Ironman Fitness Gravity 4000 User manual

5402.6-060117

PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE.
STOP. Contact customer service if you have any questions
regarding assembly or proper operation of the machine.
Email us at:
[e-mail]
Or call us at:
1-844-641-7922
Hours:
8:00 am to 5:00 pm (PST) Daily

1
TABLE OF CONTENTS
SERVICE ------------------------------------------------------------------------- 2
LABEL PLACEMENT --------------------------------------------------------- 3
IMPORTANT SAFETY GUIDELINES ------------------------------------- 4
OVERVIEW DRAWING ------------------------------------------------------- 6
PARTS LIST ---------------------------------------------------------------------- 7
HARDWARE & TOOLS PACK----------------------------------------------- 9
ASSEMBLY ----------------------------------------------------------------------- 10
OPERATION & ADJUSTMENTS -------------------------------------------- 17
STORAGE & TROUBLESHOOTING --------------------------------------- 21
WARRANTY ---------------------------------------------------------------------- 22
PART REQUEST FORM ------------------------------------------------------- 23

2
SERVICE
IMPORTANT: FOR NORTH AMERICA ONLY
For damaged or defective product, questions, replacement parts or any other service
support, please contact our customer service department
(8:00 AM - 5:00 PM Pacific Standard Time, Daily) by the below methods:
For The Best Service, please Email:
[e-mail]
Response Time: 1-2 Business Days
Emailing us with the information above will be the best method to receive a response during
peak business hours
Website:
www.paradigmhw.com
Toll-Free:
1-844-641-7922
Response time may vary via calling
Refer to our email for the best response time
Please have the following information ready when requesting for service:
•Your name
•Phone number
•Model number
•Serial number
•Part number
•Proof of Purchase
For damaged or defective product please contact our customer service before returning to
the store.
Paradigm Health & Wellness, Inc.
1189 Jellick Ave.
City of Industry, CA 91748, USA

3
LABEL PLACEMENT
Please Keep All Body Parts,
Hair, Loose Clothing, and
Jewelry away from all moving
parts.
S'il vous plaît garder toutes les
parties du corps, les cheveux,
les vêtements amples, et jewlery
loin de toutes les pièces mobiles
WARNING AVERTISSEMENT
For Household Usage Only Pour un usage domestique seulement
hold
To
and

4
IMPORTANT SAFETY GUIDELINES
Read all instructions before using the Inversion Table. When using an Inversion table, basic
precautions should always be followed, including the following:
WARNING - To reduce the risk of injury to persons:
1. Make sure your equipment is correctly assembled before you use it.
2. Be sure all screws, nuts, and bolts are tightened prior to use.
3. The equipment weighs more than 44lbs / 20kgs and should be assembled and moved by two or more
people.
4. Before using this equipment, we recommend doing warm ups.
5. Only one person should be using the equipment at a time.
6. Never operate this Equipment if it is damaged, if it is not working properly, has been dropped, or
damaged. If a problem is encountered contact Customer Service before using the equipment again.
7. Always use this equipment on a clear and level surface.
8. For household use only.
9. Do not use outdoors or near water.
10.Use the inversion table only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
11.Do not wear loose clothing when using the equipment.
12.Keep all hands and feet away from any moving parts.
13.Never drop or insert any object into any opening.
14.Close supervision is necessary when the inversion table is used near children, or by or near invalids, or
disabled persons.
15.Listen to your body. It is recommended that you rotate up and down slowly. Dizziness might occur if you
come up too fast.
16.If at any time you feel faint, light-headed, or dizziness while operating the equipment, stop exercising
immediately. You should also stop exercising if you are experiencing pain or any discomfort.
17.Wait at least 2 hours after eating before using the inversion table. If you start feeling nauseous, return to
the upright position slowly.
18.For any problems contact customer service. Servicing should be performed by an authorized service
representative. Our contact number is on the service page.
19.Warning: - Risk of Personal Injury - Consult with your personal physician to see if inversion
equipment is appropriate for you. This is especially important for people with pre-existing health problems.
Do not use this equipment without your physician's approval.
20.Warning: - Risk of Personal Injury – Do not allow children to use this machine.
21.Warning: - Risk of Personal Injury - Keep children under the age of 13 away from the machine.
22.Warning: - Risk of Personal Injury – Keep body parts, hair, loose clothing, and jewelry clear
of all moving parts.
23.Warning: - Risk of Personal Injury - Always hold on to the safety handles and tilt-back slowly when
inverting. Failure to comply could result in serious bodily injury.
24.Warning: - Risk of Personal Injury - Do not attempt to service the unit yourself. Discontinue use
and contact customer service.
25.Warning: - To Reduce The Risk Of Personal Injury - Read And Understand All Read The
Instructions Before Using The Inversion Table.

5
IMPORTANT SAFETY GUIDELINES
The product weighs more than 44 lbs. It is heavily
recommended that at least 2 Persons assemble.
Do not use this equipment if you have any of the following conditions or ailments:
•Pregnancy
•Extreme obesity
•Middle ear infection
•Hiatus hernia or Ventral hernia
•Glaucoma, retinal detachment or conjunctivitis
•Use of anticoagulants including Aspirin in high doses.
•Spinal injury, Cerebral Sclerosis, or acutely swollen joints
•Heart or circulatory disorders for which you are being treated
•High blood pressure, Hypertension, Recent stroke or Transient Ischemic attack
•Bone weaknesses including Osteoporosis, Unhealed fractures, Modular pins, or surgically implanted
orthopedic supports.
Do not exceed the maximum rated weight (load) and maximum rated
user height:
The Maximum Weight Capacity for this product is 350lbs/159kgs.
The Maximum Rated Height this product is 6’6”/198cm.
Retain this owner’s manual and keep the original purchase receipt
for future reference.
SAVE THESE GUIDELINES

6
OVERVIEW DRAWING

7
PARTS LIST
No.
Description
Qty
No.
Description
Qty
1
Front U-Frame
1
33
Loop Strap
1
2
Rear U-Frame
1
34
Strap Lock
1
3
Adjustable Boom
1
35
Foam Bed
1
4
Bed Frame
1
36
Foam Grip
2
5
Pivot Arm
2
37
Protective Cover
2
6
Adjustable Lock Plate
1
38
Hex Head Bolt M8x23
2
7
Steel Heel Holder Bracket
4
39
Front Plastic Cover
1
8
Right Folding Arm
2
40L
Left Plastic Cover
1
9
Rear Rod
1
40R
Right Plastic Cover
1
10
Bolt M8x23
2
41
Square End Cap
2
11
Front Rod
1
42
Locking Pin
1
12
Phillips Screw M6x35
4
43
Hex Head Bolt M8x43
2
13
Washer Ø20xØ8.5x1.5
17
44
Height Scale
1
14
Round Plate
1
45
Latch
1
15
Lock Nut M8
12
46
Foam Bed Bolt
5
16
Lock Nut M6
6
47
Lumbar Pad
1
17
Blocking Bush Ø28.5xØ23x14
2
48
Bolt M6x20
4
18
Large Spring Knob
1
49
Right Foot Cap
2
19
Safety Hook
2
50
Left Foot Cap
2
20
Rubber Pad
1
51
Bolt M6x25
4
21
Oval End Cap
2
52
End Cap (□25x50mm)
5
22L
Left Adjustable Boom Plate
1
53
Foam Grip
2
22R
Right Adjustable Boom Plate
1
54
Washer Ø13xØ6.5x1.0
8
23
In-Step Frame
2
55
Nut Cap Ø27xØ13.5
4
24
In-Step Foot Pad
2
56
Adjustable Handle
1
25
Round End Cap
4
57
Handle Cap
1
26
Lower Bed Frame Bushing
2
58
Handle Spring
1
27
Washer Ø16xØ6.5x1.0
4
59
Button
1
28
Upper Bed Frame Bushing
1
60
Handle Tip
1
29
Handlebar
2
61
Blocking Bush Ø28.5xØ22.5x10
2
30
Knob
1
62
Screw M3x10
10
31
Rubber Heel Holder
4
63
Bolt M6x15
1
32
Nylon Strap
1
64
Carriage Bolt M8x70
2

8
PARTS LIST
No.
Description
Qty
No.
Description
Qty
65
Bolt M6x30
1
70
Bolt M5x10
2
66
Spacer Ø22x16.8
2
71
Bolt M8x 50
4
67
Screw ST4.2x12
8
72
Pivot Arm Ring
2
68
Screw ST4.8x20
1
73
Phillips head screw M4x25
1
69
Shaft Nut Ø8
1

9
HARDWARE & TOOLS PACK

10
ASSEMBLY
Step 1:
1.1 Stand up the base of the machine by separating the Front and Rear U-Frames (1, 2). Pull the
Front and Rear U-Frames (1, 2) apart from each other. Push down on the middle of the Folding
Arms (8) until the frames are fully locked down.
1.2 Attach each of the Right & Left Foot Caps (49, 50) to the Front & Rear U-Frame (1, 2) with
one Screw (48), one Screw (51), and two Washers (54). Tighten the screws using the Multi Hex
Tool with Phillips Screwdriver provided.
Hardware:
(54) Washer
8 PCS
(48) Bolt
4 PCS
(51) Bolt
4 PCS
Multi Hex Tool with Phillips
Screwdriver
Tool:
54
54
54
54

11
ASSEMBLY
Step 2:
2.1 Install a Nut Cap (55) onto the Lock Nuts (15). Slide a Protective Cover (37) on to each side
of the base as shown. Pull down on the Protective Covers (37) until the bottom of the covers are
slightly lower than the Folding Arms (8). Use the Velcro Straps on the bottom of the Protective
Covers (37) to secure the covers to the Folding Arms (8). When the covers are assembled
correctly, the Folding Arms (8) should be fully covered by the Protective Covers (37).
Step 3:
3.1 Slide the bottom of the Pivot Arms (5) into the brackets that are located on each side of the
Bed Frame (4). Align the arms with the desired hole on the arm with the peg on the bracket. Insert
the peg into the hole to lock the Pivot Arms (5) in place. It is recommended that you use the
bottom hole on the Pivot Arms (5) until you become more familiar with the equipment.
(55) Nut Cap
2 PCS

12
ASSEMBLY
Step 4:
4.1 Mount the Bed Frame (4) to the Rear U-Frame (2) by inserting the ends of the Pivot Arms (5)
into the channels on the plates. The slotted portion of the rollers on the end of the Pivot Arms (5)
should be inserted into the channels on the plates.
Step 5:
5.1 Slide the Steel Heel Holder Brackets (7) and Rubber Heel Holders (31) onto
both ends of the Rear Rod (9). Ensure the lock teeth are wedged into the slots in
Rear Rod (9) as shown in the figure above. Repeat this step to install the Steel Heel Holder
Brackets (7) and Rubber Heel Holders (31) onto the Front Rod (11).
NOTE: Make sure the lock teeth are wedged into the slots in the Rear and Front Rods (9, 11)
before use. See Figure A.
Figure A

13
ASSEMBLY
Step 6:
6.1 Pull out AND HOLD the Large Spring Knob (18) and slide the Adjustable Boom (3) into the
square bracket on the bottom of the Bed Frame (4) as shown. Slide the Adjustable Boom (3) to
the desired height.
6.2 Lock the Adjustable Boom (3) in place by releasing the Large Spring Knob (18) and sliding
the Adjustable Boom (3) up or down slightly until the Large Spring Knob (18) "POPS" down into
the locked position. Secure the Knob (30) onto the back side of the bracket on the Bed Frame (4)
as shown.

14
ASSEMBLY
Step 7:
7.1 Attach the top end of the Handlebar (29) onto the Rear U-Frame (2) and Pivot Arm Ring (72)
with one Hex Head Bolt (38), one Lock Nut (15), and two Washers (13). Attach the bottom end of
the Handlebar (29) onto the Rear U-Frame (2) with one Hex Head Bolt (43), one Lock Nut (15),
and two Washers (13). Tighten all bolts and nuts using the Multi Hex Tool with Phillips
Screwdriver, and Hex Wrench provided. Attach a Nut Cap (55) onto the Hex Head Bolt (38).
7.2 Repeat this step to attach the other Handlebar (29) on the opposite side of the Rear U-Frame
(2).
Hardware:
(15) Lock Nut
4 PCS
(13) Washer
8 PCS
(38) Hex Head Bolt
2 PCS
(43) Hex Head Bolt
4 PCS
(55) Nut Cap
2 PCS
Tool:
Multi Hex Tool with Phillips
Screwdriver
Hex Wrench

15
ASSEMBLY
Step 8:
8.1 Attach the Nylon Strap (32) to the Strap Lock (34) by inserting the end of the Nylon Strap (32)
up through the bottom of the Strap Lock (34). Loop the Nylon Strap (32) over the Pre-assembled
Loop Strap (33) and down through the Strap Lock (34). Then loop the strap back over itself, and
insert back through the Strap Lock (34), and pull tight to secure. See Diagram above.
Step 9:
9.1 Attach the Nylon and Loop Straps (32, 33) to the inversion table by hooking the end of the
Nylon Strap (32) to the loop on the back of the Bed Frame (4) as shown. Then hook the other end
of Loop Strap (33) to the other Pre-assembled loop on the Front U-Frame (1) as shown above.
32
33

16
ASSEMBLY
Step 10:
10.1 Insert the Velcro strap on the Foam Bed (35) to the Lumbar Pad (47) and secure the Lumbar
Pad (47) onto the Foam bed (35).

17
OPERATIONS & ADJUSTMENTS
WARNING: Make sure both pivot arms are in the same hole to prevent serious injury from
occurring.
Make sure the pivot arm is inserted all the way
into the slot. When the Pivot arm is aligned
correctly in the groove of the curved slot the
pivot arm will be able to move freely.
Correct
Incorrect
The slot of the Pivot arm is NOT aligned
correctly. The pivot arm must be inserted
all the way into the curved slot.

18
OPERATIONS & ADJUSTMENTS
ADJUSTING THE STRAP
A nylon strap has been included to restrict the degree of inversion. This strap can be adjusted to
different lengths to allow for a greater or lesser degree of inversion. To lengthen the Nylon Strap
(32) feed the top end of Nylon Strap (32) into the strap lock, and pull on the lower end of the strap.
To shorten the length feed the bottom end of Nylon Strap (32) into the strap lock, and pull on the
top end. See Diagram above.
ADJUSTING THE BOOM
The Adjustable Boom (3) can be moved to a variety of different positions, in order to
accommodate users of different heights. To adjust the boom loosen the Knob (30), pull out AND
HOLD the Large Spring Knob (18) and slide the boom up or down to the desired height. The
height scale is positioned just below the Square Bushing (26). When the boom is in the desired
position, release the Large Spring Knob (18). Slide the boom slightly up or down until the Large
Spring Knob (18) locks into place and tighten the Knob (30).
SHORTEN
LENGTHEN
THE STRAP