ItsImagical ECO AIR ENGINE CAR User manual

ECO AIR ENGINE CAR

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
CM
Air tube
Pump Cylinder
Permanent Marker
Ruler
Product Introduction
Tools You May Need
Mechanical Parts List
Tapping Screw Tapping Screw Round Shaft Round Shaft
120
QTY
6
QTY QTY
1
QTY
P1 P2 P3 P4
Diagonal Cutter Scissors
Screwdriver
Gasoline is currently the fuel of choice, but petroleum used to make it is becoming increasingly difficult
to find and is contributing to environmental issues and worldwide problems. Automobile manufacturers
know this and are spending tremendous amounts of money to develop alternative fuel for the future. Let
us introduce you another alternative fuel and eco-friendly vehicle - Air Power Engine Car.
Air as fuel…could possibly be another alternative to petroleum. Air is available 24/7, does not run out and
it’s free. By golly, we might have something here and Air Power Engine Car can break down this
technology to its simplest form. This is an amazing kit that uses the vision of our ancestors back in the
middle of the 19th century. Now, your child can bring that vision to life and gain valuable insight into
propulsion via compressed air.
Assembly and operation is a breeze. A pump-up bar with a pressure meter is built into the car for easy
operation. This meter measures the volume of compressed air. The air chamber made from PET
(polyethylene terephthalate). The silicon tube (red in color) creates an air tight fit. Another safety device
implemented into the kit is a safety valve. If the user keeps pumping while the tank is full, the safety valve
will open and bleed the air automatically. Anyway, back to the air in the tank. When the air chamber is
full, you can release the compressed air; the air then expands and drives the vehicle a distance up to 50
meters in 35 seconds. The car is fast and furious fun that requires no batteries or specific weather
conditions to limit its usage. Air Power Engine Car is not only designed with the environment in mind,
but is also fun and easy to build!
Product contains functional edges and sharp points.
AIR POWER ENGINE CAR
1
Hammer
Tissue Paper

QTY
1 1
Sponge
QTYQTY
1
QTY
1
QTY
2
QTY
7
QTY
11
QTY
2
1
QTY
QTY
P14 P15
P20
P11 P12 P13
QTY
1
QTY
1
P17 P18
P19
2
Hex Shaft (Short) Hex Shaft (Long)Round Shaft
P8 P9 P10
P5 P6 P7
2
QTY
1
QTY
1
QTY
PET Bottle
Oil BagBottle Top
Red Cap (Medium) Red Cap (Big) Spacer
Spring O-ring (Black) Red Cap (Small)
1
QTY
P16
Silicon Tube
Sticker
Do not touch the oil while
fitting the silicon tube.
(Spare part : 1 pc)(Spare part : 1 pc)
Spare parts
IgnoreIgnore
(Spare part : 1 pc)
Valve (Clear Blue)

4
burr
burr burr
Tip : Cut Off The Burrs Before Assembly
How To Fit Air Tube
Tilt the tube
Tube
12
Measuring & Marking Cutting
How To Cut Air Tube
P15
Follow the steps above, cut the air
tubes when they are required.
Do not cut them in advance.

Plastic Parts
3
Cut the plastic parts when they are required.
Do not cut them in advance.
C
1 2
3 4
5
MADE IN TAIWAN
6
1
2 3
4
5
7
6
8 9
10
2019
18
17
16
15
14 13
12
11
D
MADE IN TAIWAN
Ignore
122
4
3
4
5
A
MADE IN TAIWAN
16
OIL B7
B
8
10
9
9
3
2
4 5
13
10
12
11
MADE IN TAIWAN
14
MADE IN TAIWAN
1
2
333
E
Ignore

Tube Module A Assembly
5
1
2
Prepare air tube before assembly.
1:1
Scale
2
A2
A2
A4
11cm
11 cm

9 cm
6
2
A5
Prepare air tube before assembly.
2
9cm
9cm 9cm
9cm
1:1
Scale

Tube Module B Assembly
1 2
11.5 cm
7
A1
11.5cm
11.5cm
2 1
14 cm
1:1
Scale
1:1
Scale Prepare air tube before
assembly.
Prepare air tube
before assembly.
14cm

3
5
B1
1
2
P13
B3
P14
8
P19
01x2
P20
A1
Screw P14 to PET bottle tightly
to avoid air leakage.
4

How To Oil The Parts
B8
9
6
Tissue Paper
P16
B8
B7
Note : Oil the parts when appears.
Do not oil outside the shadow as shown below.
Example:
Do not spill any oil from the B7
oil sink. Keep oil contained.
Apply Oil

7
D16
Red Cap
(Small)
P10
Video Tips
Scanning the QR code to help you
assemble below steps smoothly.
htt ps:/ /yout u.be/ mmzSFocksso
Make sure P10 is placed in the
proper direction to avoid
air leakage.
10
9
10
D12
D20
Push & pull the oiled part
D16 several times to
make it work smoothly.
2
1
8

4
htt ps:/ /yout u.be/ B2l8FHszi5c
Scanning the QR code to help you assemble below
steps smoothly.
Video Tips
P17
B14
P17
12
E2
P9
O-ring
(Black)
P9
O-ring
(Black)
B14
A3
E2
1 2 3
C5
Use C5 to assist you in
setting P9 to E2 entirely.
2
1
P4
5
6
Valve Assembly
Ensure the direction of two
P17 to avoid air leakage.
Use B14 to assist
you in setting two P9
entirely.
1
Push P17 to the
bottom (as per Fig )
and make P9 to
set flatly.
1
Push P17 to the top (as per Fig )
and make P9 to set flatly.
2
Straight P4 on the
table, cap B14 to P4
as shown .
Pay close attention to the following
steps correctly to avoid air leakage.
If P9 (O-Ring) was set improperly as shown
in above wrong fig, re-do step 6 again.
A3
Snap E2 to A3 entirely to avoid
air leakage.
4
2. Press down
E2 to A3 entirely.
1. Straight A3 on the table,
and put E2 on A3 flatly.
E2
A3
1 2

P8
11
12 13
E1
04
P19
11
B2
03
P19
Note:
Give a slight pull on
both ends of the spring
to make sure of good
strength & extension
before assembly.

Video Tips
Scanning the QR code to help you assemble below steps smoothly.
htt ps:/ /yout u.be/ Jgh963Gc2i0
Air Leakage Testing – The Valve
13
1
2
P12
Red Cap (Big)
D4
D4
1Seal the hole of the boss side with a finger.
2Push in the D4.
P17
Make sure that both P17 move to the
direction indicated by the arrows when
the D4 is pushed in.
Make sure that both P17 move in the
direction indicated by the arrows when
the D4 is pulled back.
Confirm that the D4 cannot be
pushed in easily.

14
2
2
1
1
Fold the tube and insert it to the hole as shown below.
Air leakage testing – Tube Module B
Fold the tube.
Insert the folded tube to the hole.
1Seal the hole of the concave side with a finger.
2Pull the D4 back.
1
2
E2
Install E2 at a right position as
shown above.
Confirm that pulling the D4 back is
hard, or you need more power to pull
the D4 back.

3
D4
A3
Pointer stays still Pointer turns to above position
15
Air Leakage Working Functionally
Hold A3 firmly!
Repeat a “ Push & Pull” movement using D4
15~20 times to collect air into PET bottle.
Check pressure meter and examine the position
that the pointer swings to.
Results shown below will reveal if tube module B is
installed functionally or experiencing air leakage.

4
Position 1:
Back to page8 , and re-install step 5 again.
Position 2:
Back to page10, and re-install steps 7~13 again.
Position 3:
Back to page12, and re-install steps 1~6 again.
Check following positions if air leakage was occurred,
and re-install as below:
Position 1:
Position 2: Position 3:
2
1
D4
Be sure to remove air tube & D4 from A3
after testing is finished.
16
Put D4 aside B7 to avoid oil spilling with others.

D2
C6
D5
D5
P6
17
1
2
Scale 1:1
1
2
2
1
Vehicle Body Module Assembly
Insert P6 hex shaft to the bottom as
indicated on the right fig. ( scale 1:1 )
Make sure parts D2/D5 are at opposite positions.

P1x2
C3
18
3
1
2
D5
D2
Scale 1:1
Push parts D5 & D2 to the
bottom as shown above.

P1x4
C1
19
4
5
2
Scale 1:1
1