Ironwood DMS User manual

0820
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
DMS
DELUXE
MACHINE STAND

Shelf 05850924 1 ea.
Right Door 05850974 1
ea.
Drawer
Bottom 191665 1 ea.
Bottom 0585091 1 ea.
PARTS DIAGRAM
AB
Left Side 1 ea.
I
D
C
L
D1 D5
D2
F
E
G
AB
I
J
G
D
C
L
D1 D5
D2
F
E
G
AB
I
J
E
C
D
Drawer
Front 05850963 1 ea.
Left Door 05850974 1 ea.
05850941 Right Side 1 ea.
05850941
Top 1 ea.
0585091
Back 1 ea.
05850952
D2
Drawer End 068070 2 ea.
D
C
L
D1
D5
D2
F
E
G
AB
I
J
D
C
L
D1
D5
D2
F
E
G
AB
I
J
Drawer Side 068270 2 ea.

H6 Hinge Plate 400201 4 ea.
H2 Plate Caster 4020501 2 ea.
H1 Large Panead
Screw 988056 16 ea.
H7 Varianta Screw 988060 6 ea.
H3 Plate Caster
W/ Lock 402051 2 ea.
H11 Rafix Bolt 909924 14 ea.
H10 Rafix Cam 909909 4 ea.
H13 Bumper
Stick-ons 298032 2 ea.
H12 Hinge 400200 4 ea.
H15 1" Washerhead
Screw 920200 6 ea.
H14 Drawer/Door
Pull 400870 3 ea.
H4 Flush Rafix
Cam 909911 10 ea.
H5 Rafix Shelf Cam 909912 4 ea.
H8 Shelf Pin 909924 4ea.

S2 18” Slide 490296 2 ea.
S1 18” Slide 490296 2 ea.
H17 Confirmat
Screw 950100 8 ea.
H19
1-1/2"
Washerhead
Screw
920202 2 ea.
H20 Phillips
Flathead Screw 901119 6 ea.
H16 Glue 295020 1 ea.

#1
H11
H11
H11
AB
Screw 5 Rafix Bolts(H11) into the pre-drilled holes of Left Side (A) and seven Rafix Bolts
into the pre-drilled holes of Right Side (B) where indicated.
H11

CLCL
#2
H6
A
H6
F
R
O
N
T
F
R
O
N
T
B
#3
B
A
FRONT
FRONT
2ND HOLE
FROM BACK
5TH HOLE
FROM FRONT
2ND HOLE
FROM FRONT
2ND HOLE
FROM BACK
5TH HOLE
FROM FRONT
2ND HOLE
FROM FRONT
H7 H7
Attach a right 18" Side Channel (S1) to the
Right Side (B) using Varianta Screws (H7) in
the upper set of pre-drilled holes as shown.
Attach a left 18" Side Channel (S1) to the
Left Side (A) using Varianta Screws (H7) in
the upper set of pre-drilled holes as shown.
S1
H7
SLOT
FRONT EDGE
OF PANEL
LARGE
HOLE
H6
Right Side
Left Side
Attach two Hinge Plates (H6) to the Left Side (A) and two Hinge Plates to the Right Side (B) using
attached screws into the pre-drilled holes as shown.
IMPORTANT! The large hole and slots must be oriented to the rear edge of the Hinge Plates
as shown.

D
A
C
H4
H4
D
A
H4
Insert six Flush Rafix Cams (H4 into the Back
(D) facing out and 2 Flush Rafix cams (H4) in
the the bottom two cam holes in both sides.
Position Back onto Left Side (A) as shown
and secure cams
#4
Insert four Rafix Cams (H10) into the Top
(C) facing out. Position Top onto Left Side
(A) as shown and rotate Cams to secure.
#5
H4
H10

D
C
A
Position the Right Side (B) Rafix Bolts into
the corresponding Cams of the unit as
shown.
#6
Insert 4 Rafix Bolts into Bottom (E)
Position and secure.
#7
B
E
D
C
A
#8
Attach four Plate casters (H2 and H3) to
the Bottom Panel (E) using the Panhead
Screws in the pre-drilled holes as shown.
(H1)
H1
H2
H3

G
H5
H5
H5
H5
Insert four Rafix Shelf Cams (H5) into the Shelf (G) facing outwards and tap until fully seated in
place as shown.
IMPORTANT! The edge of the Rafix Cam must be aligned with the shelf edge. Rafix Cams are
difficult to reposition if installed incorrectly.
#9
H5
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

#11
H13H13
IJ
H12 H12
G
Place 4 Shelf Pins (H8) into pre-drilled holes of
each Side (A and B) at a selected height.
#10
Using a Plastic Mallet, insert the Hinges (H12) to the Left and Right Doors (I and
J) as shown.
Remove backings and press Door Bumpers (H13) onto the opposite corners of
Doors where indicated.
H8
H13

#12
IJ
H14
H15
DOOR
SIDE
SLOT
RELEASE
BUTTON
To attach the Doors (I and J) to the unit, slide the slots of the Hinges (H12) onto the Hinge
Plates (H6) until the release buttons click into place.
Adjust Doors (I and J) to open and close easily by loosening hinge screws and repositioning
Hinge as shown. Tighten hinge screws when proper alignment is achieved.
#13
UP &
DOWN
SIDE TO
SIDE
IN &
OUT
Spread a thin layer of Glue (H16) on one edge of each Drawer End (D2) as shown.
Use four Phillips Head Screws (H17) to attach Drawer Ends (D2) to a Drawer Side (D1) with the
grooves aligned on the inside as shown.
#14
D2
D2
D1
H17
H16
Attach a Drawer Pull (H14) to each Door ( I and
J) using 1" Washerhead Screws (H15) as shown.
H14
H15

D2
D2
D1
D5
D1
H16
H17
Apply glue to the exposed edge of the
Drawer Bottom (D5) and Drawer Ends
(D2). Position the other Drawer Side
(D1) onto unit with the groove aligned
with the edge of the bottom.
#16#15
D5
D1
D2
D2
H16
#17
L
H14
H15
H19
Attach the Drawer Front (L) to the Drawer
assembly using two Washerhead Screws (H18)
as shown.
Attach a Drawer Pull (H15) to the Drawer Front
(L) as shown using two 1-1/2" Washerhead
Screws (H19).
Spread a thin layer of glue on both end
edges and one side edge of Drawer Bottom
(D5).
Slide the Drawer Bottom (D5) into grooves
of the Drawer Ends (D2) until seated into
the Drawer Side (D1) groove as shown. Secure Drawer Side (D1) to the Drawer Ends (D2)
using the Allen Head Screws (H17) as shown.
H15 H19

Slide the drawer assembly onto the Side Channels (S2) of the unit as shown.
#18
#19
H20
Attach the left Shelf Slide (S2) to the Drawer
unit using the Flathead Screws (H20) in the
indicated holes as shown.
Attach the right Shelf Slide (S2) to the Drawer
unit using the Flathead Screws (H20) in the
indicated holes as shown.
NOTE: Position the Slides with the flanges up and the rollers to the back as shown.
H20
S2

#20
LEVEL
EQUAL SPACING
DRAWER FRONT
AND DOORS
ALIGNED W/SIDES
H15
H15
With the drawer in place, check to insure that the Drawer Front (L) is aligned level and with equal
spacing at the edges.
If the Drawer Front needs adjustment, loosen Washer Head Screws (H15) slightly, move Drawer
Front to the correct [position and retighten screws.
Your Deluxe Machine Stand is now assembled and ready to use.
H15