Ironwood GLACIER CDTW32 User manual

CIRCULATION DESK
CDTW32
CDTW39
TOWER STATION
0307
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
A
B
Left Side - CDTW
Left Side - CDTW39
01050641
01050741
1 ea.
1 ea.
C
D
E
Back - CDTW
Back - CDTW39
01050652
01050752
1 ea.
1 ea.
F
K
P
Keyboard Shelf 01050641 1 ea.
Right Side - CDTW
Right Side - CDTW39
01050641
01050741
1 ea.
1 ea.
Top 01050601 1 ea.
Bottom 01050611 1 ea.
Printer Shelf 01050629 1 ea.
J
Divider 01050644 1 ea.
Toeboard 01050172 1 ea.

S1 Full Extension
Slide 490420 2 ea.
H4 Dowel 195000 14 ea.
H5 Minifix Bolt 909834 20 ea.
H3 Leveler 300870 4 ea.
H7 Angle Bracket 401170 2 ea.
H2 Leveler Insert 274650 4 ea.
H9 #8 x 5/8"
Panhead Screw 988056 12 ea.
H1 Minifix Cam 909810 20 ea.
H8 Confirmat Screw 950100 3 ea.
H6 Varianta Screw 988060 16 ea.
H11 Connector Screw 901350 4 ea.
H10 Grommet 286580 4 ea.
H12 Connector Sleeve 950200 4 ea.
HARDWARE
Wire Trough 412990 1 ea.
H13
H14 6 x .625 Panhead
Screw 901216 2 ea.

ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
Insert six Minifix Cams (H1) into the
Back (D) with the arrows of the cams
facing out.
#1
#2
H1
Place the Left Side (A) and Right Side (B) on a clean,
carpeted surface with the pre-drilled holes facing up. Insert
the Leveler Inserts (H2) into the holes in the bottom edges of
each Side. Using a plastic mallet, tap until flush with the
surface. Screw the Levelers (H3) into the Leveler Inserts.
Adjust Levelers when the assembled unit is in place.

#3
#4
H5
H4
Screw nine Minifix Bolts (H5)
each and insert six Dowels (H4)
each into the Left Side (A) and
Right Side (B) where indicated.
Attach two Full Extension Slides (S1) to Left Side
(A) using four Varianta Screws (H6) as shown.
Note: It will be necessary to slide the sliding
portion forward to access the 1st hole.
H6
LOCKING
CLIP ARM
CHANNEL
SECTION
MAIN PORTION
OF SLIDE
LOCKING
CLIP ARM
You must disassemble the Full
Extension Slides before installing
them on the Side Panels (A & B) and
the Divider (J). The Full Extension
Slides (S1) consist of the main slide
sections and the channel sections.
To disassemble the slide, extend the
slide completely. Push the arm of the
locking clip up and pull the channel
section forward until disconnected as
shown.
Set the four channel sections aside
until Step #19.

#5
H6
Attach a Full Extension Slide (S1) to Right Side
(B) using two Varianta Screws (H6) as shown.
Note: It will be necessary to slide the sliding
portion forward to access the 1st hole.
#6
#7
Position Back (D) onto the Left Side (A) as shown
and turn the cams (H1) clockwise to secure.
Insert six Minifix Cams (H1) into the Top (C) with
the arrows of the cams facing out.
H1

#8
H13
20"
H14
H13
Peel the paper backing off of the adhesive strip on the Wire
Trough (H13). Attach the Wire Trough to the Back of the unit and
secure in place by driving two Panhead Screws (H14) through
the predrilled holes in the Wire Trough.
Position Top (C) onto the Left Side (A) as shown and turn the
cams (H1) clockwise to secure.
Note: It will be difficult to remove or reposition the wire trough
once the Back and Top are joined.
#9
#10
Position Bottom (E) with the underside side facing
up as shown. Insert six Minifix Cams (H1) into the
Bottom (E) with the arrows of the cams facing out.
H1
Flip Bottom (E) over so that the top surface is
showing. Screw two Minifix Bolts (H5) and insert
two Dowels (H4) in Bottom where indicated.
H5
H4

#11
Secure an Angle Bracket (H7) to each end
of the Toeboard (F) using four Varianta
Screws (H6).
H6
H6
#12
#13
H8
Insert two Minifix Cams (H1) into the Divider
(J) with the arrows of the cams facing out.
H1
Attach the Toeboard (F) to the Bottom
(E) using three Confirmat Screws
(H8) through the pre-drilled holes as
shown.
Note: The Angle Brackets (H7)
should be oriented as shown.

#14
H6
Attach a Full Extension Slide
(S1) to Divider (J) using two
Varianta Screws (H6) as
shown.
Note: It will be necessary to
slide the sliding portion
forward to access the 1st
hole.
#15
#16
Position bottom assembly onto the Left Side (A)
and turn the cams (H1) clockwise to secure.
Position Divider (J) onto the topside of Bottom (E) with
front edges aligned as shown and turn the cams (H1)
clockwise to secure.

#17 Position the bolts and dowels of the Right
Side (B) onto the unit and turn cams (H1)
clockwise to lock in place.
#18
#19
Secure the Angle Brackets (H7) of the
Toeboard (F) to the Left Side (A) and
Right Side (B) using four Varianta
Screws (H6).
With the assistance of another person,
turn the unit upright.
H6
H6
H7
H7
H9
H9
Attach two channel portions of the Full
Extension Slides (S1) to the right and left side
of the Keyboard Shelf (K) using six #8 x 5/8"
Panhead Screws (H9) as shown.
Note: Make sure that the notch of locking clip
is oriented as shown in diagram for proper
slide function.

#21
#22
Extend cabinet portions of the Full Extension
Slides completely out.
Slide the channels of the Keyboard Shelf (K) and
Printer Shelf (P) onto the slides of the cabinet as
shown until secured by the locking clips.
H9
#20
H10
Insert a Grommet (H10) into the Left Side (A),
Right Side (B), Top (C), and Bottom (E).
Your Glacier Circulation Desk is now fully
assembled and ready for use.
Attach the two remaining channel portions of the
Full Extension Slides (S1) to the right and left
side of the Printer Shelf (P) using six #8 x 5/8"
Panhead Screws (H9) as shown.
Note: Make sure that the notch of locking clip
is oriented as shown in diagram for proper slide
function.

CONNECTING OTHER WORKSTATIONS:
Remove Grommets from the panels to be
connected.
Using a 13/64" bit, drill through the
four pilot holes on the inside of each
side panel.
Align the side panels of the units to be
connected. Tap four Connector
Sleeves (H11) through the holes in
one side panel and into the holes of
the unit to be connected. From the
other side, secure the units together
using four Connector Screws (H12).
H12
H11