Ironwood GLACIER CD3629 User manual

CIRCULATION DESK
CD3629/CD3632
CD3639
DESK SHELL
0720
BY
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You will need a Phillips head screwdriver,
a medium slotted screwdriver and a plastic mallet.
To protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

PARTS DIAGRAM
Left Side – CD3629
Left Side – CD3632
Left Side – CD3639
01011941
01012041
01012141
1 ea.
1 ea.
1 ea.
A
Right Side – CD3629
Right Side – CD3632
Right Side – CD3639
01011941
01012041
01012141
1 ea.
1 ea.
1 ea.
B
Top 01011901 1 ea.
C
Bottom 01010511 1 ea.
E
Toeboard 01010172 1 ea.
F
D
Back – CD3629
Back – CD3632
Back – CD3639
01011952
01012052
01012152
1 ea.
1 ea.
1 ea.

H8 Confirmat Screw 950100 3 ea.
H5 Wood Dowel 195000 12 ea.
H4 Rafix Bolt 909923 14 ea.
H6 Angle Bracket 401172 2 ea.
H7 #14 x1/2"
Panhead Screw 901233 8 ea.
H10 Connector Sleeve 950200 4 ea.
H13 Panhead Screw 901216 2 ea.
H11 Connector Screw 901350 4 ea.
H12 Wire Trough 412990 1 ea.
H2 Leveler Insert 274650 4 ea.
H3 Leveler 300870 4 ea.
H1 Rafix Cam 909910 14 ea.
H9 Grommet 286580 3 ea.
HARDWARE

Place the Top (C) and
Back (D) onto a clean,
carpeted surface with the
pre-drilled holes facing
up. Insert six Rafix Cams
(H1) into each panel with
the arrows of the cams
facing out.
#1
Insert the Leveler Inserts
(H2) into the holes in the
bottom edges of Left Side
(A) and Right Side (B).
Using a plastic mallet, tap
until flush with the surface.
Screw the Levelers (H3)
into the Leveler Inserts.
Adjust Levelers when the
assembled unit is in place.
#2
H1
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

Screw seven Rafix
Bolts (H4) into the
Sides (A & B) where
indicated.
Insert six Dowels
(H5) into the Sides
where indicated.
#3
Secure an Angle Bracket (H6)
to each end of the Toeboard
(F) using the ½" Panhead
Screws (H7).
#4
Attach the Toeboard (F) to the
Bottom (E) using three
Confirmat Screws (H8) through
the pre-drilled holes as shown.
#5
Note: The Angle
Brackets should be
oriented towards the
inside as shown.
H8
H5
H4
H7
H7

Insert two Rafix Cams (H1)
into the Bottom (E)
#6
Place the Left Side (A) with
the bolts and dowels facing
up as shown. Position the
Top (C) onto the Left Side
and turn cams (H1)
clockwise to secure.
#7
Position the Back (D)
onto the Left Side (A)
and turn the cams (H1)
clockwise to secure.
#8
H1

Position the Bottom (E)
and Toeboard (F)
assembly onto the Left
Side (A) and turn cam
(H1) clockwise to secure.
#9
Position the bolts and
dowels of the Right Side
(B) onto the unit and turn
the cams (H1) clockwise
to lock in place.
#10
Secure the Angle
Brackets (H6) of the
Toeboard (F) to each
Side (A & B) using ½"
Panhead Screws (H7).
#11

#12
#13
H12
19"
FROM
BOTTOM
PANEL
H9
H13
Peel the paper backing from the adhesive strip on
the Wire Trough (H12). Attach the Wire Trough to
the Back of the unit and secure in place by driving
two Panhead Screws (H13) through the predrilled
holes in the Wire Trough.
With the assistance of another
person, turn the unit upright. Insert
Grommets (H9) into the Left Side
(A), Right Side (B), and Top (C).
Your Glacier Desk Shell is now
fully assembled and ready for
use.

Remove Grommets
from the panels to be
connected.
Using a 13/64" bit, drill
through the four pilot
holes on the inside of
each side panel.
Align the side panels of
the units to be
connected. Tap four
Connector Sleeves
(H10) through the holes
in one side panel and
into the holes of the unit
to be connected. From
the other side, secure
the units together using
four Connector Screws
(H11).
ADJOINING TO OTHER
WORKSTATIONS:
H10
H11