Ironwood GLACIER CDAS User manual

CDAS
CDAS39
SHELF UNIT
0708
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
AB
CD
Left Side - CDAS
Left Side - CDAS39
01010141
01010241
1 ea.
1 ea.
Top 01010101 1 ea.
Right Side - CDAS
Right Side - CDAS39
01010141
01010241
1 ea.
1 ea.
Back - CDAS
Back - CDAS39
01010152
01010252
1 ea.
1 ea.
Bottom 01010111 1 ea.
F
Toeboard 01010172 1 ea.
Adjustable Shelf 01010124 1 ea.
E G

H4 Dowel 195000 12 ea.
H3 Minifix Bolt 909834 18 ea.
H2 Leveler 300870 4 ea.
H5 MInifix Cam 909810 18 ea.
H1 Leveler Insert 274650 4 ea.
H6 Angle Bracket 401170 2 ea.
H7 Varianta Screw 988060 8 ea.
H8 Confirmat Screw 950100 3 ea.
H9 Rafix Cam 909910 6 ea.
H10 Rafix Bolt 909923 6 ea.
H12 Connector Sleeve 950200 4 ea. H13 Connector Screw 901350 4 ea.
H11 Grommet 286580 5 ea.
HARDWARE
Hardware for Connecting to Another Unit

ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

#1
#3
Insert six Minifix Cams
(H5) into the Top (C) and
Back (D) with the arrows
of the cams facing out.
H5
#2
Screw nine Minifix Bolts (H3)
and insert six Dowels (H4)
into the Left Side (A) and
Right Side (B) where
indicated.
Place the Left Side (A) and Right Side (B) on a clean carpeted surface with the pre-drilled holes
facing up. Insert the Leveler Inserts (H1) into the holes in the bottom edges of each Side. Using a
plastic mallet, tap until flush with the surface. Screw the Levelers (H2) into the Leveler Inserts.
Adjust Levelers when the assembled unit is in place.
H3
H4

Secure an Angle Bracket (H6) to each end of the Toeboard (F) using the Varianta Screws (H7).
#4
H7 H7
Insert six Minifix
Cams (H5) into the
Bottom (E) with the
arrows of the cams
facing out.
#5
Attach the Toeboard (F) to
the Bottom (E) using three
Confirmat Screws (H8)
through the pre-drilled
holes as shown.
#6
H5
NOTE: The Angle Brackets
should be oriented towards
the inside as shown.
H8

Place the Left Side (A) as
shown. Position the Top
(C) onto the Left Side.
Turn the cams (H5)
clockwise to secure.
#7
Position the Back (D)
onto the Left Side (A)
and turn cams (H5)
clockwise to secure.
#8
Position the Bottom Shelf
(E) and Toeboard (F)
assembly onto the Left
Side (A) and turn cams
(H5) to secure.
#9

Position the bolts and dowels of
the Right Side (B) onto the unit
and turn cams (H5) clockwise to
lock in place.
#10
Secure the Angle Brackets
(H6) of the Toeboard (F) to the
Left Side (A) and Right Side
(B) using Varianta Screws
(H7).
#11
H7
H7

With the assistance of another person,
turn the unit upright. Screw three Rafix
Bolts (H10) into pre-drilled holes of each
Side (A & B) at a selected height.
Position the Adjustable Shelf (G) onto
the posts as shown. Using a #3 Phillips
screwdriver, turn the rotating portions of
the cams ¼-turn clockwise to secure.
Note: Do not exceed ¼-turn when
tightening cams!
#13
H10
Insert Grommet (H11) into the Left Side (A), Right
Side (B), Top (C), Bottom (E), and the Adjustable
Shelf (G).
#14
Insert six Rafix Cams (H9) into the Adjustable Shelf (G) with the flat edge facing outwards and tap
until fully seated in place as shown.
Note: The edge of the Rafix Cam must be aligned with the shelf edge. Rafix Cams cannot be
repositioned if installed incorrectly.
#12
Your Glacier Circulation Shelved Storage Unit
is now fully assembled and ready for use.

Remove Grommets (H11) from
the panels to be connected.
CONNECTING TO OTHER
CIRCULATION DESK UNITS
Using a 13/64" bit, drill through the four
pilot holes on the inside of each side
panel.
Align the side panels of the units to be
connected. Tap four Connector Sleeves
(H12) through the holes in one side
panel and into the holes of the unit to be
connected. From the other side, secure
the units together using four Connector
Screws (H13).
H13
H12