Ironwood GLACIER PBS42SB User manual

01/05
BY
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
PICTURE BOOK
SHELVING
PBS42SB
PBS48SB
SINGLE BASE UNIT

PARTS & HARDWARE
A
B
C
D
Right Side - PBS42SB
Right Side - PBS48SB
01020141
01020341
1 ea.
1 ea.
Left Side - PBS42SB
Left Side - PBS48SB
01020141
01020341
1 ea.
1 ea.
Top 01020102 1 ea.
Shelves 01024724 2 ea.
3 ea.
PBS42SB
PBS48SB
2 ea.
3 ea.
412226
H2 Book Stop - PBS42
Book Stop - PBS48
20 ea.
25 ea.
988056
H3 Panhead Screw - PBS42
Panhead Screw- PBS48
H5 Varianta Bolt 988060 8 ea.
H8 Wire Dividers - PBS42
Wire Dividers - PBS48 412026 8 ea.
12 ea.
H6 Metal Frame 412026 1 ea.
4 ea.
8 ea.
909932
H7 Tab-V Shelf Pin - PBS42
Tab-V Shelf Pin - PBS48
12 ea.
16 ea.
909930
H1 Tab-V Plastic Housing - PBS42
Tab-V Plastic Housing - PBS48
H4 Tab-V Metal
Flange 909931 8 ea.

it is important to read all the way through the Adder instructions
(enclosed in the Adder carton) before beginning. It will be necessary to
substitute a Divider (J) for a Right Side (B) during assembly.
NOTE:
The diagrams show one size for ease of viewing.
Any differences will be indicated in each step
’ s text.
If you have purchased an Adder unit
to be assembled in conjunction with this Base unit,
it is important to read through the Back option
and/or Toe Space option directions before beginning.
If you have purchased the Back option or the Toe Space option
to be assembled in conjunction with this Base unit,

Using a plastic mallet, tap in the
plastic housings with the flat
edge facing outwards until flush
with the surface.
IMPORTANT! The flat
edge of the plastic
housing must be
aligned with the shelf
edge. Plastic Housings
cannot be repositioned
once installed.
For a Fixed Shelf or Top,
install the metal flange using a
System (Varianta) Screw as
shown. DO NOT over tighten!
For an Adjustable Shelf, use
the Metal Shelf Clip.
Slide the shelf into place over
the Metal Flanges and push
down until fully seated.
Turn the rotating portion (Cam)
1/2 turn to lock in place.
To remove, simply turn the
Cam counter clockwise 1/2
turn and lift the shelf off of the
Metal Flanges.
ALIGNED
FLAT
EDGE
USING THE TAB-V SYSTEM:
ADJUSTABLE
FIXED

#1
#2
Insert four Tab-V Plastic Housings (H1) into the Top (C) so that the flat edge is
facing outwards. Using a plastic mallet, tap the housings until flush with the surface.
The flat edge of the plastic housing must be aligned with shelf edge. Plastic
housings cannot be repositioned
once installed.
Insert four Tab-V Plastic Housings (H1) into the all of the
shelves (D) and install as in Step #1.
H2
H3
E
H1
H1
H1 H1
C
H1
H1 H3
H2
#3
Attach a Book Stop (H2) to the Fixed
Shelf (D) using five Panhead Screws
(H3) in the pre-drilled holes.
Place both Side Panels (A & B) on a clean, carpeted surface as shown. Install Tab-V metal
Flanges (H4), using Varianta Screws (H5). Refer to “Using the Tab-V System” on the 4th page
of these instructions.
Use the top set of
pre-drilled holes,
and the fourth set
above the bottom
of pre-drilled holes
for the metal
flanges.
D
Refer to “Using the Tab-V System” on the 4th page of these instructions.
A
B
FRONT
FRONT
H4 - H5
H4 - H5
H4 H5

A
H3
FRONT
TOP
#4 #5
Place the Right Side Panel (B) on a clean,
carpeted surface as shown. Attach the
Metal Frame (H6) on the back edge of the
panel using five Panhead Screws (H3)
screwed into the pre-drilled holes on the
Side Panel.
With the assistance of another person,
set the Panel and Frame assembly
upright and install the Left Side Panel
(A) to the other side of the Metal Frame,
using five Panhead Screws (H3)
screwed into the pre-drilled holes on the
Side Panel.
A
B
H3
#6
B
A
C
D
Slide the Top (C) onto the Tab-V Metal
Flanges (H4) previously installed into the
top set of holes on the Side Panels. Press
the Top down until the Plastic Housings
(H1) are securely seated onto the Metal
Flanges. Turn the rotating portion (plastic
housing) 1/2 turn to lock in place.
Install a Shelf (D) onto the bottom set of
Metal Flanges in the same way.

Chose the height for the remaining
Shelves (D).
42” Unit: Midway is recommended for the
single remaining shelf.
48” Unit: Placement of the two remaining
shelves must allow for the installation of
the Wire Dividers.
Insert Tab-V Shelf Pins into the holes
corresponding to your chosen shelf
heights.
Slide the shelves onto the Tab-V Pins and
press down until firmly seated.
#7
#8
Your Glacier Picture Book Shelving unit is now fully assembled and ready for use.
Insert the Wire Dividers (H8) into the
pre-drilled holes of the upper surface
of the shelves.
FINISHED
EDGE
H7
H7