
29. WLAN PCB Antenna
30. MIPI DSI LCD/touchscreen
connector to interface with
Intrinsyc display adapter
31. UFS ash memory
32. APQ8098 CPU with PoP RAM
33. Wi-Fi RF secon under shield
34. WLAN antenna connector 1 U.FL
35. WLAN antenna connector 2 U.FL
36. Open-Q 835 µSOM
1. Open-Q™ 835 µSOM with APQ8098 processor
2. Open-Q™ 835 µSOM Carrier board
3. AC Power Adapter
4. HDMI Video Cable
5. 4.5” FWVGA MIPI DSI LCD/touchscreen (oponal accessory)
134
10
12
16
2022
24
25
13
27
9
19
18
23
30
31 33
3435
32
29
25
11
26
36
28
21
678
14
15
17

Open-Q™ 835 uSOM (APQ8098)
Development Kit
If you have previously registered on our support site for a different product then
please contact us to request support access for your new product:
https://www.intrinsyc.com/contact-support
Please include the platform name (Open-Q 820, 410 etc.) and the SOM serial
number in your message.
Development Kit Support
For more information or assistance, you can contact us at:
https://www.intrinsyc.com/contact-support
Intrinsyc also provides technical information and videos on Snapdragon processors
at:
http://www.intrinsyc.com/resources
Should you require additional technical support for your Development Kit you can
purchase a block of technical support hours from the Intrinsyc store:
https://www.intrinsyc.com/support
Thank you for purchasing the Open-Q 835 µSOM Development Kit
The Intrinsyc Team
Development Kit Setup
1. At a static-safe workstation, remove the development kit board
carefully from the anti-static bag
2. If you do not have the optional LCD then connect the HDMI cable from
the development kit (#16) to an HDMI display.
3. Connect the Power Adapter to the 12V DC Jack (#9), then press and
hold the power button (#3) for approximately 3 seconds. If using the LCD
you will see the boot menu appear first, followed by the Intrinsyc logo as
the board boots up. If using HDMI the screen will remain blank for
approximately 45 seconds before the Android screen appears.
4. Documentation and software
To access product documentation (schematics, user guides, programming
guides, tech notes…), platform BSP software and much more, please register
your product on our support site at the link below.
https://support.intrinsyc.com/login
Specicaons are subject to change - Open-Q 835 uSOM DK QSG rev 1.2