Ironwood Glacier LC36 User manual

0920
LC36
LIBRARY CARREL
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
A B
C
E
D
Left Side 01012941 1 ea. Right Side 01012941 1 ea.
Top 01012901 1 ea.
Back 01012952 1 ea.
Shelf 01012921 1 ea.

H8 Rafix Bolt 909925 20 ea.
H10 6 X .625
Panhead Screw 901216 2 ea.
H5 Leveler 300870 4 ea.
H2 Rafix Cam 909909 12 ea.
H9 Wire Trough 412990 1 ea.
H3 Leveler Insert 274650 4 ea. H4 Leveler Bracket 402302 4 ea.
H1 Flush Rafix
Cam 909911 8 ea.
H11 Grommet 286580 3 ea.
HARDWARE

ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

Place the Back (D) onto a clean, carpeted surface
with the pre-drilled holes facing up. Insert eight
Flush Rafix Cams (H1) into the Back.
#1
Insert eight Rafix Cams (H2) into the Top (C) with the flat edge of the cams aligned with the edge of
the panel.
Insert four Rafix Cams into the Shelf (E) with the flat edge of the cams aligned with the edge of the
panel.
#2
H1
H8
#3
Insert two Rafix Bolts (H8) into the predrilled holes at the top
of the Back where indicated.
Choose your desired height for the Top (C) Panel and screw
two Rafix Cams (H8) into the predrilled holes on the Back (D).

Install Leveler Inserts (H3) into the
bottom holes of the Left Side (A) and
Right Side (B) and tap until flush with
the surface. Press a Leveler Bracket
(H4) over each Leveler Insert. Screw
the Levelers (H5) into the Leveler
Inserts.
Adjust the Levelers after assembly
is complete.
#4
#5
Screw 5 rafix Bolts (H8)
into the Left and Right
Sides (A & B) where
indicated.
H8
H8
The height of the Top
(C) is optional. Select
the height that suits your
needs. Screw three
Rafix Bolts (H8) into the
appropriate set of pre-
drilled holes in the Side
Panels (A & B) where
indicated.
#6

With the help of an assistant, position the Left Side
(A) with the front and top edge as shown. Now
position the Back (D) with the Top edge as shown
onto the bolts. Tighten cams to secure.
Position the Right Side (B) onto the unit and
tighten cams to secure.
#7
With the assistance of another
person, turn the unit upright.
Position Top (C) onto the Rafix Bolts
(H8) on Left Side (A) and Right Side
(B) and on the Back (D). Using a #3
Phillips screwdriver, turn the rotating
portions of the Rafix Cams (H2) ¼
turn clockwise to secure.
Note: Do not exceed ¼ turn when
tightening!
#8
#9

Insert Grommets (H11) into the Left Side (A), Right
Side (B) and the Top (C).
Your Glacier Library Carrel is now
assembled and ready for use as a stand-alone
If a Library Carrel Adder (LC36A) is to be attached to this Base unit, do not install Side A
or Side B, depending upon which side the Adder is to be attached. For example, if a
Library Carrel Adder is to be attached to the left side of the Carrel Base unit (LC36), then
do not complete any of the steps for Side A.
See Assembly Instructions that are provided with your Library Carrel Adder unit.
#10
#11
7”
H11
H9 H10
H11
H9
H11
H11
Peel the paper backing from the adhesive strip on the
Wire Trough (H9). Attach the Wire Trough to the Back of
the unit and secure in place by driving two Panhead
Screws (H10) through the predrilled holes in the Wire
Trough.
Note: It will be difficult to remove or reposition the wire
trough once the Back and Top are joined.