Ironwood GLACIER CDCUR User manual

CDCUR
CDCRR
RISER UNIT
0820
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

A
PARTS DIAGRAM
B
C
D
M
Left Side 01011642 1 ea.
N
Top CDCUR
Top CDCRR
01050801
01050501
1 ea.
1 ea.
Right Side 01011643 1 ea.
Right Back CDCUR
Right Back CDCRR
01050854
01050554
1 ea.
1 ea.
Left Back CDCUR
Left Back CDCRR
01050854
01050554
1 ea.
1 ea.
Back CDCUR
Back CDCRR
01050852
01050552
1 ea.
1 ea.

H2 Rafix Bolt 909923 25 ea.
H3 Flush Rafix Cam 909911 8 ea.
HARDWARE
H1 Rafix Cam 909909 4 ea.
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned
H4 Double-Sided
Tape 298525 6 ft

Insert four Rafix Cams (H1) and
screw four Rafix Bolts (H2) into the
Top Panel (C) as shown.
#1
c
H1
H2
H1
TOP
A
B
H2
H2
LEFT SIDE
RIGHT SIDE
#2
Screw four Rafix Bolts (H2) into
each Side Panel (A & B) as shown.

#3
#4
D
C
H3
H3
M
H3
H3
LEFT BACK
ND
H3
H3
H3
RIGHT BACKBACK
H3
Insert Flush Rafix Cams
(H3) into each Back
Panel (M,N,D) as shown,
making sure the arrow
faces out toward the edge
of the panel.
Attach the Back Panel (D)
to the Top (C) as shown.
Turn the Flush Rafix
Cams (H3) clockwise to
tighten.
#5
D
C
M
H3
Attach the Left Back (M)
as shown. Turn the
Flush Rafix Cam (H3)
clockwise to tighten.

H3
N
Attach the Right Back (N) as shown. Turn the Flush Rafix Cam (H3) clockwise to
tighten.
#6
H3
H1
A
Attach the Left Side as shown.
Turn the Rafix Cams(H1) and
Flush Rafix Cams (H3)
clockwise to tighten.
#7

Attach the Right Side (B)
as shown. Turn the Rafix
Cams (H1) and Flush
Rafix Cams (H3)
clockwise to tighten.
#8
BH3
H1
#9
CDCU or CDCR
Attach with Double-Sided Tape
Attach with double-
sided tape (H4)
The installation of your Glacier Corner Riser unit
is now complete and ready to use.
ATTACHING THE UNIT TO THE DESKTOP: