Ironman Fitness 5800 User manual

The specifications of this product may vary from this photo and are subject to change without notice.
IRONMAN, IRONMAN TRIATHLON and M-DOT are registered trademarks of World Triathlon Corporation.
This product is licensed by the World Triathlon Corporation.
OWNER’S MANUAL
Inversion Table
Item#5800
5800.5‐120216

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
If you need help with product information, assembly, or
replacement parts. Please contact customer service.
Email us at:
[e-mail]
Or call us at:
1-844-641-7922
Hours:
8:00 am to 5:00 pm (PST) Daily

STOP
ARRÊT
ALTO

SERVICE -------------------------------------------------------------------------2
LABEL PLACEMENT --------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES ------------------------------------- 4
OVERVIEW DRAWING ------------------------------------------------------ 6
PARTS LIST --------------------------------------------------------------------- 7
HARDWARE & TOOLS PACK ---------------------------------------------- 9
ASSEMBLY ----------------------------------------------------------------------10
SAFETY OPERATING INSTRUCTIONS ---------------------------------16
OPERATION AND ADJUSTMENTS ---------------------------------------17
STORAGE & TROUBLESHOOTING SECTION ----------------------- 20
WARRANTY -------------------------------------------------------------------- 21
PART REQUEST FORM ----------------------------------------------------- 22
TABLEOFCONTENTS
1

IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any
other service support, please contact our customer service department
(8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods:
For Best Service, please Email:
[e-mail]
Response Time: 1-2 Business Days
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7922
Response time may vary.
Please have the following information ready when requesting for service:
Your name
Phone number
Model number
Serial number
Part number
Proof of Purchase
For damaged or defective product please contact our customer service
before returning to the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA
SERVICE
2

LABELPLACEMENT
3

Read all instructions before using the Inversion Table. When using an Inversion table,
basic precautions should always be followed, including the following:
WARNING - To reduce the risk of injury to persons:
1. Make sure your equipment is correctly assembled before you use it.
2. Be sure all screws, nuts, and bolts are tightened prior to use.
3. The equipment weighs more than 44lbs / 20kgs and should be assembled and moved by two or more
people.
4. Only one person should use the equipment at a time.
5. Never operate this Equipment if it is damaged, If it is not working properly, has been dropped, or
damaged. If a problem is encountered contact Customer Service before using the equipment again.
6. Always use this equipment on a clear and level surface.
7. For household use only.
8. Do not use outdoors or near water.
9. Use the inversion table only for its intended use as described in this manual. Do not use
attachments not recommended by the manufacturer.
10. Do not wear loose clothing when using the equipment.
11. Keep all hands and feet away from any moving parts.
12. Never drop or insert any object into any opening.
13. Always wear shoes when using the inversion table.
14. Close supervision is necessary when the inversion table is used near children, or by or near invalids
or disabled persons.
15. Listen to your body. It is recommended that you rotate up and down slowly. Dizziness might occur if
you come up too fast.
16. If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop
exercising immediately. You should also stop exercising if you are experiencing pain or any discomfort.
17. Wait 2 hours after eating before using the inversion table. If you start feeling nauseous, return to the
upright position slowly.
18. For any problems contact customer service. Servicing should be performed by an authorized service
representative. Our contact number is on the service page.
19. Warning:- Risk of Personal Injury - Consult with your personal physician to see if inversion
equipment is appropriate for you. This is especially important for people with pre-existing health
problems. Do not use this equipment without your physician's approval.
20. Warning:- Risk of Personal Injury – Do not allow children to use this machine.
21. Warning:- Risk of Personal Injury - Keep children under the age of 13 away from the machine
while in use.
22. Warning:- Risk of Personal Injury – Keep body parts, hair, loose clothing, and jewelry
clear of all moving parts.
23. Warning:- Risk of Personal Injury - Tilt-back slowly when inverting. Failure to comply could
result in serious bodily injury.
24. Warning: - Risk of Personal Injury - Do not attempt to service the unit yourself. Discontinue
use and contact customer service.
IMPORTANTSAFETYGUIDELINES
4

25. Warning: - To Reduce The Risk Of Personal Injury - Read And Understand All Read The
Instructions Before Using The Inversion Table.
Do not use this equipment if you have any of the following conditions or ailments:
Pregnancy
Extreme obesity
Middle ear infection
Hiatus hernia or Ventral hernia
Glaucoma, retinal detachment or conjunctivitis
Use of anticoagulants includingAspirin in high doses.
Spinal injury, Cerebral Sclerosis, or acutely swollen joints
Heart or circulatory disorders for which you are being treated
High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack
Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted
orthopedic supports.
Do not exceed the maximum rated weight (load) and maximum rated
user height:
The Maximum Weight Capacity for this product is 275lbs/125kgs.
Retain this owner’s manual and keep the original purchase receipt for
future reference.
SAVE THESE GUIDELINES
5
IMPORTANTSAFETYGUIDELINES

OVERVIEWDRAWING
6

No. Description Qty No. Description Qty
1 FrontU-Frame 1 28 Upper Bed Frame Bushing 1
2 RearU-Frame 1 29 Handlebar 2
3 Adjustable Boom 1 30 Knob 1
4 Bed Frame 1 31 Rubber Heel Holder 4
5 Pivot Arm 2 32 Nylon Strap 1
6 Adjustable Lock Plate 1
33 Loop Strap 1
7 Steel Heel Holder Bracket 4 34 Strap Lock 1
8 Folding Arm 2
35 FoamBed 1
9 Rear Rod 1 36 Foam Grip 2
10 Bolt M8x23 2 37 Protective Cover 2
11 FrontRod 1 38 Hex Head Bolt M8x23 2
12 Phillips Screw M6x35 4 39 Front Plastic Cover 1
13 Washer Ø20xØ8.5x1.5 17 40L Left Plastic Cover 1
14 Round Plate 1 40R Right Plastic Cover
1
15 Lock Nut M8 12 41 Square End Cap 2
16 Lock Nut M6 6 42 Lock Pin 1
17 BlockingBushØ28.5xØ23x14 2 43 Hex Head BoltM8x43 2
18 Large Spring Knob 1 44 HeightScale 1
19 Safety Hook 2 45 Latch 1
20 RubberPad 1 46 Foam Bed Bolt 5
21 Oval End Cap 2 47 Bolt M4x16 1
22L Left Adjustable Boom Plate 1 48 Bolt M6x20 2
22R Right Adjustable Boom Plate 1 49 Front Right Foot Cap 1
23 In-StepFrame 2 50 Front Left Foot Cap 1
24 In-Step Foot Pad 2 51 BoltM6x15 2
25 Round End Cap 4 52 End Cap (
□ 25x50mm) 5
26 Lower Bed Frame Bushing 2 53 Foam Grip 2
27 Washer Ø12xØ6.5x1.0 4 54 Washer Ø13x6.5x1.0 4
PARTS LIST
7

No. Description Qty No. Description Qty
55 Nut Cap Ø27xØ13.5
4
67 ScrewST4.2x12 8
56 AdjustableHandle 1 68 ScrewST4.8x20 1
57 HandleCap 1 69 Shaft Nut Ø8 1
58 HandleSpring 1 70 BoltM5x10 2
59 Button 1 71 BoltM8x50 4
60 HandleTip 1 72 Pivot Arm Ring 2
61 BlockingBushØ28.5xØ22.5x10 2 73 Rear Left Foot Cap with Handle
Ⅰ
1
62 ScrewM3x10 10 74 Rear Left Foot Cap with Handle
Ⅱ
1
63 Bolt M6x15 1 75 Rear Right Foot Cap with Handle
Ⅰ
1
64 CarriageBolt M8x70 2
76 Rear Right Foot Cap with Handle
Ⅱ
1
65 BoltM6x30 1 77 Screw ST3.5x15 8
66 SpacerØ22xØ16.8 2
PARTS LIST
8

9
HARDWARE&TOOLSPACK

The product weighs more than 44lbs/20kgs and should
be assembled and moved by two or more people.
8
2
1
77
75
76
73
74
77
49
50
54
48
54
51
48
51
Step 1:
Stand up the base of the machine by separating the Front and Rear
U-Frames (1, 2). Pull the Front and Rear U-Frames (1, 2) apart from each
other. Push down on the middle of the Folding Arms (8) until they are fully
locked down.
Attach each of the Right & Left Foot Caps (49, 50) to the Front & Rear
U-Frame (1, 2) with one Screw (48), one Screw (51), and two Washers (54).
Tighten using the Multi Hex Tool with Phillips Screwdriver provided.
Attach the Rear Left Foot Cap with Handle I (73) and Rear Left Foot Cap
with Handle II (74) to the left side of the Rear U-Frame (2) with four Screws
(77). Attach the Rear Right Foot Cap with Handle I (75) and Rear Right Foot
Cap with Handle II (76) to the right side of the Rear U-Frame (2) with four
Screws (77). Then tighten using the Multi Hex Tool with Phillips Screwdriver
provided.
Hardware:
ASSEMBLY
(54) Washer
4 PCS
(48) Bolt
2 PCS (51) Bolt
2 PCS
10
(77) Screw
8PCS
Multi Hex Tool with
Phillips Screwdriver
Tool:

37
2
1
55
15
55
4
5
5
Step 2:
Install a Nut Cap (55) onto the Lock Nuts (15). Slide a Protective Cover
(37) on to each side of the base as shown. Pull down on the Protective Covers
(37) until the bottom of the covers are slightly lower than the Folding Arms (8).
Use the Velcro straps on the bottom of the Protective Covers (37) to secure the
covers to the Folding Arms (8). When the covers are assembled correctly, the
Folding Arms (8) should be fully covered by the Protective Covers (37).
Step 3:
Slide the bottom of the Pivot Arms (5) into the brackets that are located on
each side of the Bed Frame (4). Align the arms with the desired hole on the arm
with the peg on the bracket. Insert the peg into the hole to lock the Pivot Arms
(5) in place. It is recommended that you use the bottom hole on the Pivot Arms
(5) until you become more familiar with the equipment.
ASSEMBLY
11
(55) Nut Cap
2 PCS

2
5
9
7
7
31
31
11
31
3
7
7
31
Step 4:
Mount the Bed Frame (4) to the Rear U-Frame (2) by inserting the ends of
the Pivot Arms (5) into the channels on the plates. The slotted portion of the
rollers on the end of the Pivot Arms (5) should be inserted into the channels on
the plates.
Step 5:
Slide the Steel Heel Holder Brackets (7) and Rubber Heel Holders (31)
onto both ends of the Rear Rod (9). Ensure the lock teeth are wedged into the
slots in Rear Rod (9) as shown in the figure above. Repeat this step to install
the Steel Heel Holder Brackets (7) and Rubber Heel Holders (31) onto the
Front Rod (11).
NOTE: Make sure the lock teeth are wedged into the slots in the Rear and
Front Rods (9, 11) before use.
ASSEMBLY
12

4
3
30
18
10 178
11 180
12 183
185
13
14 188
190
15
16 193
17 195
18 198
19 200
20 203
21 205
22 208
23 210
203
24
205
25
44
Step 6:
Pull out the Large Spring Knob (18) and slide the Adjustable Boom (3) into
the square bracket on the bottom of the Bed Frame (4) as shown.
Slide the Adjustable Boom (3) to the desired height.
Lock the Adjustable Boom (3) in place by releasing the Large Spring
Knob (18) and sliding the Adjustable Boom (3) up or down slightly until the
Large Spring Knob (18) "pops" down into the locked position. Secure the
Knob (30) onto the back side of the bracket on the Bed Frame (4) as shown.
ASSEMBLY
13

13 15
29
43
13 13
15
38 13
2
72
55
Step 7:
Attach the top end of the Handlebar (29) onto the Rear U-Frame (2) and
Pivot Arm Ring (72) with one Hex Head Bolt (38), one Lock Nut (15), and two
Washers (13). Attach the bottom end of the Handlebar (29) onto the Rear
U-Frame (2) with one Hex Head Bolt (43), one Lock Nut (15), and two
Washers (13). Tighten all Bolts and Nuts using the Multi Hex Tool with
Phillips Screwdriver, and Hex Wrench provided. Attach a Nut Cap (55) onto
Hex Head Bolt (38).
Repeat this step to attach the other Handlebar (29) on the opposite side of
the Rear U-Frame (2).
Hardware:
ASSEMBLY
14
(15) Lock Nut
4 PCS
(13) Washer
8 PCS
(38) Hex Head Bolt
2 PCS
(43) Hex Head Bolt
2 PCS
(55) Nut Cap
2 PCS
Multi Hex Tool with
Phillips Screwdriver
Tool:
Hex Wrench

19 3433 32 19
19 33 34 32 19
34
32
1
4
19
19
33
Step 8:
Attach the Nylon Strap (32) to the Strap Lock (34) by inserting the end of
the
Nylon Strap (32) up through the bottom of the Strap Lock (34), loop the Nylon
Strap (32) over the Pre-assembled Loop Strap (33) and down through the Strap
Lock (34). Then loop the strap back over itself, and insert back through the Strap
Lock (34), and pull tight to secure. See Diagram above.
Step 9:
Attach the Nylon and Loop Straps (32, 33) to the inversion table by hooking
the end of the Nylon Strap (32) to the loop on the back of the Bed Frame (4) as
shown. Then hook the other end of Loop Strap (33) to the other Pre-assembled
loop on the Front U-Frame (1) as shown above.
ASSEMBLY
15

16
SAFETYOPERATINGINSTRUCTIONS
WARNING: Make sure both pivot arms are in the same hole to
prevent serious injury from occurring.
Make sure the pivot arm is inserted all
the way into the slot. When the Pivot
arm is aligned correctly in the groove
of the curved slot the pivot arm will be
able to move freely.
CorrectIncorrect
The slot of the Pivot arm is NOT aligned
correctly. The pivot arm must be inserted
all the way into the curved slot.

4
18
3
30
A nylon strap has been included to restrict the degree of inversion. This
strap can be adjusted to different lengths to allow for a greater or lesser
degree of inversion. To lengthen the Nylon Strap (32) feed the top end of
Nylon Strap (32) into the strap lock, and pull on the lower end of
the strap. To shorten the length feed the bottom end of Nylon Strap (32) into
the strap lock, and pull on the top end. See Diagram above.
ADJUSTING THE BOOM
The Adjustable Boom (3) can be moved to a variety of different positions,
in order to accommodate users of different heights. To adjust the boom loosen
the Knob (30), pull out the Large Spring Knob (18) and slide the boom up or
down to the desired height. The height scale is positioned just below the Square
Bushing (26). When the boom is in the desired position, release the Large
Spring Knob (18), slide the boom slightly up or down until the Large Spring
Knob (18) locks into place, and tighten the Knob (30).
OPERATIONANDADJUSTMENTS
32 32
SHORTEN LENGTHEN
THE STRAP
17

PIVOT ARMS
The Pivot Arms (5) can be adjusted to allow for a greater or lesser degree of
inversion. To adjust the Pivot Arms (5) simply pull out on them until the post is
out of the hole, slide them up or down to the desired holes. The bottom hole
provides the least amount of inversion, while the top hole provides the greatest
amount. It is recommended that beginners use the bottom hole until they are
familiar with the inversion table.
Note: Both Pivot Arms (5) must be adjusted to the same hole. Trying to
adjust the Pivot Arms (5) on two different positions could cause damage to
the inversion table, or injury to the user.
THE HANDLEBARS
For added convenience and safety, a set of Handlebars (29) has been
added to the inversion table. The Handlebars (29) are there to help the user
return to the upright position from any degree of inversion. If you wish to return to
the upright position, and the bed is moving too slowly, or not moving at all, simply
grab the Handlebars (29) and pull on them until you return to the upright position.
Note: The inversion table should always return to the upright position when you
move your hands below your waist. If it does not, the inversion table is probably
not adjusted correctly to your height.
GENERAL PRECAUTIONS
1. Make sure that the Pivot Arms (5) are locked on the lowest holes for the first
few attempts.
2. It is recommended that someone be with you while you are using this inversion
table for the first few times.
3. Make sure that the Rubber Heel Holders (31) are holding your feet securely.
4. Make sure that the Adjustable Boom (3) is properly set to your height.
5. Make sure that the Adjustable Boom (3) is held securely by both the Large
Spring Knob (18) and the Knob (30).
6. Make sure that there is enough room for the bed to rotate completely.
18
OPERATIONANDADJUSTMENTS
4
5