Ironwood Glacier CDBC User manual

CDBC
CIRCULATION
BOOK CART
0109
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
A
D
Front Panel 01010980 1 ea.
Bottom Panel 01010911 1 ea.
B
Back Panel 01010952 1 ea.
E
Bookdrop Back 412400 1 ea.
C
Side Panel 01010941 2 ea.

H3 Swivel Caster 402640 4 ea.
H2 Nylok Nut 904420 16 ea.
H6 Wood Dowels 195000 8 ea.
H5 Minifix 909810 22 ea.
H4 Minifix Bolt 909834 22 ea.
H1 Machine Screw 902201 16 ea.
H11 Button Snap 930050 16 ea.
H7 Panhead Screw 901227 8 ea.
H8 Barrel Nut Lock 902200 3 ea.
H10 Machine Screw 901303 3 ea.
H9 Pull Handle 490670 1 ea.
HARDWARE

ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
Turn the Bottom Panel (D)
onto its side with the front
edge facing up.
Insert Long Machine Screws
(H1) through the Bottom
Panel (D) and attach four
Casters (H3) as shown.
Using a slotted screwdriver
and a 7/16" wrench, secure
in place using the Nylok Nuts
(H2) as shown.
#1
H3
H3
H3
H3
H1
H2

Turn the Bottom Panel (D) top side
up. Using a screwdriver, screw ten
Minifix Bolts (H4) into the Bottom
Panel where indicated.
#2
H4
H4
H4
#3
Screw six Minifix Bolts
(H4) and insert four Wood
Dowels (H6) into the Front
and Back Panels (A&B)
where indicated.
Insert three Minifix Cams
(H5) into the holes as
shown with the arrow
facing out.
H6
H6
H5
H4
H4
A &B
H4
H6
H5
#4
Insert eight Minifix Cams (H5)
into a Side Panel (C) facing out.
Position the Side Panel onto the
bolts and dowels of the Back
Panel (B) and turn cams
clockwise to lock in place.
H5
H5 B
C
H5

Position the Front Panel (A)
onto the Side Panels (C) and
turn cams to secure.
#6
A
B
C
C
Insert eight Minifix Cams (H5) into a
Side Panel (C) facing out. Position the
Side Panel onto the bolts and dowels
of the Back Panel (B) and turn cams
clockwise to lock in place.
#5
H5
H5
C
C
B
H5
With the assistance of another
person, carefully position the
assembly on the bolts of the
Bottom Panel (D) and turn
cams to secure.
#7
A
B
C
C
D

Insert three Barrel Nuts (H8)
into the back side of Front
Panel (A) and attach the Pull
Handle (H9) to the Front Panel
using three Short Machine
Screws (H10) as shown.
#9
From the hardware included with the Book Drop
Bag*, take four Corner Clips and attach to each
corner of unit using 1” Panhead Screws (H7) in the
predrilled holes.
*Note: Some of the hardware included with the
Book Drop Bag will not be used in this assembly.
#8
Screw sixteen Button Snap
Studs (H11) (four to each
edge) into the pre-drilled holes
in the upper edge of unit.
#10
CORNER CLIP

Press the Book Drop Bag (E) snaps onto
the Button snap Studs (H11) along the top
edges of the unit.
#12
Insert the Book Drop Bag (E) into
unit. Pull the S-hooks out of the
corners of the Book Drop Bag
and attach to the corresponding
Corner Clips (H12). Using pliers,
crimp the S-hooks onto the
Corner Clips.
#11
Your Glacier Circulation Book Cart is now fully assembled
and ready for use.