Ironwood MH60 User manual

MH60/MH72
DESK HUTCH
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
03/07

PARTS DIAGRAM
A
Left Side – MH60
Left Side – MH72
02340141
02340141
1 ea.
1 ea.
B
C
Right Side – MH60
Right Side – MH72
02340141
02340141
1 ea.
1 ea.
Top – MH60
Top – MH72
02340141
02340141
1 ea.
1 ea.
Back – MH60
Back – MH72
02340152
02340252
1 ea.
1 ea.
D
E
Shelf – MH60
Shelf – MH72
02340127
02340227
1 ea.
1 ea.
F
Facia Strip – MH60
Facia Strip – MH72
02340186
02340286
1 ea.
1 ea.
Divider 02340144 1 ea.
G
Doors – MH60
Doors – MH72
02340174
02340274
2 ea.
2 ea.
J

195000
H7 #8x5/8
Panhead Screw 988056 40 ea.
H6 Flipper Hinge
Slide 490390 2 pr.
H9 Connector
Bracket 401200 4 ea.
H8 Door Bumper 298034 4 ea.
Attachment Tape 298530 2 ea.
Glue 295020 1 ea.
H4 Confirmat
Screw 950100 2 ea.
H3
H5
Minifix Bolt 909834 24 ea.
H1 MInifix Cam 909810 24 pr. H2 Wood Dowel 24 ea.
H10
HARDWARE

Place the Shelf (E) as
shown on a clean, carpeted
surface. Insert eight Minifix
Cams (H1) into the Shelf (E)
with the arrows of the cams
facing out.
#1
Insert eight Dowels (H2) into pre-drilled
holes of Facia Strip (F). Apply a small
amount of Glue (H5) onto the dowels of
the Facia Strip (F). Position the Facia
Strip (F) into the corresponding holes in
the Shelf (E) and press firmly into place.
Wipe away any excess glue with a damp
cloth. Set aside to dry.
NOTE: Use ten Dowels (H2) for
the MH72.
#2
The MH60 and MH72 are slightly different, but assemble
in the same way. The MH60 is shown here.
ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
H5

Place the Left Side (A) with the
pre-drilled holes facing up. Screw
seven Minifix Bolts (H3) and
insert six Dowels (H2) into the
Left Side (A) where indicated.
#5
Place the Right Side (B) with the
pre-drilled holes facing up. Screw
seven Minifix Bolts (H3) and
insert six Dowels (H2) into the
Right Side (B) where indicated.
#6
Place the Top (C) with
the cam holes upright as
shown. Insert eight
Minifix Cams (H1) into
the Top (C) with the
arrows facing out.
#3
Screw two Minifix
Bolts (H3) and insert
two Dowels (H2) into
the Top (C) where
indicated.
#4

Screw eight Minifix Bolts
(H3) into the Back (D)
where indicated.
#8
Position the Top (C) onto the
Back (D) and turn the arrows
of the Minifix Cams (H1)
clockwise to secure.
#9
Insert two Minifix Cams
(H1) into the Divider (G)
where indicated.
#10
Place the Back (D) as
shown. Insert six Minifix
Cams (H1) into the Back (D)
with the arrows of the cams
facing out.
#7

Secure the Divider (G) to the
Shelf (E) using two Confirmat
Screws (H4) as shown.
#13
Position the Shelf (E) and
Facia Strip (F) assembly onto
the bolts of Back (D) as shown
and turn the arrows of the
Minifix Cams (H1) clockwise to
secure.
#12
Position the Leftside (A) onto the
unit and turn the arrows of the
seven Minifix Cams (H1) clockwise
to secure.
#14
Position the Divider (G) onto the
bolts and dowels of the Top (C)
and turn the arrows of the Minifix
Cams (H1) clockwise to secure.
#11
A
H1
H1
H1

Position the Right Side (B)
onto the unit and turn the
arrows of the seven Minifix
Cams (H1) clockwise to
secure. Stand the unit upright.
#15
#16
NOTE: The roller end
of the Flipper Hinge
Slide should be at the
top edge of the Door.
Attach two Flipper Hinge Slides (H6) to each Door (J) using 5/8" Panhead
Screws (H7) through the indicated slots into the pre-drilled holes. NOTE: The
screws should be installed into the center of each slot as shown.
Remove the backings from
the Door Bumpers (H8) and
stick to each bottom corner
of the Doors about ½" from
the edges as shown.
#17
H1
H1
H1
J
H7
H6
H8
H8

#18
NOTE: Slide Doors toward back
before installing screws.
Attach the Doors using 5/8" Panhead
Screws (H7) through the slotted
holes of the Flipper Hinge Slides into
the pre-drilled holes in the underside
of the Top (C).
NOTE: Install the screws into the
center of the slotted hole.
Check the Doors for side-to-side alignment.
There should be approximately 1/8" space
between each door and each side, and
between both doors. If adjustment is
necessary, slightly loosen screws, reposition
the doors and retighten the screws.
#19
When the Doors are correctly
aligned, secure Hinge in place with
four additional 5/8" Panhead
Screws in the indicated holes.
#20
#21
Your Desk Hutch is now completely
assembled and ready for use.
IMPORTANT! H7
H7
H7
H7
H7
H7

ATTACHING THE HUTCH
TO A DESK UNIT
The Hutch must be carefully
centered on the desk unit
as shown.
CONNECTOR BRACKET METHOD
A. Carefully position the hutch onto the desktop as
described in hutch location instructions (above).
B. With the hutch and desk aligned, position two
Connector Brackets (H9) on each Side Panel (A & B) in
the indicated locations. Mark the locations of the pilot
holes with a pencil.
C. Using an electric drill and a 1/8" bit, drill the pilot
holes 1/2" deep.
NOTE: Be careful not to drill all the way through the
side panels.
D. Secure the hutch sides to the
desktop using the 5/8" Panhead
Screws (H7) through the four
Connector Brackets.
TAPE METHOD
A. Carefully position the hutch onto the desktop as
described in hutch location instructions (above).
B. Use a pencil to mark the location of the front, back
and outside edges of the hutch sides onto the desktop.
C. With the assistance of another person, lift the hutch
off the desk. Lay the hutch down on its back. Remove
backing from one side of each Tape Strip (H10) and
place on the bottom edges of the Left Side (A) and the
Right Side (B).
D. Remove the backing from other side of each Tape
Strip. With the assistance of another person, very
carefully align the hutch onto the pencil markings of
the desktop. When aligned, place the hutch on the
desk unit.
IMPORTANT! It will be difficult to
remove or reposition the units
once joined.
H10
H10
H9
H7
H7